WEG UR11 Series User manual

Rectifier Unit
Unidad Rectificadora
Unidade Retificadora
UR11
Motors | Automation | Energy | Transmission & Distribution | Coatings
User's Manual
Manual del Usuario
Manual do Usuário

03/2015
Series: UR11
Language: English
Document: 10001149720 / 01
Models: 1140 A / 380...480 V
893 A / 500…600 V
811 A / 660…690 V
RECTIFIER UNIT
MANUAL
UR11

4
Version Revision Description
- R00 First edition.
- R01 Updating of the figures and general revision.
Summary of Revisions

Contents
1 SAFETY INSTRUCTIONS.................................................................. 1-1
1.1 SAFETY WARNINGS IN THE MANUAL......................................................... 1-1
1.2 SAFETY WARNINGS IN THE PRODUCT........................................................ 1-1
1.3 PRELIMINARY RECOMMENDATIONS........................................................... 1-2
2 GENERAL INSTRUCTIONS .............................................................. 2-1
2.1 ABOUT THE MANUAL ................................................................................. 2-1
2.2 TERMS AND DEFINITIONS USED IN THE MANUAL ..................................... 2-1
2.3 ABOUT THE UR11 .................................................................................... 2-4
2.4 IDENTIFICATION LABEL FOR THE UR11 ...................................................... 2-8
2.5 HOW TO SPECIFY THE UR11 MODEL (SMART CODE).................................. 2-8
2.6 RECEIVING AND STORAGE......................................................................... 2-9
3 INSTALLATION AND CONNECTION............................................... 3-1
3.1 ENVIRONMENTAL CONDITIONS ................................................................ 3-1
3.2 LIST OF COMPONENTS............................................................................... 3-1
3.3 MECHANICAL INSTALLATION..................................................................... 3-2
3.4 ELECTRICAL INSTALLATION ........................................................................ 3-6
3.4.1 Input Circuit Breaker .......................................................................... 3-6
3.4.2 Cables/Bus Bars ................................................................................. 3-6
3.4.3 Fuses.................................................................................................. 3-7
3.4.4 Terminals Recommended for Power Cables........................................ 3-9
3.4.5 Configurations of the Rectifier ........................................................... 3-9
3.4.5.1 Operation as 6 Pulse Rectifier............................................. 3-10
3.4.5.2 Operation as 12 Pulse Rectifier........................................... 3-11
3.4.6 UR11 Connections............................................................................ 3-13
3.4.6.1 Panel Layout and Connections ........................................... 3-13
3.4.6.2 Power Connections ............................................................ 3-13
3.4.6.3 Grounding Connections ..................................................... 3-16
3.4.6.3.1 IT Network .......................................................... 3-17
3.4.6.4 Control Connections .......................................................... 3-18
3.4.7 Typical Connections ......................................................................... 3-20
3.5 INSTALLATION ACCORDING TO THE EUROPEAN DIRECTIVE OF
ELECTROMAGNETIC COMPATIBILITY .............................................................. 3-23
3.5.1 Conformal Installation with the CFW-11M........................................ 3-23
3.5.2 Standard Definitions ........................................................................ 3-23
3.5.3 Emission and Immunity Levels.......................................................... 3-24
3.5.4 External RFI Filters............................................................................ 3-24
4 FIRST TIME POWER-UP AND START-UP .......................................... 4-1
4.1 PREPARE FOR START-UP .............................................................................. 4-1
4.1.1 Precautions During the Energization/Start-up ................................... 4-1
4.2 START-UP .................................................................................................... 4-1

Contents
5 TROUBLESHOOTING AND MAINTENANCE ................................... 5-1
5.1 OPERATION OF THE FAULTS AND ALARMS ................................................ 5-1
5.2 FAULTS, ALARMS, AND POSSIBLE CAUSES.................................................. 5-1
5.3 SOLUTIONS FOR THE MOST FREQUENT PROBLEMS ................................... 5-3
5.4 INFORMATION FOR CONTACTING TECHNICAL SUPPORT.......................... 5-3
5.5 PREVENTIVE MAINTENANCE ...................................................................... 5-3
5.5.1 Cleaning Instructions ......................................................................... 5-5
6 OPTION KITS AND ACCESSORIES .................................................. 6-1
6.1 OPTION KITS ............................................................................................. 6-1
6.2 ACCESSORIES ............................................................................................ 6-1
6.2.1 Rack Panel Assembly.......................................................................... 6-1
7 TECHNICAL SPECIFICATIONS......................................................... 7-1
7.1 POWER DATA .............................................................................................. 7-1
7.2 ELECTRICAL / GENERAL SPECIFICATIONS................................................... 7-2
7.2.1 Codes and Standards ......................................................................... 7-3
7.3 MECHANICAL DATA.................................................................................... 7-3
7.3.1 Weight .............................................................................................. 7-3
7.3.2 Dimensions ........................................................................................ 7-3

