Weiler E2850 Installation instructions

WEILER E2850 REMIXING TRANSFER VEHICLE
E2850
Remixing Transfer
Vehicle
Operator’s and Maintenance
Manual
July 2018
S/N 1001 - UP
Part No. 18183

WEILER E2850 REMIXING TRANSFER VEHICLE
WEILER WARRANTY
-Exclusive Limited Warranty-
The manufacturer warrants each new WEILER PRODUCT to be free of defects in workmanship and
material at the time of shipment to first end-user. The warranty period is 12 months.
A. If a defect is found, and the authorized dealer is notified during the 12 month warranty period, the
manufacturer will repair or replace any part or component on the unit that fails to conform to the
warranty.
B. The manufacturer has the right to repair any part or component prior to replacement.
C. All new replacement parts will carry a six (6) month warranty. Remanufactured parts will carry a
ninety (90) day warranty.
D. ENGINES, TIRES, BATTERIES and ATTACHMENTS are normally warranted by their
manufacturers and may have different warranty than that of the manufacturer.
NO WARRANTY OF ANY KIND SHALL BE MADE WITH RESPECT TO:
A. Any defects or damage caused by misuse, misapplication, negligence accident or failure to maintain
or use the product in accordance with current operating instructions.
B. Any product that has been used with an attachment or in an application where excessive workload or
stress causes failure of the part or component.
C. Failure to conduct normal maintenance and operating service to include but not limited to providing
lubricants, coolant, fuel, inspections and regular tune-ups.
D. Unauthorized alterations, modifications and or replacements parts and components not manufactured
by the manufacturer.
THE MANUFACTURER IS NOT RESPONSIBLE FOR THE FOLLOWING:
A. Charges for travel time, mileage or overtime.
B. Airfreight charges for parts shipped to point of service.
C. Transportation charges to and from point of service.
D. Consumable parts such as cutting edges, filters and items expected to receive normal wear and tear.
E. Liability or damages of any type due to lost profits or expenses to acquire replacement products
EXCEPT AS SPECIFICALLY STATED ABOVE, THE MANUFACTURER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE
WARRANTY SET FORTH ABOVE AND THE OBLIGATIONS AND LIABILITIES OF THE
MANUFACTURER THEREUNDER REPRESENT CUSTOMER’S SOLE AND EXCLUSIVE
REMEDIES AND ARE EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER REMEDIES,
WARRANTIES, GUARANTIES OR LIABILITIES. THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT SHALL THE
MANUFACTURER’S LIABILITY HEREUNDER EXCEED THE PURCHASE PRICE FOR THE
PRODUCTS, NOR SHALL THE MANUFACTURER BE LIABLE FOR ANY SPECIAL INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
10/21/05

WEILER E2850 REMIXING TRANSFER VEHICLE
i
Product and Dealer Information
PRODUCT AND DEALER INFORMATION
Delivery Date:_______________________________
DEALER INFORMATION
Dealer Name_________________________________________________________________________________
Address_____________________________________________________________________________________
City_________________________________________________________________________________________
State__________________________________________ Zip / Post Code________________________________
Country_______________________________________ Phone________________________________________
OWNER INFORMATION
Owner Name_________________________________________________________________________________
Address_____________________________________________________________________________________
City_________________________________________________________________________________________
State_________________________________________ Zip / Post Code_________________________________
Country______________________________________ Phone_________________________________________
MACHINE IDENTIFICATION NUMBERS
Engine Model Number________________________________________________________________________
Engine Serial Number________________________________________________________________________
Machine Model Number_______________________________________________________________________
Machine Product Identification Number________________________________________________________

WEILER E2850 REMIXING TRANSFER VEHICLE
ii Receiving and Delivery Report
RECEIVING AND DELIVERY REPORT
DEALER PREP
Check or perform the following:
General
____ Check machine for shipping damage or shortage.
____ Check that all optional and loose items are included with machine.
____ Check that all safety signs and control decals are not damaged.
____ Check that the Operator's and Maintenance Manual is attached to machine.
____ Check neutral start system and engine stop operations.
____ Check for fluid leaks. If leak is found, correct leak and check component fluid level.
Engine/Drivetrain
____ Check fuel level.
____ Check oil level.
____ Check coolant level.
Hydraulics
____ Check fluid level.
____ Check for proper function.
DELIVERY
Check and perform the following with the operator/owner:
Machine
____ Review all sections of this Operator’s and Maintenance Manual.
____ Fill out Dealer, Owner, and Machine information sections in this manual.
Review of Operation
____ Overall explanation and demonstration of how the machine works.
____ Explain machine and operator safety.
____ Preparing machine for operation.

