Weslo PRO 10.8x User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Serial
Number
Decal
Model No. 831.21832.0
Serial No.
Write the serial number in the
space above for reference.
• Assembly
• Operation
• Maintenance
• Part ist and Drawing
Sears, Roebuck and Co., Hoffman Estates, I 60179
BIKE EXERCISER
Userʼs Manual

2
TAB E OF CONTENTS
WARNINGDECA P ACEMENT ..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMB Y ...............................................................................5
HOWTOUSETHEEXERCISECYC E........................................................11
MAINTENANCEANDTROUB ESHOOTING ...................................................18
EXERCISEGUIDE INES ...................................................................19
PART IST ..............................................................................22
EXP ODEDDRAWING ....................................................................23
ORDERINGREP ACEMENTPARTS ..................................................BackCover
90DAYFU WARRANTY ..........................................................BackCover
WARNING DECA P ACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, call 1-866-699-3756 and
request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.

3
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the exercise cycle are ade-
quately informed of all precautions.
3. Your exercise cycle is intended for home use
only. Do not use your exercise cycle in a
commercial, rental, or institutional setting.
4. Keep your exercise cycle indoors, away from
moisture and dust. Place your exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around your exer-
cise cycle to mount, dismount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your exercise cycle at all times.
7. Your exercise cycle should not be used by
persons weighing more than 250 lbs.
(113 kg).
8. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
9. Wear appropriate exercise clothes while
exercising; do not wear loose clothes that
could become caught on your exercise
cycle. Always wear athletic shoes for foot
protection while exercising.
10. Keep your back straight while using your
exercise cycle; do not arch your back.
11. When you stop exercising, allow the pedals
to slowly come to a stop.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. Use your exercise cycle only as described in
this manual.
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. Sears assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS

4
Thank you for selecting the new WES O PRO™
10.8X exercise cycle. Cycling is one of the most effec-
tive exercises for increasing cardiovascular fitness,
building endurance, and toning the body. The 10.8X
exercise cycle offers a selection of features designed
to let you enjoy this healthful exercise in the conve-
nience and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, please see the back cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Seat
Adjustment Knob
Pedal/Strap
Console
Pulse Sensor
Wheel
Backrest
Fan
Handlebar
BEFORE YOU BEGIN

5
ASSEMB Y
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tools, assembly requires a Phillips screwdriver and an adjustable
wrench .
As you assemble the exercise cycle, use the drawings below to identify the small parts used in assembly. The
number in parentheses below each drawing is the key number of the part, from the PART IST near the end of
this manual. The number following the parentheses is the quantity needed for assembly. Note: Some small
parts may have been preassembled. If a part is not in the hardware kit, check to see if it has been pre-
assembled. If a part is missing, call 1-866-699-3756.
M10 Locknut
(63)–4
M8 Locknut
(60)–4
M8 Split
Washer (59)–5
M6 Washer
(55)–8
M8 x 25mm Button
Screw (33)–3
M8 x 70mm Button
Bolt (54)–2
M6 Locknut
(72)–4
M10 x 75mm Carriage Bolt (51)–4
M6 x 42mm Button
Screw (49)–4
M6 x 38mm Patch
Screw (48)–4
M6 x 38mm Button
Bolt (69)–4
M4 x 16mm
Screw (52)–4

6
1.
While another person lifts the front of the Frame (1),
attach the Front Stabilizer (3) to the Frame with two
M10 x 75mm Carriage Bolts (51) and two M10
ocknuts (63).
3
51
1
1
3. Attach the Wheels (18) to the Rear Stabilizer (4)
with two M8 ocknuts (60). Press a Wheel Cap (19)
onto each Wheel.
Attach the Rear Stabilizer (4) to the Rear Frame (2)
with two M10 x 75mm Carriage Bolts (51) and two
M10 ocknuts (63).
2. Slide the Rear Frame (2) out of the Frame (1), and
then tighten the Adjustment Knob (17) into the
Frame.
51
18
4
18
19
3
63
63
60
2
To make assembly easier, read the information
on page 5 before you begin assembling the
exercise cycle.
63
17
2
1
2