Safety Instructions
UR11 | 1-1
1
1 SAFETY INSTRUCTIONS
This manual provides information for the proper installation and operation of the Rectifier Unit UR11 developed
to perform the rectification for the CFW-11M product line.
Only trained and qualified personnel should attempt to install, start-up, and troubleshoot this type of equipment.
1.1 SAFETY WARNINGS IN THE MANUAL
The following safety warnings are used in this manual:
DANGER!
The procedures recommended in this warning have the purpose of protecting the user against dead,
serious injuries and considerable material damage.
ATTENTION!
The procedures recommended in this warning have the purpose of avoiding material damage.
NOTE!
The text supplies important information for the correct understanding and good operation of the
product.
1.2 SAFETY WARNINGS IN THE PRODUCT
The following symbols are attached to the product and require special attention:
High voltages are present.
Components sensitive to electrostatic discharge.
Do not touch them.
Mandatory connection to the protective ground (PE).
Connection of the shield to the ground.
Hot surface.

Safety Instructions
1-2 | UR11
1
1.3 PRELIMINARY RECOMMENDATIONS
DANGER!
Only trained personnel, with proper qualifications, and familiar with the UR11 and associated machinery
shall plan and implement the installation, starting, operation, and maintenance of this equipment.
The personnel shall follow all the safety instructions described in this manual and/or defined by the
local regulations.
Failure to comply with the safety instructions may result in death, serious injury, and equipment damage.
NOTE!
For the purpose of this manual, qualified personnel are those trained and able to:
1. Install, ground, power-up, and operate the UR11 according to this manual and to the current
legal safety procedures.
2. Use the protection equipment according to the established regulations.
3. Provide first aid
DANGER!
Always disconnect the main power supply before touching any electrical device associated with the rectifier.
Several components may remain charged with high voltage and/or in movement (fans), even after
the AC power supply has been disconnected or turned off.
When there is a capacitive load connected to the UR11 output (e.g. frequency inverters fed directly
from the DC link), wait at least 10 minutes to guarantee the fully discharge of capacitors.
Always connect the equipment frame to the protection earth (PE) at the suitable connection point.
ATTENTION!
The electronic boards contain components sensitive to electrostatic discharges. Do not touch the
components and terminals directly. If needed, touch first the grounded metal frame or wear an
adequate ground strap.
Do not perform a withstand voltage test on any part of the rectifier unit!
If needed, please, consult WEG.
NOTE!
Rectifiers may cause interference in other electronic devices. Follow the recommendations listed in
chapter 3 INSTALLATION AND CONNECTION on page 3-1, to minimize these effects.
NOTE!
Fully read this manual before installing or operating the rectifier unit UR11.
ATTENTION!
The operation of this equipment requires installation instructions and detailed operation provided
in this manual.

