Weslo CardioStride 2.0 User manual

Model No. 831.24902.0
Serial No.
Write the serial number in the
space above for future reference.
Serial
Number
Decal
• Assembly
•Operation
• Maintenance
• Part List and Drawing
Sears, Roebuck and Co.
Hoffman Estates, IL 60179
T A ILL
User's
ISE
Manual

TABLE OF CONTENTS
WARNING DECAL PLACEMENT .............................................................. 2
IMPORTANT PRECAUTIONS ................................................................. 3
BEFORE YOU BEGIN ....................................................................... 5
ASSEMBLY ............................................................................... 6
TREADMILL OPERATION .................................................................... 9
HOW TO FOLD THE TREADMILL ............................................................. 11
TROUBLESHOOTING ...................................................................... 12
EXERCISE GUIDELINES ................................................................... 13
PART LIST ............................................................................... 14
EXPLODED DRAWING ..................................................................... 15
ORDERING REPLACEMENT PARTS .................................................. Back Cover
90 DAY FULL WARRANTY ........................................................... Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, call
1-866-699-3756 and request a free replacement decal. Apply the decal in the location shown.
Note: The decal(s) may not be shown at actual size.
Toreduceriskofseriousinjury, standon Parareducirelriesgodelesionesserias, "
foot rails before starting treadmill; read en los fieles de soporte para los pies antes de
and understand the user's manual, all comenzar la maquina para correr, lea y
instructions, and all warnings before entienda el manual del usuario, todas las
use Keep children away instrucdones, y las advertendas antes del use.
(One on each side)

iMPORTANT PRECAUTIONS
WARNING: Toreducetheriskofseriousnjury,reada.importantprecautionsand
instructions in this manual and all warnings on your treadmill before using your treadmill. Sears
assumes no responsibility for personal injury or property damage sustained by or through the use
of this product.
,
.
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over age 35 or
persons with pre-existing health problems.
it is the responsibility of the owner to ensure
that all users of the treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
11.
treadmill. Athletic support clothes are recom-
mended for both men and women. Always
wear athletic shoes; never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
Do not operate the treadmiJl if the treadmill is
not working properly. (See TROUBLESHOOT-
iNG on page 12 if the treadmill is not working
properly.)
.
.
,
.
,
.
10.
Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
Place the treadmill on alevel surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
Do not operate the treadmilJ where aerosol
products are used or where oxygen is being
administered.
Keep children under age 12 and pets away
from the treadmill at alJ times.
The treadmill should not be used by persons
weighing more than 250 Ibs. (113 kg).
Never allow more than one person on the
treadmill at a time.
Wear appropriate exercise clothes while
using the treadmill. Do not wear loose
clothes that could become caught in the
12.
13.
14.
15.
16.
17.
18.
Always hold the handrails while using the
treadmiJl.
Do not attempt to raise or lower the treadmill
unti! it is properly assembled. (See ASSEM-
BLY on page 6 and HOW TO FOLD THE
TREADMILL on page 11.) You must be able to
safely lift 25 Ibs. (11 kg) to raise or Jower the
treadmill.
When folding the treadmill, make sure that
the storage latch is holding the frame secure-
ly in the storage position.
Do not change the incline of the treadmill by
placing objects under the treadmill.
Inspect and properly tighten all parts of the
treadmill regularly.
Never drop or insert any object into any
opening on the treadmill
Servicing other than the procedures in this
manual should be performed by an autho-
rized service representative only.

19. Over exercising may result in serious injury
or death, if you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
20. Do not place hands or feet under the tread-
mill while it is in use.
SAVE THESE
21. This treadmill is intended for home use only.
Do not use the treadmill in any commercial,
rental, or institutional setting.
22. The roller guards must be 1/8 in. (3 ram) from
the rear roller (see the drawing on page 5).
Adjust the roller guards, if necessary.
iNSTRUCTiONS

BEFORE YOU BEGIN
Thank you for selecting the new WESLO ®CARDIO
STRIDE 2.0 treadmill. The CARDIO STRIDE 2.0
treadmill offers a selection of features designed to
make your workouts at home more effective. And
when you're not exercising, the unique treadmill can
be folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the back cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Length: 4 ft. 5 in. (135 cm)
Width: 2 ft. 3 in. (69 cm)
Console
Handrail
Storage Pin
Walking Belt
Hood
Adjustment Pin
Roller
Rear
Roller Adjustment Screws
5

ASSEMBLY
Assembly requires only the included he_ and wrench _. To avoid damaging parts, do not
use power tools for assembly. Assembly requires two persons. Set the treadmill in a cleared area and
remove all packing materials. Do not dispose of the packing materials until assembly is completed. In the
drawing below, the numbers in parentheses are the key numbers of the parts, from the PART LIST near the end
of this manual. The numbers after the parentheses are the quantities needed for assembly. Note: Some small
parts may be pre-assembled. Extra hardware may be included. If a part is missing, call 1-866-699-3756.
M8 Nylon
Nut (13)-4 M8 Curved M8 Washer
Washer (37)-4 (34)-4
M4 x 12mm
Screw (3)-2 M5 x 10mm M8 x 15mm
Screw (10)-2 Screw (33)-4 M8 x 50mm Bolt (38)-4
,Identify the Right Upright (36), which has a single hole
in the indicated location. Orient the Right Upright so that
the two indicated holes are on the side shown, and hold
the Right Upright against the Base (14).
Attach the Right Upright (36) to the Base (14) with two
M8 x 50mm Bolts (38), two M8 Curved Washers (37),
and two M8 Nylon Nuts (13). Do not tighten the Nylon
Nuts yet.
Orient the Left Upright (35) so that the two indicated
holes are on the side shown, and attach the Left Upright
to the Base (14) in the same way. Do not tighten the
Nylon Nuts yet.
14
37
36
38_
Holes
37
2. Raise the Left Upright (35) and the Right Upright (36) to
the position shown. 2

