Weslo WLEX70907.0 User manual

Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
Model No. WLEX70907.0
Serial No.
Write the serial number in the
space above for reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manu-
al for future reference.
USER’S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
DO NOT CONTACT THE STORE.
For assistance, contact our
Customer Service Department.
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.wesloservice.com

2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE EXERCISE CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WESLO is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
The warning decal shown here
has been applied in the location
shown. If the decal is missing
or illegible, call the telephone
number on the front cover of
this manual and request a free
replacement decal. Apply the
decal in the location shown.
Note: The decal may not be
shown at actual size.

3
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over the age of 35 or per-
sons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the exercise cycle are ade-
quately informed of all precautions.
3. Your exercise cycle is intended for home use
only. Do not use your exercise cycle in a
commercial, rental, or institutional setting.
4. Keep your exercise cycle indoors, away from
moisture and dust. Place your exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around your exer-
cise cycle to mount, dismount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your exercise cycle at all times.
7. Your exercise cycle should not be used by
persons weighing more than 250 lbs.
(113 kg).
8. Wear appropriate exercise clothes while
exercising; do not wear loose clothes that
could become caught on your exercise
cycle. Always wear athletic shoes for foot
protection while exercising.
9. When adjusting the seat, insert the seat pin
into one of the holes in the seat post. Do not
insert the seat pin under the seat post.
10. Keep your back straight while using your
exercise cycle; do not arch your back.
11. When you stop exercising, allow the pedals
to slowly come to a stop.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. Use your exercise cycle only as described in
this manual.
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS

4
BEFORE YOU BEGIN
Handlebars
Resistance Knob
Flywheel
Seat
Seat Post
Pedal Side Shield
Seat Pin
Console
Thank you for selecting the new WESLO PURSUIT®
E 28 exercise cycle. The PURSUIT E 28 exercise
cycle blends advanced engineering with contemporary
styling to provide you with effective, low-impact work-
outs in the convenience and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
To avoid a registration fee for any service needed
under warranty, you must register the exercise
cycle at www.wesloservice.com/registration.
Before reading further, please look at the drawing
below and familiarize yourself with the labeled parts.
Adjustable Endcap

5
2
5
14
1
9
18
Square
Holes
2
Slot
1
32
2. Turn the Front Stabilizer (5) so that the square holes
face away from the saddle bracket on the front of
the Frame (1). Attach the Front Stabilizer with two
M8 x 40mm Carriage Bolts (18), two M8 Curved
Washers (14), and two M8 Nylon Locknuts (9).
1. See the inset drawing. Remove the Shipping Insert
(54) from the Frame (1) and discard it.
Turn the Rear Stabilizer (2) so that the slot faces
downward, and insert the Rear Stabilizer into the
Frame (1). Attach the Rear Stabilizer with four M5 x
10mm Machine Screws (32).
ASSEMBLY
To hire an authorized service technician to assemble the exercise cycle, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included
hex tools, assembly requires your own Phillips screwdriver and adjustable
wrench . A small amount of liquid soap is also required.
11
54

6
3. Remove all parts from the Pivot Axle (3). Insert the
Pivot Axle into the Frame (1). Align the hole in the
center of the Pivot Axle with the hole in the center of
the Frame. Tighten an M5 x 10mm Machine
Screw (32) into the Frame and the Pivot Axle.
Slide the Left and Right Handlebars (40, 41) onto
the ends of the Pivot Axle (3). Slide an M8 Flat
Washer (38) onto each end of the Pivot Axle, and
then thread an M8 Nylon Locknut (9) onto each end
of the Pivot Axle. Tighten each Nylon Locknut until
at least two threads on the end of the Pivot Axle
extend past the Nylon Locknut. Make sure that the
Handlebars move freely.
Press a Pivot Endcap (50) onto each end of the
Pivot Axle (3).
Apply a small amount of liquid soap to the upper
end of each Handlebar (40, 41). Slide a Foam Grip
(42) onto each Handlebar. Make sure that there is
a Handlebar Endcap (55) in each Handlebar.
3
40
1
32 Hole
38 9
41
55
55
42
42
3
50
50
9
4
Battery Door
Battery
7
28
Console
Plate
4. The Console (7) requires one “AAA” battery (not
included); an alkaline battery is recommended.
IMPORTANT: If the exercise cycle has been
exposed to cold temperatures, allow it to warm
to room temperature before inserting batteries
into the Console. If you do not do this, the con-
sole displays or other electronic components
may become damaged. See the inset drawing.
Remove the battery door from the back of the
Console and insert the battery into the Console.
Make sure that the battery is oriented as shown
by the diagram inside the battery compartment.
Then, reattach the battery door.
Next, plug the Reed Switch Wire (28) fully into the
socket on the back of the Console (7).
Slide the Console (7) onto the console plate. Note:
The Console is held by friction; it does not snap into
place.
38

