Westermo Ibex-RT-610 Series User manual

w w w. w ester m o .com
Ibex-RT-610 Series
EN 50155 WLAN 802.11ac Dual Concurrent Access Point

Table of Contents
1. General Information ........................................................................ 3
1.1. Legal Information ................................................................... 3
1.2. About This Guide ................................................................... 3
1.3. Software Tools ...................................................................... 3
1.4. License and Copyright for Included FLOSS ................................. 3
2. Safety and Regulations ................................................................... 4
2.1. Warning Levels ..................................................................... 4
2.2. Safety Information ................................................................. 5
2.3. Care Recommendations ......................................................... 6
2.4. Product Disposal ................................................................... 7
2.5. Compliance Information .......................................................... 7
2.5.1. Agency Approvals and Standards Compliance .................... 8
2.5.2. United States - FCC ...................................................... 8
2.5.3. United States - AREMA .................................................. 9
2.5.4. Canada - IC ................................................................. 9
2.5.5. Simplified Declaration of Conformity ................................ 10
3. Product Description ...................................................................... 11
3.1. Product Description .............................................................. 11
3.2. Available models ................................................................. 12
3.3. Hardware Overview ............................................................. 12
3.3.1. Frontside Overview ..................................................... 12
3.3.2. Front Side Label ......................................................... 12
3.3.3. Rear Side Label .......................................................... 13
3.3.4. Interface Ports View ..................................................... 13
3.4. Connector Information .......................................................... 14
3.4.1. Power Input Connection ............................................... 14
3.4.2. Ethernet Ports ............................................................ 14
3.4.3. Antenna Ports ............................................................ 15
3.5. LED Indicators .................................................................... 16
3.6. Dimensions ........................................................................ 16
4. Installation .................................................................................. 18
4.1. Mounting ........................................................................... 18
4.2. Factory Reset ..................................................................... 18
4.3. Earth connection ................................................................. 19
4.4. Connection of Cables ........................................................... 19
4.5. Cooling .............................................................................. 20
4.6. Replacement of Product ........................................................ 21
5. Specifications .............................................................................. 22
5.1. Interface Specifications ......................................................... 22
5.2. Type Tests and Environmental Conditions ................................. 25
6. Abbreviations and Terms ............................................................... 27
7. Revision Notes ............................................................................ 29
2 Ibex-RT-610 Series

1. General Information
1.1. Legal Information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind are made in relation to the accuracy and reliability or contents of
this document, either expressed or implied, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. Westermo reserves the
right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at www.westermo.com.
1.2. About This Guide
This guide is intended for installation engineers and users of the Westermo products.
It includes information on safety and regulations, a product description, installation
instructions and technical specifications.
1.3. Software Tools
Related software tools are available at www.westermo.com/support/software-tools.
1.4. License and Copyright for Included FLOSS
This product includes software developed by third parties, including Free/Libre Open
Source Software (FLOSS). The specific license terms and copyright associated with the
software are included in each software package respectively. Please visit the product web
page for more information.
Upon request, the applicable source code will be provided. A nominal fee may be charged
to cover shipping and media. Please direct any source code request to your normal sales or
support channel.
Ibex-RT-610 Series 3

2. Safety and Regulations
2.1. Warning Levels
Warning signs are provided to prevent personal injuries and/or damages to the product.
The following levels are used:
Level of warning Description Consequence
personal injury
Consequence
material damage
WARNING
Indicates a potentially
hazardous situation
Possible death or major
injury
Major damage to the
product
CAUTION
Indicates a potentially
hazardous situation
Minor or moderate
injury
Moderate damage to the
product
NOTICE
Provides information in order
to avoid misuse of the
product, confusion or
misunderstanding
No personal injury Minor damage to the
product
NOTE
Used for highlighting general,
but important information
No personal injury Minor damage to the
product
Table 1. Warning levels
4 Ibex-RT-610 Series

