Weslo Pursuit 30 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Serial Number
Decal
USER'S MANUAL
Model No. WLEX60907.0
Serial No.
Write the serial number in the
space above for reference.
www.weslo.com
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com

2
TABLE OF CONTENTS
WARNINGDECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEEXERCISECYCLE .......................................................10
MAINTENANCEANDTROUBLESHOOTING ...................................................15
EXERCISEGUIDELINES ...................................................................16
PARTLIST ..............................................................................18
EXPLODEDDRAWING ....................................................................19
ORDERINGREPLACEMENTPARTS ..................................................BackCover
LIMITEDWARRANTY ..............................................................BackCover
WESLO is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. Use the exercise cycle only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise cycle are ade-
quately informed of all precautions.
4. The exercise cycle is intended for home use
only. Do not use the exercise cycle in a com-
mercial, rental, or institutional setting.
5. Keep the exercise cycle indoors, away from
moisture and dust. Place the exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is at least 2 ft. (0.6 m) of clearance
around your exercise cycle.
6. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
7. Keep children under age 12 and pets away
from the exercise cycle at all times.
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise cycle. Always wear
athletic shoes for foot protection.
9. The exercise cycle should not be used by
persons weighing more than 250 lbs.
(113 kg).
10. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. The exercise cycle does not have a free
wheel; the pedals will continue to move until
the flywheel stops.
12. Always keep your back straight while using
the exercise cycle; do not arch your back.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
14. When you stop exercising, allow the pedals
to slowly come to a stop.
IMPORTANT PRECAUTIONS

4
Thank you for selecting the new WESLO®PURSUIT
U30 exercise cycle. Cycling is an effective exercise for
increasing cardiovascular fitness, building endurance,
and toning the body. The PURSUIT U30 exercise
cycle provides a selection of features designed to
make your workouts at home more effective and
enjoyable.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Water Bottle Holder*
Seat
Seat nob
Pedal/Strap
Console
Thumb Pulse Sensor
BEFORE YOU BEGIN
*No water bottle is included

ASSEMBLY
To hire an authorized service technician to assemble the exercise cycle, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires an adjustable wrench , a Phillips
screwdriver , and pliers .
Use the drawings below to identify the small parts used for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following
the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if
it has been preassembled.
5
M10 x 60mm Button
Screw (33)–2
M8 x 20mm
Button Screw (34)–3
M8 Split
Washer (42)–3
M8 Washer
(47)–4
M8 x 55mm Button
Screw (30)–4
M4 x 25mm Self-tapping
Screw (41)–3
M8 Locknut
(10)–4
M4 x 15mm
Screw (27)–4
1. Orient the Rear Stabilizer (6) with the “Up” sticker
facing upward. Slide the Rear Stabilizer into the
Frame (1). Attach the Rear Stabilizer with four M8 x
55mm Button Screws (30).
6
30
1
1

6
3
3. Attach the Left and Right Upright Covers (14, 15)
around the Frame (1) with three M4 x 25mm Self-
tapping Screws (41) as shown.
14
15
41
41
1
4. Attach the Seat (12) to the Seat Post (5) with four
M8 Washers (47) and four M8 Locknuts (10). Note:
The Washers and the Locknuts may be pre-
attached to the underside of the Seat.
4
12
5
47
47
10
10
2. Orient the Front Stabilizer (2) with the large holes
facing the Frame (1). Attach the Front Stabilizer to
the Frame with two M10 x 60mm Button
Screws (33).
1
2
33 2
Large
Holes

7
6
34
46
42 34
52
13
1
42
6. While another person holds the Upright (13) near
the Frame (1) as shown, connect the Upper Wire
(52) to the Lower Wire (46). Then, insert the wires
downward into the Frame.
Tip: Avoid pinching the Wires (46, 52) during this
step. Insert the Upright (13) into the Frame (1).
Attach the Upright with three M8 x 20mm Button
Screws (34) and three M8 Split Washers (42).
Avoid pinching
the Wires (46, 52)
during this step
5. Turn the Seat nob (9) counterclockwise and
remove it from the Frame (1). Then, insert the Seat
Post (5) into the Frame. Adjust the Seat Post to the
desired height and insert the Seat nob through the
indicated hole in the Frame into one of the adjust-
ment holes in the Seat Post. Then, turn the Seat
nob clockwise until it is tight. Make sure that the
Seat Knob is firmly engaged into one of the
adjustment holes in the Seat Post.
5
5
1
9
Hole
Adjustment
Holes

8
8. While a second person holds the Console (16) near
the Upright (13), connect the console wire to the
Upper Wire (52). Then, insert the wires downward
into the Upright.
Tip: Avoid pinching the wires during this step.
Attach the Console (16) to the Upright (13) with four
M4 x 15mm Screws (27).
8
Avoid pinching
the wires during
this step
52
27
13
Console
Wire
16
7. The Console (16) requires four 1.5V “D” batteries
(not included); alkaline batteries are recommended.
IMPORTANT: If the exercise cycle has been
exposed to cold temperatures, allow it to warm
to room temperature before inserting batteries
into the Console. If you do not do this, the con-
sole displays or other electronic components
may become damaged. Press the tab on the bat-
tery cover and remove it. Insert four batteries into
the Console as shown. Make sure that the batter-
ies are oriented as shown by the diagram inside
the battery compartment. Then, reattach the bat-
tery cover.
7
16
Batteries
Battery
Cover

9
10. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly is
completed, some extra parts may be left over. Place a mat beneath the exercise cycle to protect the floor.
9. Identify the Left Pedal (24), which is marked with
an “L” sticker. Using an adjustable wrench, firmly
tighten the Left Pedal counterclockwise into the
left arm of the Crank (21). Next, tighten the Right
Pedal (not shown) clockwise into the right arm of
the Crank. IMPORTANT: Tighten both Pedals as
firmly as possible. After using the exercise
cycle for one week, retighten the Pedals. For
best performance, keep the Pedals tightened.
Press the ends of a Pedal Strap (53) onto the
tabs on the Left Pedal (24) as shown. Attach the
other Pedal Strap (not shown) in the same
way.
9
24
53 21

10
HOW TO USE THE EXERCISE CYCLE
HOW TO AD UST THE SEAT POST
For effective exercise, the seat should be at the prop-
er height. As you pedal, there should be a slight bend
in your knees when the pedals are in the lowest posi-
tion. To adjust the height of the seat, first turn the seat
knob counterclockwise and remove it. Next, slide the
seat post upward or downward and align one of the
adjustment holes in the seat post with the indicated
hole in the Frame. Insert the seat knob into the frame
and the seat post, and turn the seat knob clockwise
until it is tight. Make sure that the seat knob is
inserted through one of the adjustment holes in
the seat post.
Seat Post
Seat nob
Hole
Seat