Well SENS-PIR-W01-WL User manual

USER MANUAL
(PIR motion sensor)
Thank you for choosing WELL. Please read carefully the following instructions and keep them within
reach.
Reorder No: SENS-PIR-W01-WL

The product adopts good sensitivity detector and integrated circuit. It gathers automatism, convenience,
safety, saving-energy and practicality functions. The wide detection field consists of up and down, left and
right service field. It works by receiving human motion infrared rays. When someone enters the detection
field, it will start the load at once and it can identify automatically the day and the night. The installation is
very easy and it is used very wide.
SPECIFICATION:
Power Source: 220-240V/AC Detection Range: 180°
Power Frequency: 50/60Hz Detection Distance: 12m max(<24℃)
Ambient Light: <10-2000LUX (adjustable) Working Temperature: -20~+40℃
Time Delay: Min.10sec±3sec Working Humidity: <93%RH
Max.7min±2min Power Consumption: approx 0.5W
Rated Load: Max.1200W (incandescent lamp) Installation Height: 1.8-2.5m
300W(energy-saving lamp/led lamp) Detection Moving Speed: 0.6-1.5m/s
FUNCTION:
➢The product can identify day and night: The consumer can adjust working state in different ambient
light. It can work in the daytime and at night when LUX knob is adjusted on the “sun” position (max). It
can work in the ambient light less than 10LUX when it is adjusted on the “moon” position (min).
➢Time-Delay is added continually: When it receives the second induction signals within the first
induction, it will restart to time from the moment.
Good sensitivity Poor sensitivity
INSTALLATION:
As the detector responds to changes in temperature, avoid the following situations:
➢Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
➢Avoid mounting the detector near heat sources, such as heating vents, air conditioning units, light etc.
➢Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants
etc.

CONNECTION:
Warning. Danger of death through electric shock!
⚫Must be installed by professional electrician.
⚫Disconnect power source.
⚫Cover or shied any adjacent live components.
⚫Ensure device cannot be switched on.
⚫Check power supply is disconnected.
➢Loosen the screw in the back and unload the bottom (refer to figure 1).
➢Find the wire hole in the bottom and pass the power wire through hole. Connect the power wire into
connection-wire column according to the connection-wire diagram..
➢Fix the bottom with the provided screws on the selected position. (refer to figure 2)
➢Install back the sensor on the bottom, tighten the screw and then test it.
Figure1 Figure2
CONNECTION-WIRE DIAGRAM:
(See the right figure)
TEST:
➢Turn the TIME knob anti-clockwise on the minimum (-).Turn the LUX
knob clockwise on the maximum (sun);
➢Switch on the power; the sensor and its connected lamp will have no
signal at the beginning. After Warm-up 30sec, the sensor will start to
work .If the sensor receives the induction signal, the lamp will turn on.
While there is no another induction signal any more, the load will stop
working within 10sec±3sec and the lamp will turn off.
➢Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than 10LUX, the
sensor would not work and the lamp will stop working too. If the ambient light is less than 10LUX
(darkness), the sensor will work. Under no induction signal condition, the sensor should stop working
within 10sec±3sec.
Note: When testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp
will not work! If the lamp is more than 60W, the distance between lamp and sensor should be 60cm at
least.

TROUBLESHOOTING:
➢The load does not work:
a. Please check if the connection of power source and load is correct.
b. Please check if the load is good.
c. Please check if the settings of working light correspond to ambient light.
➢The sensitivity is poor:
a. Please check if there is any hindrance in front of the detector to affect it to receive the signals.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required in the instruction.
e. Please check if the moving orientation is correct.
➢The sensor can not shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is set to the maximum position.
c. Please check if the power corresponds to the instruction.
Waste electrical and electronic equipment are a special waste category,
collection, storage, transport, treatment and recycling are important because
they can avoid environmental pollution and are harmful to health. Submitting
waste electrical and electronic equipment to special collection centers makes
the waste to be recycled properly and protecting the environment. Do not
forget! Each electric appliance that arrives at the landfill, the field, pollutes the
environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
[email protected]o, www.vitacom.ro