AttachtheHood(28)tothefrontoftheFrame(29)with
twoM5x 10mmScrews(10). 28
10
.See drawing 4a. Hold the front of the Frame (29)
between the Left Upright (35) and the Right Upright
(36). Align the holes near the front of the Frame with
one of the two sets of adjustment holes in the Uprights.
Insert the two Adjustment Pins (4) into the holes in the
Uprights and the Frame. Make sure that the
Adjustment Pins are fully inserted at the same
height.
Next, look under the Frame (29) near the Left Upright
(35). See drawing 4b. Locate the Reed Switch Clip (11)
attached to the underside of the Frame. Insert the Reed
Switch (6) into the Reed Switch Clip as shown. Next,
locate the Magnet (12) on the left Flywheel (9). Turn the
Flywheel until the Magnet is aligned with the Reed
Switch. Move the Reed Switch so that there is a 1/8"
(3 ram) gap between the Reed Switch and the
Magnet. Then, tighten the M5 x 12mm Screw (44).
4a
4
44
1/8 in.
View from below
.Hold the Handrail (5) near the Left and Right Uprights
(35, 36). Connect the Handrail Wire (2) to the Reed
Switch Wire (6). Insert the Wires down into the Left
Upright.
Attach the Handrail (5) to the Uprights (35, 36) with four
M8 x 15mm Screws (33) and four M8 Washers (34). Be
careful not to pinch the Wires (2, 6). Do not fully
tighten the Screws yet.
Place the treadmill in the storage position (see page
11). Center the Frame (not shown) between the
Uprights (35, 36).
See step 1. Tighten the four M8 Nylon Nuts (13).
Then, tighten the M8 × 15ram Screws (33). Lower the
Frame (see page 11).
I34
7

.The Console (1) requires two "AAA" batteries; alkaline
batteries are recommended, Press the indicated tab on
the Battery Cover (27), and remove the Battery Cover.
Insert two batteries into the two battery clips; make
sure that the negative (-) ends of the batteries are
touching the springs in the battery clips. attere
.See drawing 7a. Hold the Console (1) near the
Handrail (5), Connect the wire on the Console to the
Handrail Wire (2), Then, attach the Console to the
Handrail with two M4 x 12mm Screws (3). Make sure
that the wires are not pinched.
See drawing 7b. Press the Battery Cover (27) onto the
Console (1).
7a 7b
27
.Remove the paper backing from the Adhesive Clip (30).
Press the Adhesive Clip onto the left side of the Frame
(29) in the indicated location. Then, press the Hex Key
(20) into the Adhesive Clip.
Make sure that the walking belt is properly tightened
(see SYMPTOM 3 on page 12).
20 30
9. Make sure that all parts are properly tightened before you use the treadmill. To protect the floor or car-
pet, place a mat under the treadmill.
8

TREADMILL OPERATION
STEP-BY-STEP CONSOLE OPERATION
Before the console can be operated, batteries must be
installed (see assembly step 6 on page 8). If there is a
thin sheet of plastic on the console, remove the plastic.
_ J
The console features six modes:
Speed--This mode displays your speed, in miles
per hour.
Distance--This mode displays the number of miles
you have walked.
Time--This mode displays the elapsed time.
Odometer--This mode displays the distance that
the walking belt has moved since the batteries
were changed.
Calorie--This mode displays the approximate
number of calories you have burned.
Scan--This mode displays the Speed, Distance,
Time, Odometer, and Calorie modes.
Follow the steps below to operate the console.
1. Turn on the power.
To turn on the power, press the console button or
begin walking. Note: If batteries were just installed,
the power will already be on. The first time you
use the treadmill, lubricate the walking platform
(see page 10).
2. Track your progress with the six modes.
When the power is
turned on, the Scan
mode will be select-
ed and the SCAN
indicator will appear.
The console will dis-
play the Speed,
Distance, Time,
sI ,,__,'='°°°l
SCAN Indicator
Odometer, and Calorie modes, for about six sec-
onds each, in a repeating cycle.
To select only the Speed, Distance, Time,
Odometer, or Calorie mode, press the console but-
ton until only the SPEED, DIST, TIME, ODO, or
CAL indicator appears in the display. Make sure
that the SCAN indicator does not appear.
To reset all modes (except for the odometer
mode), press the console button for about three
seconds.
3. Turn off the power.
To turn off the power, simply wait for a few min-
utes. If the walking belt is not moved and the con-
sole button is not pressed for a few minutes, the
power will turn off automatically.
9

iNCLiNE ADJUSTMENT LUBRiCATiNG THE WALKING PLATFORM
The incline of the treadmill can be adjusted to two
positions. Hold the front of the Frame (29), and
remove the two Adjustment Pins (4). Raise or lower
the Frame, align the holes in the Frame with one of
the sets of holes in the Uprights (35, 36), and then
reinsert the Adjustment Pins.
Before the treadmill is used, the walking platform
should be lubricated. Open the included lubricant
packet. Reach under one side of the walking belt as
far as you can, and apply half of the lubricant to the
walking platform. Then, reach under the other side of
the walking belt and apply the remaining lubricant.
After you have applied the lubricant, walk on the
treadmill for a few minutes to spread the lubricant.
Apply
lubricant
here _..
pply
lubricant
here
10