2.2. Safety Information
Before installation:
Read this manual completely and gather all information available on the product. Make sure
it is fully understood. Check that your application does not exceed the safe operating
specifications for the product.
WARNING - SAFETY DURING INSTALLATION
The product must be installed and operated by qualified service personnel
and installed into an apparatus cabinet or similar, where access is
restricted to service personnel only. For Ibex products, outdoor
installation is allowed.
During installation, ensure a protective earthing conductor is first
connected to the protective earthing terminal (only valid for metallic
housings). Westermo recommends a cross-sectional area of at least 4
mm2.
Upon removal of the product, ensure that the protective earthing
conductor is disconnected last.
WARNING - HAZARDOUS VOLTAGE
Do not open an energised product. Hazardous voltage may occur when
connected to a power supply.
WARNING - PROTECTIVE FUSE
The power supply wiring must be sufficiently fused.
It must be possible to disconnect manually from the power supply. Ensure
compliance to national installation regulations.
WARNING - POWER SUPPLY CONNECTION
There are safety regulations governing the power source that can be used
in conjunction with the product. Refer to Interface Specifications.
Ibex-RT-610 Series 5

WARNING - RADIO PRODUCTS
Observe the usage limitations of radio products at filling stations, in
chemical plants, in systems with explosives or potentially explosive
locations.
The product may not be used in airplanes. Exercise particular caution near
personal medical aids, such as pacemakers and hearing aids. Never
perform work on the antenna system during a thunderstorm.
To fulfill human safety, a minimum separation distance of 20 cm or more
should be maintained between the antenna of the product and personnel
during operation.
CAUTION - HOT SURFACE
Be aware that the surface of this product may become hot. When it is
operated at high temperatures, the external surface may exceed Touch
Temperature Limit according to the product's relevant electrical safety
standard.
This product complies with Touch Temperature Limits throughout its
operational temperature range.
CAUTION - CORROSIVE GASES
If the product is placed in a corrosive environment, it is important that all
unused connector sockets are protected with a suitable plug, in order to
avoid corrosion attacks on the gold plated connector pins.
CAUTION - CABLE TEMPERATURE RATING FOR FIELD
TERMINAL WIRES
There may be a requirement on the minimum temperature rating of the
cable to be connected to the field wiring terminals, see Interface
Specifications.
2.3. Care Recommendations
Follow the care recommendations below to maintain full operation of the product and to
fulfill the warranty obligations:
6 Ibex-RT-610 Series

• Do not drop, knock or shake the product. Rough handling above the specification may
cause damage to internal circuit boards.
• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh
chemicals, cleaning solvents or strong detergents.
• Do not paint the product. Paint can clog the product and prevent proper operation.
If the product is used in a manner not according to specification, the protection provided
by the equipment may be impaired.
If the product is not working properly, contact the place of purchase, the nearest
Westermo distributor office or Westermo technical support.
NOTE
Devices not used shall be kept in the factory sealed moisture barrier bag.
Open, unsealed devices should not be kept unpowered for more than 30
days.
2.4. Product Disposal
This symbol means that the product shall not be treated as unsorted municipal waste when
disposing of it. It needs to be handed over to an applicable collection point for recycling
electrical and electronic equipment.
By ensuring the product is disposed of correctly, you will help to reduce hazardous
substances and prevent potential negative consequences to both the environment and
human health, which could be caused by inappropriate disposal.
Figure 1. WEEE symbol for treatment of product disposal
2.5. Compliance Information
REGULATORY NOTICE
Any changes or modifications shall be approved by the party responsible
for compliance. If not, users could void the user's authority to operate the
equipment. Country code and antenna gain need to be set properly for
correct functionality in the installed country.
Ibex-RT-610 Series 7