7
5. Attach the Backrest (5) to the Seat Frame (7) with
four M6 x 38mm Patch Screws (48) and four M6
Washers (55). Do not tighten the Patch Screws
yet.
5
5
7
55
55
48
48
4. Attach the Seat Frame (7) to the Handlebar (6) with
two M8 x 70mm Button Bolts (54), two M8 Split
Washers (59), and two M8 ocknuts (60). Do not
tighten the Button Bolts yet.
7
6
60
54
59
59
4

8
7
Battery Cover
Batteries
16
7. The Console (16) can use four 1.5V “D” batteries
(not included); alkaline batteries are recommended.
IMPORTANT: If the Console has been exposed
to cold temperatures, allow it to warm to room
temperature before inserting batteries.
Otherwise, you may damage the console dis-
plays or other electronic components. Remove
the battery cover, insert the batteries into the bat-
tery compartment, and reattach the battery cover.
Make sure to orient the batteries as shown by
the diagram inside the battery compartment.
To purchase an optional AC adapter, contact the
store where you purchased this product or call
the telephone number on the cover of this man-
ual. To avoid damaging the console, use only a
manufacturer-supplied AC adapter. Plug one end
of the AC adapter into the jack on the console; plug
the other end into an outlet installed in accordance
with all local codes and ordinances.
12
55
55
55
7
6
49
2
49
6. Have another person hold the Seat Frame (7) under
the Rear Frame (2) as shown. Attach the Seat
Frame and the Seat (12) to the Rear Frame with
four M6 x 42mm Button Screws (49) and four M6
Washers (55).
See step 4. Tighten the two M8 x 70mm Button
Bolts (54).
See step 5. Tighten the four M6 x 38mm Patch
Screws (48).

9
9. While another person holds the Console (16) near
the Upright (13), connect the console wire to the
Upper Wire Harness (36). Then, connect the con-
sole pulse wires to the Pulse Wires (71). Insert the
excess wire downward into the Upright.
Tip: Do not pinch the wires. Attach the Console
(16) to the Upright (13) with four M4 x 16mm
Screws (52).
916
Console
Wire
Pulse Wires
52
13 Do not pinch
the wires during
this step
36
71
8. Identify the eft Pulse Bar (65), which is marked
with a “ eft” sticker.
Have another person hold the eft Pulse Bar (65)
near the left side of the Upright (13). Make sure
that the hexagonal holes are in the indicated
location.
Insert the left Pulse Wire (71) into the Upright (13)
and pull it upward out of the top of the Upright.
Tip: Do not pinch the wires. Slide the eft Pulse
Bar (65) onto the Upright (13). Attach the eft Pulse
Bar with two M6 x 38mm Button Bolts (69) and two
M6 ocknuts (72). Make sure that the ocknuts
are in the hexagonal holes.
Repeat this step for the Right Pulse Bar (66).
8
65
13
66
69
71
71
36
72
Do not pinch
the wires during
this step
Hexagonal
Holes

10
11
25
24
Tab
31
11. Identify the eft Pedal (24), which is marked with a
“ eft” sticker. Firmly tighten the eft Pedal counter-
clockwise into the left arm of the Crank (31).
Tighten the Right Pedal (not shown) clockwise into
the right arm of the Crank. IMPORTANT: Tighten
both pedals as firmly as possible. After using
the exercise cycle for one week, retighten the
pedals. For best performance, keep the pedals
tightened.
Adjust the eft Pedal Strap (25) to the desired posi-
tion, and press the end of the eft Pedal Strap onto
the tab on the eft Pedal (24). Adjust the Right
Pedal Strap (not shown) in the same way.
12. Make sure that all parts are properly tightened before you use the exercise cycle. Note: Some hardware
may be left over after assembly is completed. Place a mat beneath the exercise cycle to protect the floor.
13
36
10
10. While another person holds the Upright (13) near
the Frame (1), connect the Upper Wire Harness
(36) to the ower Wire Harness (8).
Tip: Do not pinch the Wire Harnesses (8, 36).
Slide the Upright (13) onto the Frame (1). Attach
the Upright with three M8 x 25mm Button Screws
(33) and three M8 Split Washers (59).
8
33
33
59
59
1Do not pinch the
Wire Harnesses (8, 36)
during this step