Westermo Viper-008 User manual

Viper-008
Unmanaged 8-port Ethernet Switch
www.westermo.com

26641-2211

3
6641-2211
General Information
Legal Information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind are made in relation to the accuracy and reliability or contents
of this document, either expressed or implied, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income
or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at www.westermo.com

46641-2211
Safety and Regulations
Warning signs are provided to prevent personal injury and/or damages to the product.
The following levels are used:
Level of warning Description Consequence
personal injury
Consequence
material damage
WARNING
Indicates a potentially
hazardous situation
Possible death or
major injury
Major damage to the
product
CAUTION
Indicates a potentially
hazardous situation
Minor or moderate
injury
Moderate damage to
the product
NOTICE
Provides information
in order to avoid
misuse of the
product, confusion or
misunderstanding
No personal injury Minor damage to the
product
NOTE
Used for highlighting
general, but important
information
No personal injury Minor damage to the
product

5
6641-2211
Before Installation
Read this manual completely and gather all information on the product. Make sure that
you understand it fully. Check that your application does not exceed the safe operating
specifications for this product.
SAFETY DURING INSTALLATION
The product must be installed by qualified service personnel
and built in to an apparatus cabinet or similar, where access is
restricted to service personnel only.
Refer to Compliance Information to see the required level of
qualified service personnel according to safety standards.
During installation, ensure a protective earthing conductor is
first connected to the protective earthing terminal (only valid for
metallic housings). Westermo recommends a cross-sectional area
of at least 4 mm2.
Upon removal of the product, ensure that the protective earthing
conductor is disconnected last.
HAZARDOUS VOLTAGE
Do not open an energized product. Hazardous voltage may occur
when connected to a power supply.
PROTECTIVE FUSE
The power supply wiring must be sufficiently fused. The fuse must
be IEC 60127 certified and rated for T1.25 A and 250 V.
It must be possible to disconnect manually from the power supply.
Ensure compliance to national installation regulations.
This product has no internal fuse and should be connected via an
external fuse for protection.

66641-2211
HOT SURFACE
Be aware that the surface of this product may become hot.
When it is operated at high temperatures, the external surface
may exceed Touch Temperature Limit according to the product's
relevant electrical safety standard.
ELECTROSTATIC DISCHARGE (ESD)
Prevent electrostatic discharge damages to internal electronic
parts by discharging your body to a grounding point (e.g. use a
wrist strap).
REDUCE THE RISK OF FIRE
To reduce the risk of fire, use only telecommunication line cords
with a cable diameter of AWG 26 or larger. Regarding power
cable dimensions, see Interface Specifications.

7
6641-2211
Care Recommendations
Follow the care recommendations below to maintain full operation of product and to
fulfill the warranty obligations:
• Do not drop, knock or shake the product. Rough handling above the specification
may cause damage to internal circuit boards.
• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh
chemicals, cleaning solvents or strong detergents.
• Do not paint the product. Paint can clog the product and prevent proper operation.
If the product is used in a manner not according to specification, the protection provided
by the equipment may be impaired.
If the product is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo technical support.
Product Disposal
This symbol means that the product shall not be treated
as unsorted municipal waste when disposing of it. It needs
to be handed over to an applicable collection point for
recycling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.

86641-2211
Agency Approvals and Standards Compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
EN 50121-3-2, Railway applications - EMC: Rolling stock - Apparatus
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
Environmental EN 50155 Railway applications - Electronic equipment used on rolling
stock
Fire protection EN 45545-2, Fire protection on railway vehicles
Safety EN/IEC/UL 62368-1, Safety Requirements for audio/video, information
and communication technology equipment
Compliance Information
EN/IEC/UL 62368-1 Notice
This product has been tested and found compliant to EN/IEC/UL 62368-1, Safety
for Communication Technology. In accordance with the definitions of the standard,
this product shall be handled by ordinary personnel. Energy source classifications are
according to following:
EN/IEC/UL 62368-1 notice
Electrical energy source Power port ES1 (at 24 VDC)
ES3 (at 110 VDC)
Serial port ES1
Ethernet port ES1, TNV-1
Power source Power port PS3
Thermal energy source Enclosure TS1
Mechanical energy
source
Enclosure MS1 (MS3 for wall or ceiling
mounting)
Radiation energy source N/A N/A

9
6641-2211
Declaration of Conformity
Hereby, Westermo declares that this product is in compliance with applicable EU
directives and UK legislations. The full declaration of conformity and other detailed
information is available at www.westermo.com/support/product-support.
FCC Part 15.105 Notice:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
… Reorient or relocate the receiving antenna
… Increase the separation between the equipment and receiver
… Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.