WEILER E2850 REMIXING TRANSFER VEHICLE
iii
TABLE OF CONTENTS
Product and Dealer Information . . . . . . . . . . . . i
Receiving and Delivery Report . . . . . . . . . . . . ii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . iii
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . viii
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . viii
SAFETY
Safety Messages . . . . . . . . . . . . . . . . . . . . .1-1
General Safety Rules . . . . . . . . . . . . . . . . . .1-4
Check Laws and Regulations . . . . . . . . . . . .1-4
Fire Extinguisher. . . . . . . . . . . . . . . . . . . . . .1-5
Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . .1-5
MACHINE CONTROLS
Machine Description. . . . . . . . . . . . . . . . . . .2-1
Machine Terminology . . . . . . . . . . . . . . . . .2-2
Machine Controls . . . . . . . . . . . . . . . . . . . . .2-3
OPERATING INSTRUCTIONS
Operator Qualifications. . . . . . . . . . . . . . . . .3-1
Personal Protection . . . . . . . . . . . . . . . . . . .3-1
Sound Levels . . . . . . . . . . . . . . . . . . . . . . . .3-2
Vibration Levels . . . . . . . . . . . . . . . . . . . . . .3-2
Prepare the Area . . . . . . . . . . . . . . . . . . . . .3-3
Mounting and Dismounting. . . . . . . . . . . . . .3-4
Pre-Starting Inspection (Before Each Use) .3-5
Machine Starting Procedure . . . . . . . . . . . . .3-6
Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . .3-8
Machine Starting Procedure - Cold Start . . .3-9
Machine Shutdown Procedure . . . . . . . . . .3-11
Preparing Machine . . . . . . . . . . . . . . . . . . .3-13
Driving Machine . . . . . . . . . . . . . . . . . . . . .3-30
Paving. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-32
Machine Cleanup . . . . . . . . . . . . . . . . . . . .3-45
TRANSPORTING
Preparing for Transport . . . . . . . . . . . . . . . .4-1
Lifting Machine . . . . . . . . . . . . . . . . . . . . . . .4-2
Roading Machine . . . . . . . . . . . . . . . . . . . . .4-2
Towing/Retrieving Machine . . . . . . . . . . . . .4-3
Trailering Machine . . . . . . . . . . . . . . . . . . . .4-8
MAINTENANCE
Safety Messages . . . . . . . . . . . . . . . . . . . . . 5-1
Safety Signs. . . . . . . . . . . . . . . . . . . . . . . . . 5-2
General Information . . . . . . . . . . . . . . . . . . . 5-3
Welding Precautions . . . . . . . . . . . . . . . . . . 5-4
Engine Maintenance . . . . . . . . . . . . . . . . . . 5-5
Maintenance Schedule . . . . . . . . . . . . . . . . 5-7
Maintenance Procedures . . . . . . . . . . . . . . . 5-8
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-61
SPECIFICATIONS
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Performance Specifications . . . . . . . . . . . . .A-2
Engine Specifications. . . . . . . . . . . . . . . . . .A-3
Hydraulic System Specifications . . . . . . . . .A-5
FAULT CODES
Electronic Display Error Fault Codes . . . . . .B-1
SCHEMATICS
Electrical Schematic – S/N 1001–1063 . .C-1
Electrical Schematic – S/N 1064–1094 . . .C-7
Electrical Schematic – S/N 1095–1121 . . .C-14
Electrical Schematic – S/N 1122–1140 . .C-21
Electrical Schematic – S/N 1141–1144 . . .C-28
Electrical Schematic – S/N 1144–1149
(Includes Australia Machine) . . . . . . . .C-35
Electrical Schematic – S/N 1150–1153 . . .C-44
Electrical Schematic – S/N 1154–UP . . . .C-53
Hydraulic Schematic . . . . . . . . . . . . . . . . .C-62

This page intentionally left blank.

