Westwood Design WOODLAND ADVENTURES DP-CR-3101NR-ELM User manual

WOODLAND ADVENTURES
Convertible Crib w/Drawer
Model: DP-CR-3101NR-ELM
CR-3101NR
Assembly Instruction

Congratulations on your purchase of a Westwood product. We take great pride in
the quality and design of our furniture. The safety of your child is our highest
priority. It is important that you read these instructions carefully and completely to
ensure that this product functions as it was designed.
After opening the package, check to see that all the parts are present. If you think
something is missing, please contact your retailer, and they can arrange to have
the missing parts quickly replaced. You can also contact us directly, by calling
1-908-719-4707, or emailing [e-mail]
If any aspect of these instructions is unclear, please contact your retailer or
Westwood Design for assistance.
In addition to meeting our own extensive in-house testing and standards, this crib
has been independently tested to meet JPMA certification standards.
635 N. Billy Mitchell Rd.,
Salt Lake City, UT 84116
Phone: [phone]
www.westwoodbaby.com
Were you expecting more hardware?
This crib uses Westwood’s ground-breaking Always There Hardware system.
The hardware is permanently contained inside the crib, so it is easier to assemble,
there is no hardware to misplace if you put the crib into storage, and no chance of
using the wrong bolt in the wrong location.
We believe this is perhaps the easiest convertible crib in the world to assemble, but
if any part of these instructions is unclear, please contact your retailer or Westwood
for help. For general support and help questions, you can contact Westwood directly
by calling 1-908-719-4707, or emailing [e-mail].
The screws and bolts on your crib are equipped with a locking mechanism under the
head to help prevent loosening, but it’s still a good idea to check them once in a
while and tighten them if needed.

- READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR
FUTURE USE.
- TO REDUCE THE RISK OF SUDDEN INFANT DEATH SYNDROME (SIDS), PEDIATRICIANS
RECOMMEND HEALTHY INFANTS BE PLACED ON THEIR BACK TO SLEEP, UNLESS
OTHERWISE ADVISED BY YOUR PHYSICIAN.
- PREVENT BURNS. KEEP CRIB AWAY FROM OPEN FIRES AND OTHER HEAT SOURCES.
- ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 IN. (69 CM). BY 51-5/8 IN.
(131 CM), WITH A THICKNESS NOT EXCEEDING 6 IN. (15 CM). THE DIMENSIONS OF THE
MATTRESS SHOULD BE TAKEN FROM SEAM TO SEAM.
- DO NOT USE A WATER MATTRESS WITH THIS CRIB.
- NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS A MATTRESS COVER
BECAUSE THE CAUSE SUFFOCATION.
- IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
- FOLLOW WARNINGS ON ALL PRODUCTS IN CRIB.
SUFFOCATION HAZARD:
- INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS TOO
SMALL.
- INFANTS CAN SUFFOCATE ON SOFT BEDDING. NEVER ADD A PILLOW OR COMFORTER.
NEVER PLACE ADDITIONAL PADDING UNDER AN INFANT.
STRANGULATION HAZARD:
- STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND
STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.
- TO PREVENT STRANGULATION, TIGHTEN ALL SCREWS AND BOLTS. A CHILD CAN TRAP
PARTS OF THE BODY OR CLOTHING ON LOOSE SCREWS AND BOLTS.
- DO NOT PLACE CRIB NEAR A WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLE A CHILD.
FALL HAZARD:
- WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT
COULD SERVE AS STEPS FOR CLIMBING OUT.
- WHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE HEIGHT OF 35 IN. (89 CM), THE
CRIB SHALL NO LONGER BE USED.
IMPORTANT:
- CHECK THIS CRIB FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES BEFORE AND AFTER ASSEMBLY AND FREQUENTLY DURING USE. DO NOT
USE CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR DEALER OR CONTACT
WESTWOOD DESIGN: 635 N. BILLY MITCHELL RD., STE. B, SALT LAKE CITY, UTAH 84116,
PHONE: [phone], EMAIL: SUPPORT@WESTWOODBABY
.COM; FOR REPLACEMENT
PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE PARTS.
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.
WARNING

HG
FE
D
C
BA
Parts & Hardware Included
Headboard (x1) Footboard Top (x1)
Footboard Base (x1) Crib End, Left (x1)
Crib End, Right ( x1 ) Day Bed Cap, Left ( x1 )
Day Bed Cap, Right (x1) Mattress Support (x1)

PO
NM
L
K
JI
Parts & Hardware Included
Storage Back Panel (x1) Storage Side Panel, Left (x1)
Storage Side Panel, Right (x1) Storage Center Panel (x1)
Storage Support Legs ( x2 ) Drawer Face, Left ( x1 )
Drawer Face, Right ( x1 ) Drawer Side Panel, Left ( x2 )