General Instructions
2
UR11 | 2-1
2 GENERAL INSTRUCTIONS
2.1 ABOUT THE MANUAL
This manual presents how to install, operate, the main features and basic troubleshooting of the UR11 (rectifier
unit) models.
For more information on other features, accessories and operating conditions, refer to the following mounting
guide:
RACK 2/RACK 3 mounting guide.
The mounting guide is available in the CD-ROM provided with the rectifier unit or it can be downloaded from
WEG website at - www.weg.net.
2.2 TERMS AND DEFINITIONS USED IN THE MANUAL
Normal Duty Cycle (ND): inverter duty cycle that defines the maximum continuous operation current (Inom-ND) and
the overload current (110 % for 1 minute). It is selected according to the programming of the inverter connected to
the rectifier output. This duty cycle shall be used for the operation of motors that are not subjected to high torque
loads (with respect to the motor rated torque) during its operation, starting, acceleration, or deceleration.
Inom-ND:inverter rated current for use with the normal duty (ND) cycle.
Overload: 1.1 x Inom-ND / 1 minute.
Heavy Duty Cycle (HD): inverter duty cycle that defines the maximum continuous operation current (Inom-HD) and
the overload current (150 % for 1 minute). It is selected according to the programming of the inverter connected
to the rectifier output. This duty cycle shall be used for the operation of motors that are subjected to high torque
(with respect to the motor rated torque) during its operation, starting, acceleration, or deceleration.
Inom-HD:inverter rated current for use with the heavy duty (HD) cycle.
Overload: 1.5 x Inom-HD / 1 minute.
Current Unbalance (%):
unbalance at rectifier unit X - phase Y = x 100
IYX - IYAVG
IYAVG
IYAVG = IY1 + IY2 + ... + IYN
N
Where:
N = number of power units.
IYN = Y phase current (R, S or T) of the rectifier unit N.
IYAVG = Y phase average current.
Rectier: input circuit of inverters that transforms the AC input voltage in DC voltage. It is composed of power
diodes.

General Instructions
2
2-2 | UR11
Pre-charge Circuit: transitional stage of the UR11 operation, which starts when the power is applied to the
input phases and ends with the complete charging of the DC link capacitors of the inverter connected to its
output. This step is controlled by the UR11, which performs the loading of DC link capacitors through a voltage
ramp with limited current, avoiding high current spikes on the inverter startup.
DC Link: inverter intermediate circuit with DC voltage and current, obtained from the rectification of the AC
supply voltage via UR11, or from an external source; it supplies the output IGBTs inverter bridge.
Inverter Circuit: circuit to modify the DC voltage of the DC Link.
Diode: basic component of the input rectifier bridge. It works like an electronic key (controlled by the voltage
polarity of the anode and cathode terminals), in the following modes: conduction (closed switch, terminals
directly polarized) and blocked (open switch,terminals reversely polarized).
Thyristor (SCR): Silicon-Controlled Rectifier; basic component of the input rectifier. It works like a diode but
it needs a voltage pulse in the gate terminal to be able to get into the conduction mode, besides the proper
polarization of the anode and cathode terminals, which allows the control of the starting conduction angle.
IGBT: Insulated Gate Bipolar Transistor; basic component of the output inverter bridge. The IGBT works as an
electronic switch in the saturated (closed switch) and cut-off (open switch) modes.
Braking IGBT: operates as a switch for the activation of the braking resistor. It is commanded by the DC Link
level, through the output inverter.
R, S e T Arm: it is a set of one diode and one thyristor of the R, S and T phases of the rectifier input.
Power Modules U, V, and W: set of two IGBTs of the inverter output phases U, V, and W.
Bridge 1 (and bridge 2): it is a set of three thyristors and three diodes, making a semi-controlled rectifier unit.
6 Pulses Rectier: three-phase rectifier configuration, where each power diode operates for 120° and
commutates every 60°, performing six commutations in one cycle of the power supply.
12 Pulses Rectier: six-phase rectifier configuration, regularly available through a phase shifting transformer
with two secondaries connected in delta and star, where each power diode operates for 120° and commutates
every 30°, performing twelve commutations in one cycle of the power supply.
PTC: resistor which resistance value in ohms increases proportionally to the temperature increase; used as a
temperature sensor in electrical motors.
NTC: resistor which resistance value in ohms decreases proportionally to the temperature increase; used as a
temperature sensor in power modules.
PE: Protective Earth.
RFI Filter: Radio-Frequency Interference Filter for interference reduction in the Radio-Frequency range.
PWM: Pulse Width Modulation; pulsed voltage that feeds the motor.