WEILER E2850 REMIXING TRANSFER VEHICLE
vii
Foreword
FOREWORD
This manual is an important part of the machine and provides correct procedures for machine
operation and maintenance. Proper maintenance and service are essential for safety and for efficient
operation of the machine. Do not use the machine if it is not in suitable operating condition. Read and
understand these instructions thoroughly before operating the machine for the first time or
maintaining machine. Failure to do so could result in personal injury or equipment damage. Contact
an authorized Weiler dealer if you do not understand the instructions in this manual or need
additional information.
This tethered manual must remain with the machine at all times. Store it in the manual box.
Replace manual immediately if lost, damaged, or unreadable. If you sell the machine, be sure this
manual is transferred to the new owner.
If a question arises concerning the equipment, contact an authorized Weiler dealer. Factory-trained
personnel and genuine replacement parts are available for all service requirements.
To maintain and help ensure trouble-free operation of this machine, the routine maintenance as
specified in this manual must be carried out at the recommended intervals.
The instructions, illustrations, and specifications in this manual are based on the latest information
available at time of publication. This machine may have product improvements and features not yet
contained in this manual. Dimensions and weights are approximate and the illustrations may not
show the equipment in standard configuration.
The following acronyms may be used throughout this manual: CAN - Controller Area Network, CW -
Clockwise, CCW - counterclockwise, DEF - Diesel Exhaust Fluid, DOC - Diesel Oxidation Catalyst,
DPF - Diesel Particulate Filter, ECM - Electronic Control Module, LCD - Liquid Crystal Display,
LED - Light Emitting Diode, PPE - Personal Protective Equipment, SMV - Slow Moving Vehicle, and
SCR - Selective Catalytic Reduction.
Make no modifications to machine unless specifically requested or authorized by Weiler. Modification
of this machine could mean that it will no longer meet applicable standards or regulations, and the
machine may not function properly or in accordance with these operating instructions. Machine
modification should only be performed and verified for operational and safety requirements by
competent personnel.
Weiler reserves the right to make changes at any time without notice or obligation.
This equipment may be covered by one or more U.S. patents listed at
www.weilerproducts.com/patents.

WEILER E2850 REMIXING TRANSFER VEHICLE
viii Introduction
INTRODUCTION
Thoroughly read and understand these instructions and store the tethered manual in the manual
holder on the machine for future reference.
When purchasing a used Weiler machine you are requested to contact Weiler Customer Service at
www.weilerproducts.com and request a customer login and password to gain access to online
manuals for this machine.
Additional copies of the manuals are available from an authorized Weiler dealer. When ordering a
new manual, use the part number on the front cover.
INTENDED USE
The E2850 Remixing Transfer Vehicle is used to transfer bulk asphalt paving material from delivery
vehicles to a paving machine. The machine receives paving material in the forward dump hopper, or
picks windrowed material up off of the roadway, delivers the material to the center hopper for
remixing, and then conveys the material to the hopper of a paving machine.
Always use the machine in accordance with the instructions contained in this Operator's and
Maintenance Manual, safety signs on the machine, and other material provided by Weiler. Usage in
any other way is considered contrary to the intended use.
Proper maintenance and repair are essential for safety and for efficient operation of the machine. Do
not use the machine if it is not in suitable operating condition.
This safety alert system identifies important safety messages in this
manual.
When you see this symbol, be alert, your safety is involved, carefully read
the message that follows, and inform other operators.

WEILER E2850 REMIXING TRANSFER VEHICLE
1-1
Safety 1
Safety Messages
SECTION 1: SAFETY
SAFETY MESSAGES
General safety messages appear in the Safety Messages section. Specific safety messages are located
in appropriate sections of the manual where a potential hazard may occur if the instructions or
procedures are not followed.
Personal Safety
A signal word “DANGER”, “WARNING”, or “CAUTION” is used with the safety alert symbol.
Safety signs with signal word “DANGER”, “WARNING”, or “CAUTION” are located near specific
hazards.
Machine or Property Damage
The signal word ˆNOTICE˜ is not used with a safety alert symbol and is followed by specific
instructions.
Decals with the signal word ˆNOTICE˜ are located near specific areas where machine or property
damage may occur.
DANGER indicates a hazardous situation that, if not avoided, will result in
death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result
in minor or moderate injury.
This is the safety alert symbol. This symbol is used in combination with an
exclamation mark or other symbols to alert you to the potential for bodily
injury or death.
NOTICE indicates information considered important, but not hazard related.
It is used to inform about possible machine and/or property damage.
This symbol indicates that machine damage may occur if proper procedures
are not followed, or at least one part of the machine is not operating correctly.
Shutting down machine may not be necessary, but some maintenance may be
required.
DANGER
WARNING
CAUTION
NOTICE

