Weider 8530 WESY85301 User manual

USERÕS MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Model No. WESY85301
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal (Under Seat)
PATENT PENDING
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!

2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions before
using the home gym system.
1. Read all instructions in this manual and in
the accompanying literature before using the
home gym system.
2. Use the home gym system only on a level
surface. Cover the floor beneath the home
gym system to protect the floor or carpet.
3. Inspect and tighten all parts often. Replace
any worn parts immediately.
4. Keep small children and pets away from the
home gym system at all times.
5. Always wear athletic shoes for foot protec-
tion.
6. Keep hands and feet away from moving
parts. Keep hands away from the squat arm
upright when the squat arm is being used.
Your hand could become pinched between
the squat arm upright and the squat arm.
7. Always stand on a foot plate when perform-
ing an exercise that could cause the home
gym system to tip.
8. Never release the press arm, butterfly arms,
squat arm, leg lever, lat bar or nylon strap
while weights are raised. The weights will fall
with great force.
9. Do not use the VKR station when either
weight stack is in use.
10. Make sure that the cables remain on the pul-
leys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
11. Always disconnect the lat bar from the home
gym system when performing an exercise
that does not use the lat bar.
12. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
13. It is the responsibility of the owner to ensure
that all users of this home gym system are
adequately informed of all warnings and pre-
cautions.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
HOW TO USE THE HOME GYM SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
TROUBLE-SHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of
this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before
beginning assembly.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.

3
BEFORE YOU BEGIN
ASSEMBLED
DIMENSIONS:
Height: 74 in.
Width: 60 in.
Length: 54 in.
Foot Plate
Low Pulley Station
High Pulley Station
Lat Bar
Leg Lever
Butterfly Arms
Squat Arm
Press Arm
Weight Stacks
Backrest
VKR Arms
Weight Pin
Thank you for selecting the versatile WEIDER¨8530
Home Gym System. The WEIDER¨8530 offers a
selection of weight stations designed to develop every
major muscle group of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
WEIDER¨8530 will help you to achieve the specific
results you want.
For your benefit, read this manual carefully before
using the WEIDER
¨
8530 Home Gym System. If you
have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
WESY85301. The serial number can be found on a
decal attached to the WEIDER¨8530 (see the front
cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

4
ASSEMBLY
1
74
56
3
3
8
11
51
27
1
4
3
1
51
27
High
Side
5
1. Before beginning assembly, be sure that
you have read and understand the infor-
mation in the box above.
Press a 2Ó Inner Cap (27) into the indicated
end of the Stabilizer (5). Press 2Ó Outer
Caps (51) onto the other two locations on
the Stabilizer. Press a 2Ó Inner Cap into the
end of the Base (4).
Insert four 5/16Ó x 2 1/2Ó Carriage Bolts (1)
up through the Stabilizer (5).
Attach the Base (4) to the Stabilizer (5) with
two 5/16Ó x 2 3/4Ó Bolts (11), two 5/16Ó Flat
Washers (8), and two 5/16Ó Nylon Locknuts
(3). Do not tighten the Nylon Locknuts
yet.
Slide the VKR Upright (74) and the Squat
Arm Upright (56) onto the 5/16Ó x 2 1/2Ó
Carriage Bolts (1) in the Stabilizer (5). The
high side of the brackets on the VKR
Upright and Squat Arm Upright should be
on the side shown. Hand-tighten four 5/16Ó
Nylon Locknuts (3) onto the Carriage Bolts.
Do not tighten the Nylon Locknuts yet.
FRAME ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
¥Place all parts of the WEIDER 8530 in a cleared
area and remove the packing materials; do not
dispose of the packing materials until assembly is
completed.
¥ The assembly is broken into five stages: 1) frame
assembly, 2) press and butterfly arm assembly,
3) cable and pulley assembly, 4) seat and back-
rest assembly, and 5) VKR assembly. The hard-
ware for each stage is packaged separately.
¥ Wait until you begin each assembly stage to open
the parts bag labeled for that assembly stage.
¥For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the center of this manual.
Note: Some small parts may have been pre-
attached for shipping. If a part is not in the parts
bag, check to see if it has been pre-attached.
¥As you assemble the WEIDER 8530, be sure that
all parts are oriented as shown in the drawings.
¥Tighten all parts as you assemble them, unless
instructed to do otherwise.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
¥ Two (2) adjustable wrenches
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ One (1) rubber mallet
¥ Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.