XW
VU
T
S
RQ
Parts & Hardware Included
Drawer Side Panel, Right ( x2 ) Drawer Back Panel ( x2 )
Drawer Bottom Panel ( x2 ) JCBC Bolt M6 x 30mm (x14)
Wood Screw M8 x 32mm ( x16 ) Wood Dowel 10 x 30mm ( x6 )
Wood Dowel 8 x 30mm ( x8 ) Handle Screw 20mm ( x4 )
ZY Handle ( x2 ) Allen Wrench (x1)

Required Parts & Hardware
(Z) Allen Wrench
Step 1
(A) Headboard ( x1 )
(D) Crib End, Left ( x1 )
(E) Crib End,Right ( x1 )
A
E
D
Z

Required Parts & Hardware
(Z) Allen Wrench
Step 2
(I) Storage Back Panel (x1)
(J) Storage Side Panel, Left ( x1 )
(K) Storage Side Panel, Right ( X1 )
(L) Storage Center Panel ( x1 )
(M) Storage Support Legs ( x2 )
V
(T) JCBC Bolt M6 x 30mm
( x8 )
(V) JCBC Bolt M6 x 30mm
( x6 )
K
J
L
M
M
I
T
Z
T
T

Required Parts & Hardware
(Z) Allen Wrench
Step 3
(C) Footboard Base (x1)
(T) JCBC Bolt M6 x 30mm
( x6 )
T
Z
C

Required Parts & Hardware
(Z) Allen Wrench
Step 4
Z

Required Parts & Hardware
(Z) Allen Wrench
Step 5
(H) Mattress Support (x1)
Z
H
There are three possible height settings. The mattress support should be at the highest setting for a
newborn, then adjust to the lower position as the child grows and becomes mobile. Once the child is
able to stand, adjust to lowest position.

Required Parts & Hardware
(Z) Allen Wrench
Step 6
(B) Footboard Top (x1)
Z
B

Required Parts & Hardware
(N) Drawer Face, Left (x1)
(O) Drawer Face, Right (x1)
(P) Drawer Side Panel, Left ( x2 )
(Q) Drawer Side Panel, Right ( x2 )
(R) Drawer Back Panel ( x2 )
(S) Drawer Bottom Panel ( x2
Step 7
(U)Wood Screw M8 x 32mm
( x8 )
(W)Wood Dowel 8 x 30mm
( x4 )
U
T
P
R
N or O
Screwdriver - Not provided
U
S
Q
Step 8
S
Tool required -
Screwdriver
(not provided)

Required Parts & Hardware
(Y) Handle ( x2 )
Step 9
(X)Handle Screw 20mm
( x4 )
Y
Screwdriver - Not provided
X
Step 10
Drawer, Left
Drawer, Right

DAY BED CONVERSION
(Z) Allen Wrench
(F) Day Bed Cap, Left (x1)
(G) Day Bed Cap, Right (x1)
Z
Step 1
The day bed can only be used with the mattress support in its lowest position.
Remove the bolts from the footboard using
the allen wrench provided.
Keep the footboard and hardware for future
assembly and use.
Step 2
Day Bed Cap, Right
G
Day Bed Cap, Left
F
Z
Made in Vietnam

- After completing assembly, check that all bolts and screws are secure and tight. Hardware
can become loose over time, so it is your responsibility to periodically check the tightness
of all fasteners for as long as you use the crib.
- Wood is a natural material. As such, it can be affected by changes in temperature and
humidity. Extreme changes in humidity and temperature can cause the wood to warp, swell,
crack, or shrink, thus compromising the structural integrity of the crib and making it
dangerous to use.
- Use caution when placing the crib in storage to avoid extremes in temperature or
humidity. Cribs should always be stored indoors in climate controlled, dry locations.
- Use care when using a vaporizer or humidifier around the crib. Do not aim the vapor at
the crib or any other wooden furniture in the nursery. Avoid using vaporizers or humidifiers
for extended periods of time.
- To clean the crib, wipe with a damp cloth and immediately the dry the surface. Do not use
any chemical cleaners or polishes. Such products can leave a residue on the finish and
come in contact with your child.
- Your crib has a durable and protective non-toxic finish. However, if you decide to refinish
it, you must use a non-toxic finish specified for children’s products. Do not use any toxic
stripping methods to remove the old finish.
CARE AND MAINTENANCE
635 N. Billy Mitchell Rd.,
Salt Lake City, UT 84116
Phone: [phone]
www.westwoodbaby.com