1
WEILER E2850 REMIXING TRANSFER VEHICLE
1-2
Safety
1
Safety Messages
Refer to "Machine Shutdown Procedure", page 4-9, for instructions.
WARNING
Read Operator’s and Maintenance Manual and safety signs before operating
machine.
WARNING
Check machine before operating. Machine must be in good operating
condition and all safety equipment installed and functioning properly.
WARNING
Wear personal protective equipment (PPE). Dress properly. Wear close-
fitting clothing and confine long hair. Avoid wearing jewelry, such as
rings, wristwatches, necklaces, or piercings. Refer to “Personal Protective
Equipment” in the Operator’s and Maintenance sections of this manual
for additional requirements.
WARNING
Follow Shutdown Procedure before inspecting, fueling, cleaning,
transporting, lubricating, repairing, or servicing machine.
WARNING
Make sure no one is working on, underneath, or close to the machine
before starting the engine or moving the machine. Make sure the area is
free of personnel. Keep spectators away.
WARNING
Falling load can crush and cause death or serious injury.
Never work under lifted load unless load is securely supported to prevent
falling.

WEILER E2850 REMIXING TRANSFER VEHICLE
1-3
Safety 1
Safety Messages
WARNING
Pressurized fluid can penetrate body tissue and result in death or serious
injury. Leaks can be invisible. Keep away from any suspected leak. Relieve
pressure in the hydraulic system before searching for leaks, disconnecting
hoses, or performing any other work on the system. When searching for a
pressurized leak, use an object such as a piece of wood or cardboard. Keep
hands away. When loosening a fitting where residual pressure may exist,
slowly loosen fitting until oil begins to leak. Wait for leaking to stop before
disconnecting fitting. Tighten all connections before re-pressurizing system.
Seek immediate surgical treatment if fluid is injected under the skin.
WARNING
Contact with moving parts can cause death or serious injury.
Keep hands, feet, and clothing away from power-driven parts. Keep all
shields and guards in place and properly secured.
CAUTION
Hot asphalt can cause injury from burns.
• Wear safety glasses, gloves, and protective clothing.
• Avoid contact with skin, eyes, and clothing.
In case of skin contact, get prompt medical attention.
WARNING
A rider can fall off and be crushed.
Never allow anyone to ride on the ladder or platform.
WARNING
Engine exhaust can asphyxiate. If inhaled directly or continuously, the
combustion fumes produced by the engine can cause death or serious
injury.
If work has to be done in an enclosed environment, take all necessary
precautions to ensure the circulation of fresh air and protect the
respiratory system using a suitable mask.
WARNING
Breathing crystalline silica dust may cause lung disease. Cutting,
drilling, or working materials such as concrete, sand, or rock containing
quartz may result in exposure to silica dust.
Use dust control methods or appropriate respirator protection when
exposed to silica dust conditions.

1
WEILER E2850 REMIXING TRANSFER VEHICLE
1-4
Safety
1
General Safety Rules
GENERAL SAFETY RULES
The following safety rules are important for safe operation of the machine. Remember that no amount
of safety rules or safety equipment can make the operation of any machine safe, unless the operator
follows the rules and uses the safety equipment.
•Only a responsible, properly trained safety-conscious individual should operate the machine.
•The operator should not leave the operator’s platform when the engine is running.
•Always keep the operator’s platform and ladder clean and free of debris to help prevent slipping
and falling.
•Stay clear of wheels, conveyors/augers, and hopper(s) when engine is running.
•Place all controls in neutral or off position and apply park brake before starting machine and
shutting machine down.
•Never place body between machine and truck, or machine and paver.
•Provide appropriate lighting and marking on the machine to meet jobsite requirements and
regulations.
•Be sure safety shields and guards are in place and in good condition before starting the machine.
•Before cleaning, adjusting, or servicing machine, turn engine off and place all controls in neutral
or off position and apply park brake. Lower all attachments, or securely support raised
components. A variation of the above procedure may be used if instructed within this manual.
CHECK LAWS AND REGULATIONS
Know and obey all federal, state, and local laws and regulations that apply to your work situation.
WARNING
Failure to follow any of the safety instructions within this manual could
result in death or serious injury. This machine is to be used only for those
purposes for which it was intended as explained in this manual.