2.5.1. Agency Approvals and Standards Compliance
Approvals and Standards
Climate • EN 50155, class OT4 Railway applications - Electronic equipment used on
rolling stock
• EN 50125-3, Railway applications – Environmental conditions for equipment,
Part 3: Equipment for signalling and telecommunications
EMC • EN 50155, Railway applications - Electronic equipment used on rolling stock
• EBA EMV 06, German Federal Railway Authority, Radio compatibility of rail
vehicles (valid for LV models only)
• EN 50121-3-2, Railway applications – Electromagnetic compatibility, Part 3-2:
Rolling stock – Apparatus
• EN 50121-4, Railway applications - Electromagnetic compatibility. Part 4:
Emission and immunity of the signalling and telecommunications apparatus
• ETSI EN 301 489-1, Electromagnetic compatibility (EMC) and Radio
spectrum Matters (ERM) for radio equipment and services - Part 1: Common
technical requirements
• ETSI EN 301 489-17, Electromagnetic compatibility (EMC) and Radio
spectrum Matters (ERM) for radio equipment - Part 17: Specific conditions
for Broadband Data Transmission Systems
• ECE E-Mark, Road Vehicles, E13 10R-06 15771 (valid for LV models only)
Mechanical
(Shock and vibration)
• EN 61373, category 1, class A and B
• EN 50125-3, Outside the track
Insulation
(Coordination and test)
• EN 50124-1, Railway applications – Insulation coordination
• EN 50155, Railway applications - Electronic equipment used on rolling stock
Radio communication • ETSI EN 300 328, Wideband transmission systems; Data transmission
equipment operating in the 2,4 GHz ISM band and using wide band
modulation techniques
• ISM band and using wide band modulation techniques
• ETSI EN 301 893, 5 GHz RLAN
• IEEE 802.11, Wireless LAN Medium Access Control (MAC) and Physical
Layer (PHY) Specifications
• FCC-47-15, Radio frequency devices
Safety • EN/IEC 62368-1, Safety Requirements for audio/video, information and
communication technology equipment
• EN 45545-2, Fire protection on railway vehicles
• NFPA 130, Fire protection for fixed guideway transit and passenger rail
system
2.5.2. United States - FCC
The enclosed product complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (i.) this product may not cause harmful interference and (ii.) this
product must accept any interference received, including interference that may cause
undesired operation.
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation
distance of 20 cm or more should be maintained between the antenna of this product and
8 Ibex-RT-610 Series

persons during operation. To ensure compliance, operations at closer distances than this
are not recommended.
This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This product
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this product does cause harmful interference to radio or television reception, which can
be determined by turning the product off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the unit and receiver
• Connect the product into an outlet on a circuit different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV technician for help
NOTE
This product contains FCC IDs TK4WLE1216V520 and TK4WLE600VX.
2.5.3. United States - AREMA
The product has been tested according to AREMA Part 11.5.1 environmental class J and D
and AREMA Part 11.5.2 exposure class Internal.
2.5.4. Canada - IC
This product complies with Industry Canada’s license-exempt RSSs. Operation is subject to
the following two conditions:
• This product may not cause interference.
• This product must accept any interference, including interference that may cause
undesired operation of the product.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
• l’appareil ne doit pas produire de brouillage.
• l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Ibex-RT-610 Series 9

NOTE
This product contains the IC Certification numbers 7849A-WLE600VX
and 7849AWLE1216V520.
2.5.5. Simplified Declaration of Conformity
Hereby, Westermo declares that this product is in compliance with applicable EU directives
and UK legislations. The full declaration of conformity and other detailed information is
available at www.westermo.com/support/product-support.
Figure 2. The European Conformity and the UK Conformity Assessment markings
10 Ibex-RT-610 Series

3. Product Description
3.1. Product Description
The Ibex-RT-610 is a dual concurrent 802.11ac MU-MIMO Wave1 / Wave2 solution for
onboard and infrastructure Wi-Fi installations in public transport and harsh industrial
environments.
Figure 3. Ibex-RT-610-LV/Ibex-RT-610-HV block diagram
The Westermo configuration management tool, WeConfig, can be used for discovery and
basic configuration and maintenance. The configuration can be done via SNMP or via
WebGUI. The status information is available in local LED status indicators, and through
SNMP/WebGUI.
The Ibex-RT-610 access point is designed to withstand tough environmental conditions and
can be remotely managed using web browser or SNMP management tools.
Integrating hardware, software and network design support tools, this router platform
offers advanced capabilities, the lowest total cost of ownership and will create the most
reliable and resilient networks.
The access point is engineered to maintain uninterrupted data communication, even in
exceptionally harsh environments. Tested and certified to withstand extreme temperatures,
vibrations and shocks, these routers only use industrial grade components which
contributes towards a market leading mean time between failure (MTBF), maximized
service life, and reduced operational and life cycle costs.
Ibex-RT-610 Series 11