4
2
3
5
2. Insert two 5/16Ó x 2 1/2Ó Carriage Bolts (1) up
through the Base (4).
Slide the Front Upright (42) onto the 5/16Ó x
2 1/2Ó Carriage Bolts (1) in the Base (4).
Hand-tighten a 5/16Ó Nylon Locknut (3) onto
each Carriage Bolt. Do not tighten the
Nylon Locknuts yet.
Press a 1Ó Inner Cap (6) into the Front
Upright (42). Press a 2Ó Inner Cap (27) into
the Squat Upright (56). Press a 2Ó Inner Cap
into the VKR Upright (74).
3. Press a 2Ó Inner Cap (27) into the end of the
Top Frame (55). Press a 1 3/4Ó Inner Cap
(44) into each end of the crossbar on the Top
Frame. Press two Inner Caps (96) into the top
of the crossbar.
Attach the Top Frame (55) to the Front
Upright (42) with two 5/16Ó x 2 3/4Ó Bolts (11),
two 5/16Ó Flat Washers (8), and two 5/16Ó
Nylon Locknuts (3).
Attach the Top Frame (55) to the VKR Upright
(74) and the Squat Upright (56) with two 5/16Ó
x 2 3/4Ó Bolts (11) and two 5/16Ó Nylon
Locknuts (3).
Tighten all of the Nylon Locknuts used in
steps 1Ð3.
4. Set two Weight Bumpers (19) on the bracket
on the Base (4) as shown. Set two Weight
Bumpers (19) on the bracket on the Stabilizer
(5).
Stack eight Weights (25) onto each set of
Weight Bumpers (19). Be sure that the pin
grooves are all on the same side of each
stack of Weights.
Be careful not to tip either stack of
Weights (25) until step 6 is complete.
FRAME ASSEMBLY
27
55 3
11
896
44
44
Crossbar
3
42
11
74
56
25
19
19
25
5ÑBracket
Pin
Grooves
Pin
Grooves
4ÑBracket
1
4
3
6
42
27
27
74
56

5
6
6
5. Press a Weight Tube Bumper (64) into the
end of a Weight Tube (63). Insert the Weight
Tube into the front stack of Weights (25). Be
sure that the pins on the Weight Tube are
sitting in the pin grooves in the top
Weight.
Lubricate the inside of the holes in a Top
Weight (65). Set the Top Weight onto the front
stack of Weights (25). Insert both Long
Weight Guides (62) into the stack of Weights.
Be sure that the holes in the Weight
Guides are at the top, as shown.
6. Press a Weight Tube Bumper (64) into the
end of the other Weight Tube (63). Insert the
Weight Tube into the rear stack of Weights
(25). Be sure that the pins on the Weight
Tube are sitting in the pin grooves in the
top Weight.
Lubricate the inside of the holes in the other
Top Weight (65). Set the Top Weight onto the
rear stack of Weights (25). Insert both Short
Weight Guides (73) into the stack of Weights.
Be sure that the holes in the Weight
Guides are at the top, as shown.
FRAME ASSEMBLY
62
Holes
Pin
63
Lubricate
64
25
65
Lubricate
Holes
Pin
73
65
63
64
25

7. Attach the upper ends of the Long Weight
Guides (62) to the Top Frame (55) with a
5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers
(61), and a 5/16Ó Nylon Locknut (3).
Be sure that the Pulley Bracket (20) is in
front of the right Long Weight Guide (62)
as shown.
Attach the upper ends of the Short Weight
Guides (73) to the Top Frame (55) with a
5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers
(61), and a 5/16Ó Nylon Locknut (3).
8. Press a 1Ó x 7/8Ó Plastic Bushing (90) onto
each welded spacer on the Press Frame (17).
Slide the Press Frame into place onto the
Base (4). Note: This will be a tight fit. The
Plastic Bushings should fit on each end of
the indicated tube in the Base. Make sure
that the pulleys are on the side shown.
Lubricate the 3/8Ó x 8Ó Bolt (59). Attach the
Press Frame (17) to the Base (4) with the
3/8Ó x 8Ó Bolt and a 3/8Ó Nylon Locknut (21).
9. Wet the handle of one Press Arm (46) with
soapy water. Slide a 5Ó Plastic Grip (83) onto
the handle. Press a 1Ó Round Inner Cap (49)
into the other end of the handle. Press a
1 3/4Ó Inner Cap (44) into the Press Arm.
Attach the Press Arm (46) to one side of the
Press Frame (17) with two 5/16Ó x 2 1/2Ó
Bolts (22) and two 5/16Ó Nylon Locknuts (3).
Assemble the other Press Arm (46) in the
same manner.
10. Identify the Right Arm (48) and the Left Arm
(47). Note the position of the welded bracket
on each Arm. Arm identification is very
important for step 11.
Attach a ÒVÓ-Pulley (50) and a Long Cable
Trap (31) to the Right Arm (48) with a 3/8Ó x
2 1/2Ó Bolt (86) and a 3/8Ó Nylon Locknut
(21).
Attach a ÒVÓ-Pulley (50) and a Long Cable
Trap (31) to the Left Arm (47) in the same
manner.
7
8
9
10
ARM ASSEMBLY
FRAME ASSEMBLY
7
60
61 361 3
55
60
20
73 62
17
59
Lubricate
90
4ÑTube
21
Welded
Spacers
44
49
83
46
17
22
3
Handle
46
48
Welded
Bracket
47
50
50
31
31
86
21