10 6641-2211
Type Tests and Environmental Conditions
Phenomena Test Description Test levels
ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit A)
Enclosure air ± 8 kV (crit A)
RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz),
80 - 2500 MHz (crit A)
10 V/m 80% AM (1 kHz),
2700 - 6000 MHz (crit A)
Fast transient EN 61000-4-4 Ethernet ports ± 2 kV (crit A)
Power port ± 2 kV (crit A)
Earth port ± 2 kV (crit A)
Surge EN 61000-4-5 Fault port ± 2 kV line to earth (crit A)
Ethernet ports ± 2 kV line to earth (crit A)
Power port ± 2 kV line to earth, ± 2 kV line to line
(crit A)
RF conducted EN 61000-4-6 Ethernet ports 10 V 80% AM (1 kHz), 0.15 - 80 MHz
(crit A)
Power port 10 V 80% AM (1 kHz), 0.15 - 80 MHz
(crit A)
Power frequency magnetic
field
EN 61000-4-8 Enclosure 1000 A/m 50 Hz
300 A/m 16.7 Hz, 60 Hz, DC (crit A)
Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m (crit A)
Voltage dips and interruption EN 50155 DC power ports 10 ms interruption, 100 ms ±40% voltage
variation
Radiated emission CISPR 16-2-3
ANSI C63.4
(FCC part 15)
Enclosure Class B (30 - 6000 MHz)
Conducted emission CISPR 16-2-1 DC power port &
Ethernet ports
Class B
Dielectric strength EN 50155 Ethernet ports to other
isolated ports
500 VAC 1 min
Power & Fault port to
other isolated ports
1500 VAC 1 min
Temperature EN 60068-2-1
EN 60068-2-2
Operating -40 to +70ºC
Storage & Transport -40 to +85ºC
Humidity EN 60068-2-30 Operating 5 to 95% relative humidity
Storage & Transport 5 to 95% relative humidity
Altitude Operating 2000 m / 70 kPa
Reliability prediction (MTBF) MIL-C217F2, GB Operating 150 years @ 20 ºC
147 years @ 40 ºC
135 years @ 60 ºC
Service life Operating 10 years
Vibration, random simulated
long life
IEC 60068-2-64,
Cat. 1 class B
(EN 61373)
Not Operating Vertical: 7.9 m/s2
Transverse: 7.9 m/s2
Longitudinal: 7.9 m/s2
3 x 5 h
Vibration, random functional IEC 60068-2-64,
Cat. 1 class B
(EN 61373)
Operating Vertical: 1.0 m/s2
Transverse: 1.0 m/s2
Longitudinal: 1.0 m/s2
3 x 10 min
Shock, half sine pulses IEC 60068-2-27,
Cat. 1 class B
(EN 61373)
Operating Vertical: 50 m/s2
Transverse: 50 m/s2
Longitudinal: 50 m/s2
30 ms, 3 x 6 shocks

11
6641-2211
Phenomena Test Description Test levels
Shock, sawtooth IEC 60068-2-27,
Cat. 1 class B
(IEEE1478-2001)
Operating Vertical: 100 m/s2
Transverse: 100 m/s2
Longitudinal: 100 m/s2
11 ms, 3 x 6 shocks
Enclosure UL 94 Nickel coated zinc Flammability class V-1
Dimension W x H x D 175 x 100 x 53,4 mm
Weight 0.9 kg
Degree of protection IEC 529 Enclosure IP 65 when all ports are protected/
connected else IP 40
Cooling Convection
Mounting DIN Rail or wall mounted