7
5. Attach the Seat (11) to the Seat Post (10) with four
M8 Nylon Locknuts (9) and four M8 Spring Washers
(8). Note: The Nylon Locknuts and Spring Washers
may be pre-attached to the Seat.
Press the Frame Bushing (4) into the Frame (1).
(Note: The Frame Bushing may be pre-assembled.)
Next, insert the Seat Post (10) into the Frame.
Align one of the holes in the Seat Post (10) with the
hole in the Frame (1). Insert the Seat Pin (31) into
the Frame and the Seat Post. Make sure that the
Seat Pin is inserted into one of the holes in the
Seat Post; do not insert the Seat Pin under the
Seat Post. Tighten the Seat Pin into the Frame.
8
11
1
Hole
8
31
9
9
10
22 49
6
20
44
46
47
6. Identify the Right Pedal (22), which is marked with
an “R” sticker. Remove only the Right Pedal Nut
(47) and the Pedal Bushing (46) from the Right
Pedal. Next, insert the shaft of the Right Pedal into
the right Pedal Arm (49). Slide the Pedal Bushing
onto the Right Pedal, and position the Pedal
Bushing so that it slides into the Pedal Arm. Tighten
the shaft of the Right Pedal
clockwise into the right
arm of the Crank (20) as firmly as possible. Then,
tighten the Pedal Nut clockwise onto the Right
Pedal. Make sure that the Right Pedal and the
Pedal Nut are tightened as firmly as possible.
Repeat this step to attach the Left Pedal (not
shown), turning the Left Pedal and the Left Pedal
Nut (not shown)
counterclockwise .
7. Make sure that all parts are properly tightened before you use the exercise cycle. Note: Some hard-
ware may be left over after assembly is completed. Place a mat under the exercise cycle to protect the
floor or carpet from damage.
4
5

8
HOW TO ADJUST THE SEAT
For effective exer-
cise, the seat must
be at the proper
height. As you
pedal, there
should be a slight
bend in your knees
when the pedals
are in the lowest
position. To adjust
the seat, first hold
the seat and turn
the seat pin coun-
terclockwise to remove it. Next, align a different hole
in the seat post with the hole in the frame, and insert
the seat pin into the frame and the seat post. Make
sure to insert the seat pin into the seat post; do
not insert the seat pin under the seat post. Tighten
the seat pin into the frame.
HOW TO ADJUST THE PEDALING RESISTANCE
To vary the intensi-
ty of your exercise,
you can adjust the
pedaling resis-
tance. To increase
the resistance,
turn the resistance
knob clockwise; to
decrease the resis-
tance, turn the
knob counterclock-
wise.
LEVELING THE EXERCISE CYCLE
The exercise cycle
features adjustable
endcaps on the
front stabilizer. If
the exercise cycle
rocks on your floor,
turn one or both of
the endcaps until
the rocking motion
is eliminated.
BATTERY INSTALLATION
Before the console can be operated, one “AAA” bat-
tery must be installed. If you have not installed a bat-
tery, see assembly step 4 on page 6.
DESCRIPTION OF THE CONSOLE
The console features five modes that provide instant
exercise feedback during your workouts. The modes
are described below.
• Scan mode—Displays the speed, time, distance, and
calories modes, for five seconds each, in a repeating
cycle.
• Time mode—Displays the elapsed time. Note: If you
stop pedaling for five seconds or longer, the time
mode will pause and a stop symbol will appear in the
upper right-hand corner of the display.
• Speed mode—Displays your pedaling speed, in
miles per hour.
• Distance mode—Displays the total distance you
have pedaled, in miles.
• Calories mode—Displays the approximate number of
calories you have burned.
Note: The console also features a speed display. As
you increase your pedaling speed, additional indica-
tors will appear in the bar.
HOW TO USE THE EXERCISE CYCLE
Seat
Post
Seat
Pin
Resistance
Knob
Speed Display
Display
Mode
Indicators
Endcap
Stabilizer
Seat
Frame