8
11. Lubricate both axles on the Top Frame (55).
Slide the Right Arm (48) onto the right axle.
Be careful not to confuse the Right Arm
with the Left Arm (47); note the position of
the ÒVÓ Pulley (50) to identify the Right
Arm. Be sure that the upper end of the
Right Arm is behind the indicated bracket
on the Top Frame (55).
Tap two 1Ó Retainers (69) and a 1Ó Round
Cover Cap (70) onto the axle. Be sure that
the teeth on the Retainers bend toward the
Round Cover Cap, as shown in the inset
drawing.
Attach the Left Arm (47) in the same manner.
Press 1 3/4Ó Inner Caps (44) into the lower
ends of the Left and Right Arms (47, 48). Wet
the lower end of each Arm with soapy water.
Slide a 10Ó Pad (45) onto the lower end of
each Arm.
12. Press two 1Ó x 2Ó Inner Caps (87) into the
indicated end of the Squat Arm (84).
Attach the Squat Arm (84) to the VKR Upright
(74) with a 3/8Ó x 5 1/2Ó Bolt (93) and a 3/8Ó
Nylon Locknut (21). Be sure that the indicat-
ed bracket is pointing down as shown.
Wet the ends of the Squat Arm (84) with
soapy water. Slide the two Squat Arm Pads
(85) onto the Squat Arm.
Attach a Handle (82) to one side of the Squat
Arm (84) with a 5/16Ó x 2 1/2Ó Bolt (22), two
5/16Ó Flat Washers (8), a 1/2Ó x 17/32Ó Spacer
(91), and a 5/16Ó Nylon Locknut (3).
Wet the Handle (82) with soapy water. Slide a
5Ó Plastic Grip (83) onto the Handle. Press a
1Ó Round Inner Cap (49) into the other end of
the Handle.
Assemble another Handle (82) to the other
side of the Squat Arm (84) in the same man-
ner.
11
12
ARM ASSEMBLY
87
83
82
82
22 85
85
849
91
Bracket
84
93
21
3
74
69
70
AxleÑ
Lubricate
55
50
45
45
69
70
55ÑAxle
48
47
44
44
Bracket

9
During steps 13 to 25, refer to the CABLE DIA-
GRAM on page 19 of this manual. Identify the
three cables by their lengths, and note the
positions of the cable traps. IMPORTANT: Do
not overtighten the bolts and nuts securing
the pulleys. The pulleys must turn freely.
13. Locate the Medium Cable (58). Route the
Medium Cable around the indicated 3 1/2Ó
Pulley (15) attached to the Top Frame (55).
Be sure that the ball is on the indicated
side of the Pulley and that the Cable is
between the Pulley and the hook. Tighten
the 3/8Ó x 3 3/4Ó Bolt (88) and the 3/8Ó Nylon
Locknut (not shown).
14. Wrap the Medium Cable (58) around a ÒVÓ-
Pulley (50). Attach the ÒVÓ-Pulley and a Long
Cable Trap (31) to the indicated bracket on
the Front Upright (42) with a 3/8Ó x 2 1/2Ó Bolt
(86) and a 3/8Ó Nylon Locknut (21). Be sure
that the Long Cable Trap is positioned to
hold the Cable in place.
Route the Medium Cable (58) around the ÒVÓ-
Pulley (50) on the Left Arm (47). Be sure that
the Cable is in the groove of the Pulley and
that the Long Cable Trap (31) holds the
Cable in place. Tighten the 3/8Ó x 2 1/2Ó Bolt
(86) and the 3/8Ó Nylon Locknut (not shown).
15. Route the Medium Cable (58) around the ÒVÓ-
Pulley (50) on the Right Arm (48). Be sure
that the Cable is in the groove of the ÒVÓ-
Pulley and that the Long Cable Trap (31) is
positioned to hold the Cable in place.
Tighten the 3/8Ó x 2 1/2Ó Bolt (86) and the 3/8Ó
Nylon Locknut (not shown).
Route the Medium Cable (58) around the
3 1/2Ó Pulley (15) attached to the Pulley
Bracket (20). Be sure that the Cable is in
the groove of the Pulley and that the Cable
Trap (66) holds the Cable in place. Tighten
the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó
Bolt (not shown). Tighten the 5/16" x 5Ó Bolt
(68) and the 5/16" Nylon Locknut (not shown).
Be sure that the Pulley Bracket swivels freely.
16. See the inset drawing. Attach a 3 1/2Ó Pulley
(15) and a Cable Trap (66) to the upper hole
in the Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó
Bolt (12) and a 3/8Ó Nylon Locknut (21). Be
sure that the Cable Trap is inside the Long
ÒUÓ-Bracket. (Note: This may come pre-
assembled.)
Route the Medium Cable (58) through the
3 1/2Ó Pulley (15) and Long ÒUÓ-Bracket (57)
shown in the inset drawing. Be sure that the
Cable is in the groove of the Pulley and
that the Cable and Pulley move smoothly.
16
13
14
15
CABLE ASSEMBLY
58
15 88
55
Ball
86
86 50
50
31
31
42
Bracket
21
58
47
58
15
20
68
21
66
86
31
48
15
15
66
12
21
58
58
57
57
50
Hook