General Instructions
2
UR11 | 2-3
Switching Frequency: frequency of the IGBTs switching in the inverter bridge, normally expressed in kHz.
Heatsink: metal device designed to dissipate the heat generated by the power semiconductors.
Amp, A: ampères.
°C: celsius degree.
AC: alternated current.
DC: direct current.
CFM: Cubic Feet per Minute; unit of flow.
cm: centimeter.
hp: horse power = 746 Watts; unit of power, used to indicate the mechanical power of electrical motors.
Hz: hertz.
l/s: liters per second.
kg: kilogram = 1000 grams.
kHz: kilohertz = 1000 Hertz.
m: meter.
mA: miliampère = 0.001 Ampère.
min: minute.
ms: millisecond = 0.001 seconds.
N.m.: newton meter; unit of torque.
rms: "root mean square"; effective value.
rpm: revolutions per minute; unit of speed.
s: second.
V: volts.
Ω: ohms.

General Instructions
2
2-4 | UR11
2.3 ABOUT THE UR11
The rectifier unit UR11 provides DC voltage to feed the CFW-11M inverters. The UR11 can also be used to
provide power to other devices that require DC link voltage. The main feature of this product is the two built-in
complete semi-controlled rectifier bridges, which have the advantages presented next:
DC link pre-charge control, provided by the control of the thyristors firing angle through a microcontroller:
the pre-charge provides a linear voltage ramp, avoiding high currents and eliminating the pre-charge circuit
of the panels.
The independent control of each rectifier unit of the UR11, together with the two triphasic chokes with
3 % voltage drop, allows the use of this product in applications where 12-pulse rectifier configuration is
required by simply connecting the power cables properly (for details, see chapter 3 INSTALLATION AND
CONNECTION on page 3-1).
The UR11 product line with its modular structure (book type) is very similar to the CFW-11M power units (UP11),
which makes it very appropriate for the assembly in panels with the CFW-11M inverter line. Each rectifier unit
is able to provide power to two UP11 power units. In order to feed more than two UP11 it is just necessary to
add more rectifier units in parallel proportionally.
Figure 2.1 on page 2-4 presents an example of diagram for a 6 pulse rectifier operation and Figure 2.2 on
page 2-5 presents an example of diagram for a 12 pulse rectifier operation.
R1, S1, T1
L1 L2
R, S, T
Power
supply
3∼
UR11
+UD, -UD
F1, F2, F3 F4, F5, F6
R2, S2, T2
Figure 2.1 - Example of diagram of a 6 pulse conguration with one rectier unit

General Instructions
2
UR11 | 2-5
R1, S1, T1
L1 L2
Power
supply
3∼
UR11
+UD, -UD
F1, F2, F3 F4, F5, F6
R2, S2, T2
Figure 2.2 - Example of diagram of a 12 pulse conguration with one rectier unit
The UR11 can be provided together with the complete panel (AFW-11M) or as a stand-alone product to be
assembled in a panel. For the complete panel, all the components are provided in the panel.
NOTE!
Several additional items are needed for the complete panel assembly, such as: output inverters, AC
fuses, DC link fuses for the output power units protection, circuit breaker or disconnect switch at the
input and in case of 12 pulse configuration is also necessary to provide a phase shifting transformer.
The UR11 has an interface board feed by a +24 Vcc external power supply. This board presents three output
relays for alarm and fault indication, five LEDs for fault visualization, as well as the rectifier bridges status. There
are also two DIP switches for the voltage settings of the UR11 power supply, according to the model (refer to
item 3.4.6.4 Control Connections on page 3-18 for more information). This board is also responsible for the
heatsink temperature monitoring.
Figure 2.3 on page 2-6 shows a simplified block diagram of the UR11.

General Instructions
2
2-6 | UR11
Cabinet aux.
power supply
220 V Ext.
UR11
NTCs
PE
LEDs
Feedback:
- input voltage
Digital outputs
DO1 (RL1) to
DO3 (RL3)
DC Bus
(DC Link)
Feedback:
- DC link voltage
- heatsink temperature
CPC11
Supply board and thyristor control with the 32
bits "RISC" CPU.
CIR11
User
interface
board
Power supply
+24 Vdc
Ext.
Power section fans
Rectifier
Rectifier
POWER
CONTROL
Figure 2.3 - Block diagram for the UR11
Input reactor
Thyristors decoupling capacitors
Board CPC11
Board RCS4
Board CLR1
Board CIR11
Fan
Synchronism
transformer fuses
Figure 2.4 - UR11 main components