3.2. Available models
Art. no. Model Region PoE Port Rated current
3623-073001 Ibex-RT-610-LV EU Europe X2 24 VDC
3623-073002 Ibex-RT-610-LV NA North America X2 24 VDC
3623-073101 Ibex-RT-610-HV EU Europe - 72-110 VDC
3623-073102 Ibex-RT-610-HV NA North America - 72-110 VDC
Table 2. List of available models
3.3. Hardware Overview
3.3.1. Frontside Overview
DC OPR ERR X1 X2
1
4
2
3
5
6
7
No. Description
1 Gigabit Ethernet ports X1 and X2 2 Protective earth terminal
3 Power input DC 4 Front side label
5 Warning symbol for surface
temperatures above +60°C
6 Antenna ports A1 to A4, B1 to B2
7 LED indicators
Table 3. Location of interface ports and LED indicators
3.3.2. Front Side Label
Ibex-RT-xxx-xx EU
Power: 24VDC, 0.6A
3623-075001 00001089 2012
321 4
12 Ibex-RT-610 Series

No. Description Remarks
1 Article number Example of article number
2 Serial number Example of serial number
3 Manufacturing date The Date Format is: YYWW
YY = Manufacturing Year
WW = Manufacturing Week
4 QR code The data matrix is: AAAAAAAAARR-1-VV-SSSSSSSS-YYWW
AAAAAAAAA = Article number
RR = Region code
VV = Product revision
SSSSSSSS = Serial number
YY = Manufacturing Year
WW = Manufacturing Week
Table 4. Front side label
3.3.3. Rear Side Label
Type: Ibex-RT-xxx-xx EU IP66
Art. No: xxx-xxxxxx
NPN: xxxxxx
Max current: 0.6A
Power: 24VDC (±30%)
Country of origin: Switzerland
FCC / IC e-label:
http://<ip-address>
Default IP: 192.168.1.20
Westermo Neratec AG
Postfach 83, CH-8608 Bubikon
Figure 4. Rear side label content
3.3.4. Interface Ports View
A1 A3
A4
B3
B2
B1
A2
X1
X2
DC
X1
X2
DC
2
4
3
1
Ibex-RT-610 Series 13

No. Description No. Description
1 Antennas 2 1000Base-T
3 Grounding point 4 Power
Table 5. Interface ports view
3.4. Connector Information
3.4.1. Power Input Connection
Marking Position Direction Description
DC 1 +DC Positive terminal
2 -
3 -DC Negative terminal
4 -
Housing Shield Chassis of product
(ground)
Table 6. M12 A-coded 4-pin male power connector according to IEC 61076-2-101
NOTE
If the product is powered by PoE, the protective dust cap which is part of
the delivery must be closed to protect the power interface from water or
dust ingress.
3.4.2. Ethernet Ports
The product includes two Ethernet ports X1 and X2 which supports auto-negotiated 10
Mbit/s, 100 Mbit/s and 1000 Mbit/s operation. Automatic MDI/MDIX crossover is
supported for 10BASE-T, 100BASE-T, 1000BASE-T operation.
14 Ibex-RT-610 Series

Marking Position Direction Description
X1/X2 1 In/Out DA+
2 In/Out DA-
3 In/Out DB+
4 In/Out DB-
5 In/Out DD+
6 In/Out DD-
7 In/Out DC-
8 In/Out DC+
Housing Shield Chassis of product (ground)
Table 7. M12 X-coded 8-pin female Ethernet connector according to IEC 61076-2-109
Position Device mode A Device mode B
1 +DC
2 +DC
3 -DC
4 -DC
5 -DC
6 -DC
7 +DC
8 +DC
Table 8. Ethernet PoE connection on X2 (LV-model only)
NOTE
PoE is supported on X2 for the LV product variant only.
NOTE
If the Ethernet function is not used, the protective dust cap which is part
of the delivery must be closed to protect the interface from water or dust
ingress.
3.4.3. Antenna Ports
The antenna connectors are identified on the product with A1 to A4 and B1 to B2. QMA
industrial standard connector is used.
Ibex-RT-610 Series 15