WEILER E2850 REMIXING TRANSFER VEHICLE
1-5
Safety 1
Fire Extinguisher
FIRE EXTINGUISHER
Mount a fire extinguisher (not supplied with machine) on the platform near the operating station for
easy access to the operator and near the platform ladder for access to personnel on the ground.
SAFETY SIGNS
Safety Signs - Inspect
Safety signs located on machine contain important and useful information that will help you operate
the machine safely. Refer to "Safety Signs", page 5-2, for safety sign maintenance and replacement.

1
WEILER E2850 REMIXING TRANSFER VEHICLE
1-6
Safety
1
Safety Signs
Safety Sign Locations
Slip and fall hazard.
Keep platform clean.
25649 JQRRGTNKHVGF
UYKPIEQPXG[QTYKVJ
KPUGTV&QPQVFTKXGQT
.KHVQPN[9GKNGTJQRRGT
<2600 lb <1180 kg
WARNING
(CNNKPINQCFECPETWUJ

CBA-46-2320
Moving parts can crush.
Keep hands and feet
away.
ON STORAGE HOPPER CLEANOUT DOORS
CBA-46-2320
Moving parts can crush.
Keep hands and feet
away.
BOTH SIDES
BOTH SIDES
23652
Crush Hazard
Keep hands away.
BOTH SIDES
23652
Crush Hazard
Keep hands away.
BOTH SIDES
CBA-46-2320
Moving parts can crush.
Keep hands and feet
away.
BOTH SIDES
INSIDE ENGINE COMPARTMENT
Allow to cool before opening.
36515
Hot fluid under pressure
can scald.
V2326324
Fuel and fumes can
explode and burn.
STOP
Stop engine. No flame.
No smoking.
ON END OF CONVEYOR

WARNING
(CNNKPINQCFECPETWUJ ECDNGU4GCF1RGTCVQTU/CPWCN
<1180 kg
<2600 lb
7UGQPN[RTQRGTN[TCVGFEJCKPUQT
.KHVQPN[9GKNGTJQRRGTKPUGTV
18398
Moving conveyor slats.
Keep hands out.
WARNING
18398
Moving conveyor slats.
Keep hands out.
WARNING
To lock platform, lift handle, rotate pin off of catch, and release. Center platform until platform catches in lock mechanism. To unlock platform, lift handle, rotate pin onto catch, and release.
13883
Platform must be centered and locked for transport.
CAUTION

5VC[CYC[HTQO
GPGTIK\GFRQYGTNKPGU
DANGER
FGCVJQTUGTKQWUKPLWT[
'NGEVTKEUJQEMYKNNECWUG
WARNING
31859
Read
Operator’s Manual Safety message.
WARNING
18877
Stop engine before servicing. Safety message.
%QPVCEVYKVJOQXKPI -GGRIWCTFUKPRNCEG
-GGRJCPFUCYC[
RCTVUECPETWUJQTEWV
%'ÄÄ
WARNING
Slip and fall hazard.
sloped surface. Do not walk on
18359
WARNING
CD462333
Moving parts can crush. Stay away.
CD462333
Moving parts can crush. Stay away.
BOTH SIDES
9123
Runover can crush. Keep feet away
from wheels.

WARNING
Rotating auger can cut
or crush. door. Stay away from
Auger behind clean-out
rotating auger.

WARNING
Rotating auger can cut
or crush. door. Stay away from
Auger behind clean-out
rotating auger.
WARNING
QTETWUJ
4QVCVKPICWIGTYKNNEWV
TQVCVKPICWIGT
5VC[CYC[HTQO

DANGER

WEILER E2850 REMIXING TRANSFER VEHICLE
1-7
Safety 1
Safety Signs
Safety Sign Explanations
WARNING
Read Operator’s and Maintenance Manual and safety signs before operating
or servicing machine.
Turn engine off and remove ignition key before servicing.
WARNING
Falling load can crush.
Lifting device is designed only to lift approved Weiler hopper inserts. Do
not use to lift any other objects.
WARNING
Moving parts can crush.
Keep hands and feet away from moving parts.
WARNING
Fuel and fumes can explode and burn.
Turn engine off before refueling. No flame. No smoking.
WARNING
Rotating augers can crush or cut of hands.
Auger behind cleanout door. Stay away from rotating augers. Turn engine
off and remove ignition key when servicing or cleaning augers.
WARNING
Death or serious injury possible if crushed between conveyor and frame or
conveyor and ladder.
Stay out of area between conveyor and frame, and conveyor and ladder.
WARNING
Contact with moving parts can cut or crush.
Keep hands, feet, and clothing away from power-driven parts. Turn
engine off and wait for all motion to stop before working on machine. Keep
all shields and guards in place and properly secured.