12 6641-2211
Description
Viper-008 is a unmanaged switch developed for rail and industrial applications. To meet
the environmental requirements from rail and harsh industrial applications the switch
has rugged M12 Ethernet connectors and full metal housing. The IP65 sealed metal case
make it robust and allows for the surrounding air temperature to be between -40 to
+70°C. There are no sensitive or fragile components, hardening the product against
shock and vibration making these units suitable for rolling stock usage. The power supply
operates over a wide input range from 24 to 110 VDC.
Interface Specifications
Power and fault relay port PWR
Rated voltage 24 to 110 VDC
Operating voltage 16.8 to 143 VDC (14.4 to 154 VDC for 100 ms)
Rated current 110 mA @ 24 VDC
33 mA @ 110 VDC
Rated frequency DC
Inrush current, I2tMax 0.02 A2s @ 24 - 110 VDC
Polarity Reverse polarity protected
Startup current* 300 mA @ 16.8 VDC
Redundant power input No
Isolation to Connections X1 - X8 and to ground, 1500 VAC.
Fault relay belongs to the same isolation group as the power
supply lines (fault relay signals are also contained within
PWR).
Connection 4 pin male M12 connector with A-code
Connector size M12, recommended cable area 0.5 mm2recommended
(minimum 0.25 mm2), cable dimensions depend on choice of
M12 connector
Shielded cable Not required, twisted pair is recommended
Fault relay resistance < 10 Ω
* If external power supply is used it must meet specified startup current.
M12 A-Coded
Power
Connector
Position Direction Description
1 U+ Positive supply voltage
2 Out Alarm relay (status) +
30 V Negative supply voltage
4 Out Alarm relay (status) -
Housing Shield Chassis of product (ground)

13
6641-2211
Fault Contact
The Viper switch is equipped with a potential free normally closed fault contact. The
fault contact is a solid state component (relay) that requires power to work and it is
transient protected. Additionally, the fault contact is opened when any of the following
conditions is met:
• No voltage on the power supply pin, a voltage level outside the legal voltage range
or current limitation on the voltage source is applied on the power input.
Description of how connection to the fault contact could be done is shown below. The
relay is closed when the unit is OK and open at failure. The relay is of semiconductor
type (no moving parts). It is specified for max current 250 mA continuous, 500 mA
peak (10 ms), operational voltage up to 110 V, protected by a 150 VDC-varistor,
ON-resistance less than 10 Ohm, and leakage current max 1 µA.
External relay
+24/48 VDC +
1 kΩ
0V
Viper
2 2
4 4
Viper
To logic input
Input on PLC
Service Port
The service port should not be used by non other than the Westermo Technical Support
team. Do not connect any device or cable to the Service Port.

14 6641-2211
Ethernet TX port X1 to X8
Electrical specification IEEE std 802.3. 2005 Edition
Data rate 10 Mbit/s or 100 Mbit/s
Duplex Full or half
Circuit type TNV-1
Transmission range 100 m
Isolation to Other Ethernet ports, 500 VAC
PWR, 1500 VAC
Galvanic connection to None, except for shielded contact to housing
Connection 4-pole M12 female with D-code
Shielded cable Not required, twisted pair is recommended
Conductive housing Nickel plated zinc, metal housings of X1-X8 also connected
to the housing
Number of ports 8 Ethernet (X1-X8)
Position Direction Description
1 Out Transmit Data +
2 In Receive Data +
3 Out Transmit Data -
4 In Receive Data -
Housing Shield Chassis of product (ground)

15
6641-2211
Location of Interface Ports, LEDs
LED indicators
LED Status Description
PWR GREEN Unit indicates no fault
RED Unit indicated fault
X1 to X8 OFF No Link
GREEN Link is up
GREEN
FLASH
Data is transmitted
X1
X2 X6
X3 X7
PWR
SERVICE
X4 X8
X5

16 6641-2211
Mounting, DIN-rail
This unit can be mounted on 35 mm DIN-rail, which is horizontally mounted inside an
apparatus cabinet or similar. Snap on mounting, see figure.
Removal
Press down the support at the back of the unit using a screwdriver. See figure.

17
6641-2211
Removal
Disconnect all cables and unscrew the unit from the wall.
Cooling
This unit uses convection cooling. Avoid obstructing the airflow around the unit. Spacing
is recommended for the use of unit in full operating temperature range and service life.
Wall Mounting
There are four 6 mm bore holes intended for mounting the unit. The unit can be
mounted vertical or horizontal. Use four M6 screws with 12 mm washer on a flat and
stable surface.
X1
X2 X6
X3 X7
PWR
SERVICE
X4 X8
X5

18 6641-2211
Dimensions
Measurements are stated in millimeters.

19
6641-2211

REV. I 6641-2211 2022-08 Westermo Network Technologies AB, Sweden
Westermo • Metallverksgatan 6, SE-721 30 Västerås, Sweden
Tel [phone] Fax [phone]
E-mail: [e-mail]
www.westermo.com