Well SENS-PIR-C03-WL User manual

USER MANUAL
(PIR motion sensor)
Thank you for choosing WELL. Please read carefully the following instructions and keep them within reach.
Reorder No: SENS-PIR-C03-WL

This product adopts high sensitivity detector, integrated circuit and SMD; It gathers automatic, convenient,
safe, energy-saving, practical functions; It uses human motion infrared rays as a control signal sources,
when someone enters the detection field, it will start the controlled load at once; It can identify day and
night automatically; It is easy to install and its usage is widely
SPECIFICATION:
Power Source: 220-240V/AC Detection Range: 360°
Power Frequency: 50/60Hz Detection Distance: 6m max(<24℃)
Ambient Light: <10-2000LUX (adjustable) Working Temperature: -20~+40℃
Time Delay: Min.10sec±3sec Working Humidity: <93%RH
Max.7min±2min Power Consumption: approx. 0.5W
Rated Load: 1200W (incandescent lamp) Installation Height: 2.2-4m
300W(energy-saving lamp/led lamp) Detection Moving Speed: 0.6-1.5m/s
FUNCTION:
➢Can identify day and night: The consumer can adjust working state in different ambient light. It can
work in the daytime and at night when it is adjusted on the “sun” position (max). It can work in the
ambient light less than 10LUX when it is adjusted on the “moon” position (min).
➢Time-Delay is added continually: When it receives the second induction signals within the first
induction, it will restart to time from the moment.
Good sensitivity Poor sensitivity
INSTALLATION:
As the detector responds to changes in temperature, avoid the following situations:
➢Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
➢Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, light etc.
➢Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants
etc.

CONNECTION:
Warning. Danger of death through electric shock!
⚫Must be installed by professional electrician.
⚫Disconnect power source.
⚫Cover or shied any adjacent live components.
⚫Ensure device cannot be switched on.
⚫Check power supply is disconnected.
➢Turn the bottom-cover anti-clockwise and unload it.
➢The power wire goes across the hole in the middle of bottom-stand. Connect the
power wire into connection-wire column according to the connection-wire
diagram.
➢Fix the bottom-stand on the selected position with the provided screws.
➢The sensor should be aimed at the mouth of bottom-stand and turned clockwise.
➢After finishing installing, turn on the power and then test it.
CONNECTION-WIRE DIAGRAM:
(See the right figure)
SENSOR INFOMATION
Height of installation:2.2-4m
Detection Distance: Max.6m

TEST:
➢Turn the TIME knob anti-clockwise on the minimum (-). Turn the LUX knob anti-
clockwise on the maximum (sun).
➢Switch on the power; the sensor and its connected lamp will have no signal at
the beginning. After Warm-up 30sec, the sensor can start work. If the sensor
receives the induction signal, the lamp will turn on. While there is no another
induction signal any more, the load should stop working within 10sec±3sec and
the lamp would turn off.
➢Turn LUX knob clockwise on the minimum (moon). If the ambient light is more
than 10LUX, the sensor would not work, and the lamp stop working too. If the
ambient light is less than 10LUX (darkness), the sensor would work
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor
lamp could not work! If the lamp is more than 60W, the distance between lamp and sensor should
be 60cm at least.
SOME PROBLEM AND SOLVED WAY:
➢The load does not work:
a. Please check if the connection of power source and load is correct.
b. Please check if the load is good.
c. Please check if the settings of working light correspond to ambient light.
➢The sensitivity is poor:
a. Please check if there is any hindrance in front of the detector to affect it to receive the signals.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required in the instruction.
e. Please check if the moving orientation is correct.
➢The sensor cannot shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is set to the maximum position.
c. Please check if the power corresponds to the instruction.
Waste electrical and electronic equipment are a special waste category,
collection, storage, transport, treatment and recycling are important because
they can avoid environmental pollution and are harmful to health. Submitting
waste electrical and electronic equipment to special collection centers makes
the waste to be recycled properly and protecting the environment. Do not
forget! Each electric appliance that arrives at the landfill, the field, pollutes the
environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*

[email protected]o, www.vitacom.ro