A1 to A4 are used for WLAN Wave 2 communication at 5 GHz. At least A1 must be
connected to an external WLAN antenna if Wave 2 module is used. The antenna
configuration is made through the software interface.
B1 and B2 are used for WLAN Wave 1 communication at 2.4 GHz/5 GHz. At least B1
must be connected to an external WLAN antenna if Wave 1 module is used. The antenna
configuration is made through the software interface.
NOTICE
Any unused antenna ports must be properly terminated with 50 Ohm,
otherwise the product might be damaged when power is applied to a non-
terminated antenna port.
NOTE
To ensure specified IP protection, suitable QMA connectors/cables and
terminations must be used.
3.5. LED Indicators
DC OPR ERR X1 X2
Figure 5. LED indicators
LED Description
DC Power status
OPR Operation status
ERR Error status
X1 Ethernet status for X1 port
X2 Ethernet status for X2 port
Table 9. LED indicators
NOTE
Refer to management guide for detailed LED status indication.
3.6. Dimensions
Dimensions are stated in mm and are regardless variants.
16 Ibex-RT-610 Series

195.4
67
92
180
9.7
7.7
111.4
41
22.7
18
35
31
30.5
19.4
29
29
36
8.5
Figure 6. Dimensional drawing
Ibex-RT-610 Series 17

4. Installation
4.1. Mounting
The product is fixed with the four fixing points located at the corners of the product. M5
or M6 screws are used for the fixation of the product. The screws are tightened with min.
3.0 Nm (fixing screw ISO 898/1, quality class 8.8).
NOTICE
All four specified fixing points must be used for fixing. The installation
surface should be flat to have all fixing points connected to the surface.
NOTE
For indoor installation, consider additional protection against dust to
ensure proper heat dissipation.
NOTE
For outdoor installation, consider additional protection against sun
radiation, dust and dirt to optimize ambient temperature range.
NOTE
Unused connectors must be covered by a protective cap (delivered with
the product), tightened to the specified torque in order to fulfill the
specified ingress protection code.
4.2. Factory Reset
To reset the product into factory default settings, a reset adapter is needed which is
plugged into one of the Ethernet ports X1 or X2 during startup.
Art. no. Description
3623-0799 Factory Reset Plug, X-coded
Factory reset procedure
1. Plug the factory reset adapter to one of the Ethernet interfaces.
18 Ibex-RT-610 Series

2. Power the product.
3. Wait until factory reset adapter is detected. This is indicated by solid ORANGE OPR
LED and RED ERR LED.
4. Remove factory reset adapter within 15 seconds.
5. Successful initiation of the factory reset is indicated by blinking ORANGE OPR LED
and RED ERR LED.
4.3. Earth connection
For correct function, the earth connection at the grounding point needs to be properly
connected to a solid ground. An M6 grounding screw at the housing is used for grounding.
A short wire with a cross section of at least 4 mm2 shall be used. The grounding wire is set
below the rip-lock washer. The nut is fixed for good reliable grounding contact. The
tightening torque of the grounding nut should not exceed 10 Nm.
X1
X2
DC
Figure 7. Earth connection
NOTICE
Do not use equipment without protective earth connection.
4.4. Connection of Cables
Recommended tightening torque for the M12 connectors is 0.6 Nm. All M12 connections
are screw connections.
When connecting the power cable, ensure that the pins are connected correctly before
tightening the power cable to the unit.
NOTE
This product has no replaceable fuse and should be connected via an
external fuse for protection.
Ibex-RT-610 Series 19

4.5. Cooling
This product uses convection cooling. Make sure that it is installed so that the ambient
temperature is within the specified temperature range, e.g. by avoiding obstruction of the
airflow around the product.
It is recommended to install the product in areas where the natural convection airflow is
not blocked and that there is enough spacing around the product.
Figure 8. Installation with reduced natural convection
airflow Figure 9. Installation with natural convection airflow
When operating the product at high ambient temperatures, it is recommended to mount
the product to a metallic base plate to improve the heat dissipation. The base plate
increases the surface to spread the heat.
Figure 10. Improved heat transfer based on fixing plate and natural convection
20 Ibex-RT-610 Series