9
HOW TO OPERATE THE CONSOLE
Note: If there is a sheet of clear plastic on the face of
the console, remove it before operating the console.
1. To turn on the power, press the mode button or
simply begin pedaling. When the power is turned
on, the entire display will appear for two seconds.
The console will then be ready for operation.
2. Select one of the five modes:
Scan mode—
When the
power is turned
on, the scan
mode will auto-
matically be
selected. One
mode indicator
will show that
the scan mode
is selected, and a second mode indicator will show
which mode is currently displayed. Note: If a differ-
ent mode is selected, you can select the scan
mode again by repeatedly pressing the mode but-
ton.
Time, speed,
distance, or
calories
mode—To
select one of
these modes
for continuous
display, press
the mode but-
ton repeatedly. The mode indicators will show
which mode is selected. Make sure that the scan
mode is not selected.
3. To reset the display, hold down the mode button
for two seconds. After the display is reset, the
scan mode will be selected.
4. To turn off the power, simply wait for about four
minutes. Note: The console has an “auto-off”
feature. If the pedals do not move and the
mode button is not pressed for a few minutes,
the power will turn off automatically to con-
serve the battery.
Mode Indicators

10
Inspect and tighten all parts of the exercise cycle reg-
ularly. Replace any worn parts immediately.
The exercise cycle can be cleaned with a soft, damp
cloth. Avoid spilling liquid on the console. Keep the
console out of direct sunlight or the display may be
damaged. Remove the battery when storing the exer-
cise cycle.
BATTERY REPLACEMENT
If the console does not function properly, the battery
should be replaced. See assembly step 4 on page 6.
In addition, make sure that the reed switch wire is
plugged fully into the console.
HOW TO TIGHTEN THE CRANK
If the arms of
the crank
become
loose, they
should be
tightened in
order to pre-
vent exces-
sive wear.
Loosen the
crank nut on
the left arm of
the crank.
Place the end of a standard screwdriver in one of the
slots in the slotted crank nut. Lightly tap the screwdriv-
er with a hammer to turn the slotted crank nut counter-
clockwise until the arms are no longer loose. Do not
overtighten the slotted crank nut. When the slotted
crank nut is properly tightened, retighten the crank
nut.
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedaling resistance when the
resistance knob is turned to the highest setting, the
resistance strap may need to be adjusted. To adjust
the resistance
strap, first turn
the resistance
knob counter-
clockwise to
the lowest set-
ting. Next,
locate the slot-
ted tab on the
front of the
exercise cycle.
Grip the
longest part the resistance strap underneath the slot-
ted tab and pull it towards the slot. When a little slack
is created, pull the end of the resistance strap tight.
Turn the crank for a moment to make sure that there
is not too much resistance.
HOW TO ADJUST THE CHAIN
The exercise cycle features a chain that must be kept
properly adjusted. If the chain causes excessive noise
or slips as you pedal, the chain should be adjusted.
To tighten the
chain, loosen,
but do not
remove, the
axle nuts on
both sides of
the flywheel.
Pull the fly-
wheel forward
slightly. Make
sure that the
flywheel is
straight and retighten the axle nuts.
MAINTENANCE AND TROUBLESHOOTING
Crank
Nut
Slotted
Crank
Nut
Crank Arm
Axle
Nut
Slotted
Tab
Resistance
Strap