Westward 1AVP8 User manual

Westward Heavy Duty
Vehicle Stands
Operating Instructions Manual 1AVP8
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
®
Description
Westward Heavy Duty Vehicle Stands are designed to support rated capacity loads,
typically vehicles, over extended periods. Heavy gauge steel frame helps prevent
distortion and twisting. These vehicle stands are designed to meet applicable
ASME/ANSI - PALD Standards.
Note: Rated Capacity is Per Pair ONLY! Use ONLY one pair per vehicle.
General Safety Information
Study, understand,
and follow all
instructions before operating this
device. Rated capacity is per pair! Do
not exceed rated capacity. Use only on
hard level surface. Center load on
saddle. Use as a matched pair to
support one end of a vehicle only. Use
one pair per vehicle. Stands are not to
be used to simultaneously support
both ends or one side of a vehicle. No
alterations shall be made to this
product. Failure to heed these
markings may result in personal injury
and/or property damage.
Before Use
1. Before using this product, read the
operator’s manual completely and
familiarize yourself thoroughly with
the product and hazards associated
with its improper use.
2. Use vehicle stands in pairs on hard
level surface capable of sustaining
rated capacity loads. Use one pair
per vehicle.
3. Make sure load and stands are stable
before working on and around.
4. Inspect before use. Do not use if
bent, broken, cracked, or otherwise
damaged components are noted.
5. Consult vehicle manufacturers service
manual for proper lifting and
support locations.
Operation
TO SUPPORT
1. Adjust height by pulling up
extension tube, then insert support
pin through the appropriate holes in
the extension tube. Ensure the
support pin is secured and properly
engaged.
2. Place stands under support points.
Ensure that load is on center of
saddle.
3. Lower the load slowly onto the
stands. Do not remove lifting device.
4. Ensure vehicle is secure before
working on, around or under. When
used to support vehicle, use wheel
chocks to prevent inadvertent
movement.
TO REMOVE
1. With suitable lift device, raise vehicle
clear of stands.
2. Release support pin and allow
extension tube to glide down to
lowest position.
3. Carefully remove stands, then slowly
lower vehicle with lift device.
Maintenance and Storage
Periodically inspect product. Ensure all
parts move freely. Do not apply oil or
grease to this product. Wipe clean
before use. Store stands in upright
position and in a clean, dry area. Place
stopper in stopper holder on base
section.
NOTE: Other than Label and Manual,
No replacement parts available for this
device. Replace as a matched pair only.
Specifications Min. Max.
Model Capacity Base Size Height Height
1AVP8 22 Ton 9 7/8” x 9 7/8”12 1/4”19 7/8”
Support Pin
Lanyard
Saddle
Base Section
Height Adjustment Holes
Figure 1- Vehicle Stand Components
Handle
SHI 035
Printed in China
07/06
Collar
Bar Holder
Extension Tube

Westward Operating Instructions Manual 1AVP8
Manufactured for Grainger International, Inc.
Lake Forest, IL 60045 U.S.A.
Westward Heavy Duty
Vehicle Stands
®
LIMITED WARRANTY
WESTWARD ONE-YEAR LIMITED WARRANTY.Vehicle Stands , covered in this manual, are warranted by
Westward to the original user against defects in workmanship or materials under normal use for one year
after date of purchase. For limited warranty claim procedures, see PROMPT DISPOSITION below. This
limited warranty gives purchasers specific legal rights which vary from jurisdiction to jurisdiction.
LIMITATION OF LIABILITY.To the extent allowable under applicable law, Westward's liability for
consequential and incidental damages is expressly disclaimed. Westward's liability in all events is limited to
and shall not exceed the purchase price paid.
WARRANTY DISCLAIMER. Westward has made a diligent effort to provide product information and
illustrate the products in this literature accurately; however, such information and illustrations are for the
sole purpose of identification, and do not express or imply a warranty that the products are
MERCHANTABLE, or FIT FOR A PARTICULAR PURPOSE, or that the products will necessarily conform to the
illustrations or descriptions.
Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in
the "LIMITED WARRANTY" above is made or authorized by Westward.
PRODUCT SUITABILITY. Many jurisdictions have codes and regulations governing sales, construction,
installation, and/or use of products for certain purposes, which may vary from those in neighboring areas.
While Westward attempts to assure that its products comply with such codes, it cannot guarantee
compliance, and cannot be responsible for how the product is installed or used. Before purchase and use
of a product, review the product applications, and all applicable national and local codes and regulations,
and be sure that the product, installation, and use will comply with them.
Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation on how long an
implied warranty lasts, consequentially the above limitation may not apply to you; and (c) by law, during
the period of this limited warranty, any implied warranties of implied merchantability or fitness for a
particular purpose applicable to consumer products purchased by consumers, may not be excluded or
otherwise disclaimed.
PROMPT DISPOSITION.Westward will make a good faith effort for prompt correction or other
adjustment with respect to any product which proves to be defective within limited warranty. For any
product believed to be defective within limited warranty, first write or call dealer from whom the product
was purchased. Dealer will give additional directions. If unable to resolve satisfactorily, write to Westward
at address below, giving dealer's name, address, date, and number of dealer's invoice, and describing the
nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was
damaged in transit to you, file claim with carrier.
Manufactured for Grainger International, 100 Grainger Pkwy., Lake Forest, Illinois 60045 U.S.A.