10
17. Route the Medium Cable (58) around the
3 1/2Ó Pulley (15) attached to the bracket on
the Top Frame (55). Tighten the 3/8Ó x 2Ó Bolt
(12) and the 3/8Ó Nylon Locknut (21). (Note:
This Pulley is pre-assembled. It has been
shown disassembled for easy part identifica-
tion.) Be sure that the Cable is in the
groove of the Pulley and that the Cable
and Pulley move smoothly.
18. Remove the 3 1/2Ó Low Pulley (95) from the
Press Frame (17). Reattach the Pulley with
the 5/8Ó x 9/16Ó Spacer (7) between the
Pulley and the Press Frame. Hand-tighten
the 3/8Ó Nylon Locknut (21).
Locate the Short Cable (23). Route the
Short Cable under the 3 1/2Ó Low Pulley (95).
Be sure that the end of the Cable with the
ball is on the indicated side of the Press
Frame (17) and that the Cable is between
the Pulley and the crossbar on the Press
Frame. Tighten the 3/8Ó Nylon Locknut (21)
and 3/8Ó x 3 3/4Ó Bolt (88).
Route the Short Cable (23) around the 3 1/2Ó
Pulley (15) attached to the lower hole in the
Front Upright (42). Be sure that the Cable
Trap (not shown) is turned to hold the
Cable in place and that the Cable is routed
around the Pulley as shown. Tighten the
3/8Ó Nylon Locknut (21) and 3/8Ó x 3 3/4Ó Bolt
(not shown).
19. Route the Short Cable (23) around the 3 1/2Ó
Pulley (15) attached to the upper hole in the
Press Frame (17). Be sure that the Cable
Trap (66) is in the Ò3 oÕclockÓ position and
that the Cable is routed around the Pulley
as shown. Tighten the 3/8Ó Nylon Locknut
(21) and 3/8Ó x 3 1/2Ó Bolt (not shown).
Route the Short Cable (23) around the 3 1/2Ó
Pulley (15) attached to the upper hole in the
Front Upright (42). Be sure that the Cable
Trap (not shown) is turned to hold the
Cable in place and that the Cable is routed
around the Pulley as shown. Tighten the
3/8Ó Nylon Locknut (21) and 3/8Ó x 3 3/4Ó Bolt
(not shown).
20. Attach the end of the Short Cable (23) to the
Long ÒUÓ-Bracket (57) with a 1/4Ó Nylon
Locknut (2) and a 1/4Ó Flat Washer (10). Do
not tighten the 1/4Ó Nylon Locknut. It
should be threaded onto the Cable only a
couple of turns.
17
18
CABLE ASSEMBLY
21
12
Bracket
55
58
42
21
21
23 9
88
95
7
Ball
15
Crossbar
17
15
12
3
6
9
15
15
23
21
21 66
42
17
19
57
23
2
10
20

11
21. Attach the Medium Cable (58) to a Small ÒUÓ-
Bracket (71) with a 1/4Ó Nylon Locknut (2)
and a 1/4Ó Flat Washer (10). Do not tighten
the 1/4Ó Nylon Locknut. It should be
threaded onto the Cable only a couple of
turns.
Attach the Small ÒUÓ-Bracket (71) to the indi-
cated Weight Tube (63) with a 5/16Ó x 1 3/4Ó
Bolt (24) and a 5/16Ó Nylon Locknut (3).
22. Locate the Long Cable (72). Attach the Long
Cable to the other Small ÒUÓ-Bracket (71) with
a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat
Washer (10). Do not tighten the 1/4Ó Nylon
Locknut. It should be threaded onto the
Cable only a couple of turns.
Attach the Small ÒUÓ-Bracket (71) to the indi-
cated Weight Tube (63) with a 5/16Ó x 1 3/4Ó
Bolt (24) and a 5/16Ó Nylon Locknut (3).