General Instructions
2
UR11 | 2-7
Heatsink fans
External 220 V
+UD -UD
A...F +UD
+UD
-UD
J2
J1
J3
V1 V2
5
AB C D E F
C1 C2
5 5 5 5 54
1 1 1 1 1 1
4 4 4 4 4
2 2 2 2 2 2
333333
XC4
XE1
XN2XN2
L1 L2
(2)(1) XC15AXC15A
1
2
3
4
5
6
6
5
4
3
2
1
XIT
GND
CPC11CPC11
6 x TD570N
-UD
Obs.: 6 x RCS4
CLR1
RCS4
R1 S1 T1 R2 S2 T2
Figure 2.5 - UR11 general internal diagram: power connections
External
+24 Vdc
RL1
UDC1 / UDC2
OK
+24 Vdc
RL2 without
temperature
alarm
RL3 without
temperature fault
A
A
B
B
C
C
D
D
E
E
F
F
1
2
2
3
3
4
5
6
7
8
9
J1
T1
T2
F2
F3
F4
F5
F6
N2
N1
VT2
VT1
VS2
VS1
VR2
VR1
F1
(1)
(2)
XC1
XC2
(+) (+)
+
(-) (-)
XC16
XC16
XC102
XC101
XC3R
XC3S
XC3T
XC10
XC10
CPC11 NTC_R
NTC_S
NTC_T
CPC11
CIR11
1
Figure 2.6 - UR11 general internal diagram: control connections

General Instructions
2
2-8 | UR11
2.4 IDENTIFICATION LABEL FOR THE UR11
There are two identification labels, one located at the front cover and another inside the UR11 enclosure, close
to the fans.
Rated output data (voltage, rated currents
for use with Normal Duty (ND) and Heavy
Duty (HD))
Maximum surrounding air
temperature
Manufacturing date
Serial number
Rated input data (voltage, input phase
numbers, rated currents for Normal Duty
(ND) and Heavy Duty (HD) cycles, overload
current for 1 min and 3 s and frequency)
Current specifications for use with the
Heavy Duty (HD) cycle
Current specifications for use with the
Normal Duty (ND) cycle
UR11 Model
WEG part number
UR11 Net weight
Figure 2.7 - UR11 identication label
Figure 2.8 - Location of the identication labels
2.5 HOW TO SPECIFY THE UR11 MODEL (SMART CODE)
In order to specify the UR11 model it is necessary to indicate the desired voltage and current values in their
respective fields for the nominal supply voltage and the rated input current for normal duty overload (ND) in
the smart code according to the example of the Table 2.1 on page 2-9.

General Instructions
2
UR11 | 2-9
The available options for the rectifier input current on normal duty (ND) overload are presented at Table 2.2 on
page 2-9 according to the input rated voltage. In order to check other data refer to the technical specifications
at Table 7.1 on page 7-2.
Table 2.1 - Smart code
Rectier Model
Refer to chapter 7 TECHNICAL SPECIFICATIONS on page 7-1 for a list
of models for the UR11 series and the rectifiers technical specification.
Example EX UR11 1140 T 4 S Z
Field
description.
Market identification
(defines the manual
language).
WEG Rectifier
Unit - 11 series.
Rated input
current for use
with the Normal
Duty (ND) cycle.
Number of input
phases.
Rated input voltage. Option kit. Character that
identifies
the code end.
Available
options.
T= three-phase. 4 = 380...480 V.
5 = 500...600 V.
6 = 660...690 V.
S = standard
product.
E.g.: UR111140T4SZ corresponds to a 1140 A three-phase UR11 rectifier, with 380 V to 480 V input voltage (input
power supply). A 500 / 600 V rectifier would be specified as UR110893T5SZ and a 660 / 690 V would be specified
as UR110811T6SZ.
Table 2.2 - Nominal currents at normal overload regime (ND)
Voltage Current
380 / 480 V 1140 =1140 A
500 / 600 V 0893 = 893 A
660 / 690 V 0811 = 811 A
2.6 RECEIVING AND STORAGE
The UR11 rectifier units are supplied packed in wooden boxes (refer to the Figure 2.9 on page 2-9).
Figure 2.9 - UR11 packing
There are identification labels outside these boxes, identical to the ones fixed on the product.
In order to open the box:
1. Put the box on the floor.
2. Open the wood crate.
3. Remove all the packing material (the cardboard or styrofoam protection) before removing the UR11.