1
WEILER E2850 REMIXING TRANSFER VEHICLE
1-8
Safety
1
Safety Signs
WARNING
Runover can crush.
Keep feet away from wheels.
WARNING
Moving parts can crush.
Keep hands away from moving parts.
CAUTION
Platform may shift and make machine over width during transport.
Center and lock platform for transport.
WARNING
Hot fluid under pressure can scald.
Allow to cool before opening coolant cap.
DANGER
Entanglement in rotating augers can crush or cut off hands and feet.
Stay away from rotating augers. Turn engine off and remove ignition key
when servicing or cleaning augers.
WARNING
Battery fumes are flammable and can explode. Battery explosion can
blind. Acid can blind and burn.
Keep all burning materials, flame, and sparks away from battery. Tools
and cable clamps can make sparks. Shield eyes and face. Do not smoke.
Avoid breathing fumes. Work in well ventilated area. Read instructions.
WARNING
Slippery surfaces may cause you to slip and fall.
Keep walkways, platforms, and ladders clean.

WEILER E2850 REMIXING TRANSFER VEHICLE
1-9
Safety 1
Safety Signs
DANGER
Electric shock possible. Death or serious injury will result from
inadequate clearance or contact with an energized power line.
Stay away from an energized power line. Maintain a clearance of at least
10 ft (3 m) between machine components, including the operator, and any
electrical line carrying up to 50,000 volts (50 kv). Add one additional foot
of clearance for every additional 30,000 volts (30 kv) or less. Allow for
power line sway.
Ground personnel must stay away as machine approaches or is near an
energized power line.
Electric utility provider must de-energize power lines before approaching.
WARNING
Slipping and falling off storage hopper platform may result in death or
serious injury.
• Raise guard rails when entering storage hopper observation platform.
• Do not enter storage hopper observation platform when machine is
moving.
• Always maintain 3-point contact when on service platform. Do not
step onto elevator sloped surfaces.
WARNING
Moving conveyor slats can crush or cut off fingers and hands.
Never reach into conveyor chute or insert a cleanout tool into conveyor
chute when conveyor is moving. Turn engine off before cleaning or
working on conveyor.
WARNING
Falling load can crush.
Stay clear of lifted hopper insert.
WARNING
Read manual for limp mode instructions.

This page intentionally left blank.

WEILER E2850 REMIXING TRANSFER VEHICLE
2-1
Machine Controls 2
Machine Description
SECTION 2: MACHINE CONTROLS
MACHINE DESCRIPTION
The Weiler E2850 is a self-propelled remixing transfer vehicle with storage, used for transferring hot-
mix asphalt from transport vehicles to an asphalt paver during continuous, non-contact paving.
Optional Weiler hopper inserts for the paver provide additional storage capacity.
A shiftable operator platform allows for left or right side operation. All operational functions can be
controlled from the operator platform. Control panels on both sides and at rear of the machine
provide ground control of hopper and cleanout functions. A spray down system is provided for
machine clean-up.
Options available are 10KW generator, work lights, paver hopper insert, truck hitch, steerable rear
axle, windrow attachment, automatic lubrication system, ground speed indicator, conveyor spray
down system, tire spray system, 60 gallon (227 L) spray down tank, camera system, truck signal
lights, and distance-from-paver system.

1
WEILER E2850 REMIXING TRANSFER VEHICLE
2-2
Machine Controls
2
Machine Terminology
MACHINE TERMINOLOGY
(1) Battery Box
(2) Discharge Conveyor
(3) Dump Hopper
(4) Dump Hopper Control Station (each side)
(5) Dump Hopper Lights
(6) Elevator
(7) Engine and Pump Compartment
(8) Front Fume Extractor
(9) Headlamps
(10) Operator Station
(11) Rear Fume Extractor
(12) Storage Hopper
(13) Truck Hitch
(14) Truck Signal Lights (Optional)
(15) Work Lights (each side)
Front
Rear
Right
Left
2
3
12
13
7
8
5
6
1
15
9
11
14
4
10