12
23. Route the Long Cable (72) around the 3 1/2Ó
Pulley (15) on the Top Frame (55). Tighten
the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó
Bolt (not shown).
See inset drawing. Wrap the Long Cable (72)
around a 3 1/2Ó Pulley (15). Attach the Pulley
and a Cable Trap (66) to the bracket on the
Stabilizer (5) with a 3/8Ó x 2Ó Bolt (12) and a
3/8Ó Nylon Locknut (21). Be sure that the
Cable Trap is turned to hold the Cable in
place.
24. Wrap the Long Cable (72) around a 3 1/2Ó
Pulley (15). Attach the Pulley and a Cable
Trap (66) to the Squat Arm (84) with the 3/8Ó
x 2 1/4Ó Bolt (94) and a 3/8Ó Jam Nut (92). Be
sure that the 3/8Ó Jam Nut is on the side
shown and that the Cable Trap is posi-
tioned to hold the Cable in place.

13
25. See inset drawing A. Note: The inset draw-
ing shows the view from the other side of
the Squat Arm Upright (56). Wrap the Long
Cable (72) around a ÒVÓ-Pulley (50). Attach
the ÒVÓ-Pulley and a Long Cable Trap (31) to
the top hole in the Squat Arm Upright with the
3/8Ó x 5Ó Bolt (67), the 5/8Ó x 3/8Ó Spacer (76),
a 3/8Ó Flat Washer (9), and a 3/8Ó Nylon
Locknut (21). Position the Long Cable Trap
(31) as shown.
See inset drawing B. Note: The inset draw-
ing shows the view from the other side of
the Squat Arm Upright (56). Slide the end of
the Long Cable (72) onto the end of the 3/8Ó x
2 1/4Ó Bolt (94). Thread another 3/8Ó Jam Nut
(92) onto the Bolt. Do not tighten the sec-
ond Jam Nut. There must be room
between the two Jam Nuts for the end of
the Cable to pivot.
26. Attach the Backrest (41) to the Front Upright
(42) with two 1/4Ó x 2 1/2Ó Screws (43) and
two 1/4Ó Flat Washers (10).
27. Press a 1 1/2Ó Inner Cap (32) into the Seat
Frame (36).
Insert a 1/4Ó x 2Ó Carriage Bolt (38) through
the center hole in the Seat Plate (37). Attach
the Seat Plate to the Seat (13) with two 1/4Ó x
3/4Ó Screws (18).
Insert the 1/4Ó x 2Ó Carriage Bolt (38) through
the indicated hole in the Seat Frame (36).
Tighten a 1/4Ó Nylon Locknut (2) with a 1/4Ó
Flat Washer (10) onto the Carriage Bolt.
Attach the other end of the Seat (13) to the
Seat Frame (36) with a 1/4Ó Flat Washer (10)
and a 1/4Ó x 2Ó Machine Screw (81).
27
25
26
CABLE ASSEMBLYSEAT ASSEMBLY
67
31
50
50
A
B
76
9
72
92
94
42
41
43 10
13
38
37 32
18
36
2
10
81
72
72
Insets show view
from other side
56
21