General Instructions
2
2-10 | UR11
Check the following items once the rectifier is delivered:
Verify that the product identification label corresponds to the model number on your purchase order.
Inspect the product for external damaging during transportation.
Report any damage immediately to the carrier that delivered your product.
If the products were note installed immediately, store them in a clean and dry place (temperature between
-25 °C and 60 °C (77 °F and 140 °F)) with a cover in order to avoid the contamination with dust.
Figure 2.10 - Do not tilt the rectier units

Installation and Connection
3
UR11 | 3-1
3 INSTALLATION AND CONNECTION
This chapter provides information on installing and wiring the UR11. The instructions and guidelines listed in
this manual shall be followed in order to guarantee personnel and equipment safety, as well as the proper
operation of the rectifier.
3.1 ENVIRONMENTAL CONDITIONS
Avoid installing the UR11 in an area with:
Direct exposure to sunlight, rain, high humidity, or sea-air.
Inflammable or corrosive gases or liquids.
Excessive vibration.
Dust, metallic particles, and oil mist.
Environment conditions for the operation:
Temperature: -10 °C to 45 °C (14 °F to 113 °F) - nominal conditions (measured around the rectifier).
From 45 °C to 55 °C (113 °F to 131°F) - 2 % current derating for each Celsius degree.
Air relative humidity: from 5 % to 90 % non-condensing.
Altitude: up to 1000 m (3.300 ft) - standard conditions.
From 1000 m to 4000 m (3.300 ft to 13.200 ft) - 1 % of current derating for each 100 m (or 0.3 % each
100 ft) above 1000 m (3.300 ft) up to 4000 m (13.200 ft) maximum altitude.
From 2000 m to 4000 m (6.600 ft to 13.200 ft) - 1,1 % of maximum voltage derating for each 100 m (or
0.33 % each 100 ft) above 2000 m (6.600 ft) up to 4000 m (13.200 ft) maximum altitude.
Pollution degree: 2 (according to EN50178 and UL508C) with non-conductive pollution. Condensation
shall not originate conduction through the accumulated residues.
3.2 LIST OF COMPONENTS
The UR11 rectifier was developed to perform the rectification of the incoming three-phase power supply and
provide the proper DC link voltage to the CFW-11M line. It replaces the pre-charge circuit and the line reactor
(or the interphase reactor when the 12 pulse configuration is required). It is possible to add rectifier units in
parallel for applications that demand higher currents than the rated current of one rectifier unit (see Table 3.1
on page 3-2 to Table 3.3 on page 3-2).

Installation and Connection
3
3-2 | UR11
Table 3.1 - Currents and conguration in 380 / 480 V
Nominal Current (A) Number of
Power Units
UR11 in
Parallel
ND ND
600 515 1
1140 979 1
1710 1468 2
2280 1957 2
2850 2446 3
Table 3.2 - Currents and conguration in 500 / 600 V
Nominal Current (A) Number of
Power Units
UR11 in
Parallel
ND ND
470 380 1
893 722 1
1340 1083 2
1786 1444 2
2232 1805 3
Table 3.3 - Currents and conguration in 660 / 690 V
Nominal Current (A) Number of
Power Units
UR11 in
Parallel
ND ND
427 340 1
811 646 1
1217 969 2
1622 1292 2
2028 1615 3
The other panel components are responsibility of the integrator. Among these components we can point out
the AC input fuses, DC link fuses for power units protection, circuit breaker or disconnect switch, phase-shifting
transformer for 12-pulse configuration, bus bars, panel fans, etc.
3.3 MECHANICAL INSTALLATION
The power units must be properly secured in the drive cabinet, making it possible the easy withdrawal and
reinsertion in case of maintenance. The fastening must also be done so that it prevents panel transportation
damage.
The "panel mounting rack" accessory simplifies the mounting of the power units and allows their simple fastening
and movement. Refer to "Rack 2/Rack 3 Mounting Guide".

Installation and Connection
3
UR11 | 3-3
∅ 22.5 mm (0.89 in) hoisting eyes - weight 286 Kg (630.52 lb)
Figure 3.1 - UR11: hoisting eyes
Figure 3.2 - Mounting of the UR11 side by side without lateral spacing