14
28. Press a 1 1/2Ó Inner Cap (32) into the Leg
Lever (29).
Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach
the Leg Lever (29) to the Seat Frame (36)
with the 5/16Ó x 2 1/4Ó Bolt and a 5/16Ó Nylon
Locknut (3).
Insert the 5/16Ó x 2Ó Eyebolt (35) into the Leg
Lever (29) from the direction shown. Tighten
a 5/16Ó Nylon Locknut (3) with a 5/16Ó Flat
Washer (8) onto the Eyebolt.
29. Rest the Seat Frame (36) on the indicated pin
in the Front Upright (42). Attach the Seat
Frame to the Front Upright with a 5/16Ó x
2 3/4Ó Carriage Bolt (14) and the Seat Knob
(40).
30. Press two 3/4Ó Round Inner Caps (34) into
each 13 1/2Ó Pad Tube (28).
Insert one 13 1/2Ó Pad Tube (28) into the
Seat Frame (36). Slide a 6Ó Pad (30) onto
each end of the Pad Tube.
Insert the other 13 1/2Ó Pad Tube (28) into the
Leg Lever (29). Slide a 6Ó Foam Pad (30)
onto each end of the Pad Tube.
31. Press 1 1/2Ó Inner Caps (32) into the ends of
the Left VKR Arm (79) and the Right VKR
Arm (80).
Attach the Left VKR Arm (79) and the Right
VKR Arm (80) to the VKR Upright (74) with
two 5/16Ó x 3Ó Bolts (75) and two 5/16Ó Nylon
Locknuts (3).
31
28
29
30
SEAT ASSEMBLYVKR ASSEMBLY
36
3
33ÑLubricate
35
29
8
3
32
42
40
36
36
34
30
34
29
74
79
32
3
75
80
30
28
14
Pin

32. Wet the handle on the Right VKR Arm (80)
with soapy water. Slide a 5Ó Plastic Grip (83)
onto the Handle. Press a 1Ó Round Inner Cap
(49) into the bottom of the handle.
Attach a 5Ó Plastic Grip (83) and a 1Ó Round
Inner Cap (49) to the handle on the Left VKR
Arm (79) in the same manner.
33. Attach a VKR Armrest (78) to the Right VKR
Arm (80) with two 1/4Ó x 2Ó Machine Screws
(81) and two 1/4Ó Flat Washers (10).
Attach a VKR Armrest (78) to the Left VKR
Arm (79) in the same manner.
Attach the VKR Backrest (77) to the VKR
Upright (74) with two 1/4Ó x 2 1/2Ó Screws
(43) and two 1/4Ó Flat Washers (10).
34. Remove the decals from the Decal Sheet (not
shown) and apply them to the home gym sys-
tem in the locations shown:
A Ñ8530
B ÑHIGH PULLEY
C ÑBUTTERFLY
D ÑMILITARY PRESS
E ÑSQUAT STATION
F ÑBENCH PRESS
GÑLEG DEVELOPER
H ÑLOW PULLEY
I ÑVKR
Make sure that all parts have been properly tight-
ened. The use of the remaining parts will be
explained in HOW TO USE THE HOME GYM
SYSTEM, beginning on page 16 of this manual.
Before using the home gym system, pull each
cable a few times to be sure that the cables move
smoothly over the pulleys. If one of the cables
does not move smoothly, find and correct the
problem. IMPORTANT: If the cables are not
properly installed, they may be damaged when
heavy weight is used. See the CABLE DIA-
GRAM on page 19 of this manual for proper
cable routing. If there is any slack in the
cables, the cables should be tightened. See
TROUBLE-SHOOTING AND MAINTENANCE on
page 18.
32
33
34
VKR ASSEMBLY
DECALS
78
74
80
43
79
78
77
81
10
A
B
C
D
E
F
G
H
I
15
79
80
49
83
83
10

16
HOW TO USE THE HOME GYM SYSTEM
The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise
poster accompanying this manual to see how the home gym system should be set up for each exercise.
IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor-
rect starting position for the exercise to be performed. If there is any slack in the cables or chain as an
exercise is performed, the effectiveness of the exercise will be reduced.
58
39
52
53
53
54
26
26
25
25
53
52
23
53
54
CHANGING THE WEIGHT SETTING
The WEIDER 8530 features two weight stacks. The
front weight stack is connected to the upper and
lower pulleys, the press arm, and the butterfly arms.
The rear weight stack is connected to the squat arm.
To change the weight setting of either weight stack,
insert a Weight Pin (26) under the desired Weight
(25). Insert the Weight Pin until the bent end of the
Weight Pin is touching the Weights, and turn the bent
end downward. The weight setting of either weight
stack can be changed from 6.5 pounds to 106.5
pounds, in increments of 12.5 pounds. Note: Due to
the cables and pulleys, the actual amount of
resistance at each exercise station may vary from
the weight setting. Use the WEIGHT RESISTANCE
CHART on page 17 to find the approximate
amount of resistance at each weight station.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE HIGH PULLEY STATION
Attach the Lat Bar (54) to the Medium Cable (58) with
a Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the
Medium Cable with two Cable Clips. Adjust the
length of the Chain between the Lat Bar and the
Medium Cable so the Lat Bar is in the correct
starting position for the exercise to be performed.
The Nylon Strap (39) can be attached in the same
manner.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE LOW PULLEY STATION
Attach the Lat Bar (54) to the Short Cable (23) with a
Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the
Short Cable with two Cable Clips. Adjust the length
of the Chain between the Lat Bar and the Short
Cable so the Lat Bar is in the correct starting
position for the exercise to be performed.
The Nylon Strap (39) can be attached in the same
manner.
39

17
ATTACHING AND REMOVING THE SEAT
To attach the Seat (13), set the bracket on the Seat
Frame (36) onto the indicated pins on the Front
Upright (42). Attach the Seat Frame to the Front
Upright with the 5/16Ó x 2 3/4Ó Carriage Bolt (14) and
the Seat Knob (40).
For some exercises, the Seat (13) must be removed.
First, be sure that the chain is not attached to the leg
lever. Next, remove the Seat Knob (40) and the 5/16Ó
x 2 3/4Ó Carriage Bolt (14) from the Seat Frame (36).
Lift the Seat Frame off the Front Upright (42).
ATTACHING THE LEG LEVER TO THE LOW
PULLEY STATION
To use the Leg Lever (29), the seat must be attached
to the front upright (see ATTACHING AND REMOV-
ING THE SEAT above.)
Attach one end of the Chain (52) to the Short Cable
(23) with a Cable Clip (53). Attach the other end of
the Chain to the Eyebolt (35) with a Cable Clip.
36 13
40
14
42
29
53
35
23
53
52
WEIGHT RESISTANCE CHART
This chart shows the approximate weight resistance at each station. ÒTopÓ refers to the 6.5 lb. top weight. The
other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each
butterfly arm.
WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEY SQUAT ARM
PLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)
To p 2 0 1 0 1 5 1 4 2 4 3 1
145 22 36 28 54 52
270 33 54 44 82 75
3 99 42 75 60 115 101
4 128 48 96 72 147 114
5 153 60 115 90 175 136
6 184 69 137 103 209 157
7 204 79 146 126 223 174
8 247 91 176 138 269 194

TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The
home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there
is slack in the cables before resistance is felt, the cables should be tightened.
Tightening the Medium and Short Cables
If any slack is felt when using the front weight stack,
both the Medium Cable (58) and the Short Cable (23)
will need to be tightened. Insert the weight pin into
the middle of the weight stack. Slack can be removed
from these cables three ways:
¥ See drawing 1. Tighten the 1/4Ó Nylon Locknut
(2) that connects the end of the Short Cable (23)
to the Long ÒUÓ-Bracket (57).
¥ See drawing 1. Move the 3 1/2Ó Pulley (15) to the
other hole in the Long ÒUÓ-Bracket (57). Remove
the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó Bolt
(12) from the Cable Trap (66), Pulley, and Long
ÒUÓ-Bracket. Re-attach the Pulley and Cable
Trap. Be sure that the Cable Trap is in the proper
position and that the Cable and Pulley move
smoothly.
¥ See drawing 2. Tighten the 1/4Ó Nylon Locknut
(2) that connects the end of the Medium Cable
(58) to the Small ÒUÓ-Bracket (71).
Tightening the Long Cable
If any slack is felt when using the rear weight stack,
the Long Cable (72) will need to be tightened. Insert
the weight pin into the middle of the weight stack.
Slack can be removed from these cables two ways:
¥ See drawing 2. Tighten the 1/4Ó Nylon Locknut
(2) that connects the end of the Long Cable (72)
to the Small ÒUÓ-Bracket (71).
¥ See drawing 3. Move the ÒVÓ-Pulley (50) to
another hole in the Squat Arm Upright (56).
Remove the 3/8Ó Nylon Locknut (21) and the 3/8Ó
x 5Ó Bolt (not shown) from the Long Cable Trap
(not shown), and Pulley. Re-attach the Pulley and
Cable Trap. Be sure that the Cable trap is in the
proper position and that the Cable and Pulley
move smoothly.
Do not overtighten the cables. The top weight will
be lifted off the weight stack.
Note: If a cable tends to slip off the pulleys often,
the cable may have become twisted. Remove the cable and re-install it.
If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.
18

19
CABLE DIAGRAM
The cable diagram below shows the proper routing of the Long Cable (72), the Medium Cable (58), and the
Short Cable (23). Use the diagram to be sure that the three cables and cable traps have been assembled cor-
rectly. If the cables have not been correctly routed, the home gym system will not function properly and damage
may occur. The insets show the proper positioning of the cable traps. The cable traps should be positioned so
that the cables will not come off the pulleys. Be sure that the cable traps do not touch or bind the cables.
Short Cable (23)
Long Cable (72)
Medium
Cable (58)
1ÑRear Weight
Stack
2
3
1 ÑLow Pulley
2
3
4
5 ÑLong ÒUÓ-Bracket
TOP VIEW
1 ÑHigh Pulley
2
3
4
7
6
8 ÑFront Weight
Stack
5
4
5ÑThis side of Pulley
must be against the
Squat Arm Upright
6Ñ Squat Arm
Bracket

PART LISTÑModel No. WESY85301 R0100A
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice.
Key No. Qty. Description
1 6 5/16Ó x 2 1/2Ó Carriage Bolt
2 4 1/4Ó Nylon Locknut
3 27 5/16Ó Nylon Locknut
4 1 Base
5 1 Stabilizer
6 1 1Ó Inner Cap
7 1 5/8Ó x 9/16Ó Spacer
8 9 5/16Ó Flat Washer
9 4 3/8Ó Flat Washer
10 13 1/4Ó Flat Washer
11 6 5/16Ó x 2 3/4Ó Bolt
12 6 3/8Ó x 2Ó Bolt
13 1 Seat
14 1 5/16Ó x 2 3/4Ó Carriage Bolt
15 10 3 1/2Ó Pulley
16 1 3/8Ó x 3 1/2Ó Bolt
17 1 Press Frame
18 2 1/4Ó x 3/4Ó Screw
19 4 Weight Bumper
20 1 Pulley Bracket
21 16 3/8Ó Nylon Locknut
22 6 5/16Ó x 2 1/2Ó Bolt
23 1 Short Cable
24 2 5/16Ó x 1 3/4Ó Bolt
25 16 Weight
26 2 Weight Pin
27 5 2Ó Inner Cap
28 2 13 1/2Ó Pad Tube
29 1 Leg Lever
30 4 6Ó Pad
31 4 Long Cable Trap
32 4 1 1/2Ó Inner Cap
33 1 5/16Ó x 2 1/4Ó Bolt
34 4 3/4Ó Round Inner Cap
35 1 5/16Ó x 2Ó Eyebolt
36 1 Seat Frame
37 1 Seat Plate
38 1 1/4Ó x 2Ó Carriage Bolt
39 1 Nylon Strap
40 1 Seat Knob
41 1 Backrest
42 1 Front Upright
43 4 1/4Ó x 2 1/2Ó Screw
44 6 1 3/4Ó Inner Cap
45 2 10Ó Pad
46 2 Press Arm
47 1 Left Arm
48 1 Right Arm
49 2 1Ó Round Inner Cap
Key No. Qty. Description
50 4 ÒVÓ-Pulley
51 2 2Ó Outer Cap
52 1 Chain
53 2 Cable Clip
54 1 Lat Bar
55 1 Top Frame
56 1 Squat Arm Upright
57 1 Long ÒUÓ-Bracket
58 1 Medium Cable
59 1 3/8Ó x 8Ó Bolt
60 2 5/16Ó x 6Ó Bolt
61 4 1/2Ó x 3/4Ó Spacer
62 2 Long Weight Guide
63 2 Weight Tube
64 2 Weight Tube Bumper
65 2 Top Weight
66 7 Cable Trap
67 1 3/8Ó x 5Ó Bolt
68 1 5/16Ó x 5Ó Bolt
69 4 1Ó Retainer
70 2 1Ó Round Cover Cap
71 2 Small ÒUÓ-Bracket
72 1 Long Cable
73 2 Short Weight Guide
74 1 VKR Upright
75 2 5/16Ó x 3Ó Bolt
76 1 5/8Ó x 3/8Ó Spacer
77 1 VKR Backrest
78 2 VKR Armrest
79 1 Left VKR Arm
80 1 Right VKR Arm
81 5 1/4Ó x 2Ó Machine Screw
82 2 Handle
83 8 5Ó Plastic Grip
84 1 Squat Arm
85 2 Squat Arm Pad
86 3 3/8Ó x 2 1/2Ó Bolt
87 2 1Ó x 2Ó Inner Cap
88 4 3/8Ó x 3 3/4Ó Bolt
89 2 1 1/4Ó x 2 1/2Ó Plastic Bushing
90 2 1Ó x 7/8Ó Plastic Bushing
91 2 1/2Ó x 17/32Ó Spacer
92 2 3/8Ó Jam Nut
93 1 3/8Ó x 5 1/2Ó Bolt
94 1 3/8Ó x 2 1/4Ó Bolt
95 1 3 1/2Ó Low Pulley
96 2 Inner Cap
# 1 UserÕs Manual
# 1 Exercise Poster