Wetelecom WM-D200 Guide

USB modem Wetelecom WM-D200
Installation and connection manual
MTS Connect 3G
• fast connecting to the Inernet network
• more mobility and freedom of movement
• maximum speed is to 3,1 Mbps
3G CDMA-450

2
ENG
TABLE OF CONTENTS
1. Welcome 3
1.1. The WM-D200 Package 3
1.2. Manufacturer Address 3
1.3. Important Notice 4
1.4. Safety Hazards 4
1.5. Limitation of Liability 6
2. Program Installation 7
2.1. Introduction 7
2.2. Minimum System Requirement 7
2.3. Insert RUIM Card 8
2.4. LED Status Indication 9
2.5. MTS Connect Installation and Uninstall (Windows® XP) 10
2.6. MTS Connect Installation and Uninstall (Windows® Vista/7) 16
3. Descriptions of the MTS Connect GUI 22
3.1. Launch the MTS Connect 22
3.2. Interface overview 22
4. Internet Services 24
4.1. Accessing the Internet 24
5. Settings and Information Query 25
5.1. Version Information 25
5.2. Unlocking the PIN 25
5.3. Enable/Disable PIN 25
5.4. Change PIN Code 26
5.5. Selecting Always On Top mode 26
5.6. Selecting a Pref Mode 26
5.7. Selecting a language 27
6. How to Mac OS 28
6.1. Drivers install 28
7. Product Specification 29
7.1. Technical Specification 29

3
ENG
1. WELCOME
Thank you for purchasing WeTelecom WM-D200 for МТS
CDMA Network!
Before installing the WM-D200, MTS Connect software
and drivers, review this user guide, which outlines the
features and functions of the WM-D200. This device
operates over the high-speed МТS networks in the
450MHz band anywhere!
1.1. THE WM-D200 PACKAGE
The МТS WM-D200 package includes USB Modem WM-
D200 with RUIM tray
1.2. MANUFACTURER ADDRESS
For customer service, contact at [e-mail].
Address : WeTelecom Co., Ltd. The’O Plus #1604
Sanbon-dong, Gunpo City, Kyunggi-do, KOREA
Phone : [phone]

4
ENG
1.3. IMPORTANT NOTICE
Due to the transmission and reception properties
of wireless communications, data can occasionally
be lost or delayed. This can be due to the variation
in radio signal strength that results from changes in the
characteristics of the radio transmission path. Although
data loss is rare, the environment where you operate
the WM-D200 may adversely affect communications.
Variations in radio signal strength are referred
to as fading. Fading is caused by several different
factors including signal reflection, the ionosphere, and
interference from other radio channels.
МТS or its partners will not be held responsible for
damages of any kind resulting from the delays or errors
in data transmitted or received with the WM-D200
device, or failure of the WM-D200 device to transmit
or receive such data.
1.4. SAFETY HAZARDS
Do not operate the WM-D200 device in an environment
that may be susceptible to radio interference resulting
in danger specifically;
1.4.1. Areas where prohibited by the law
Follow any special rules and regulations and obey all
signs and notices. Always turn off the host device and
remove the modem from the USB port when instructed
to do so, or when you suspect that it may cause
interference or danger.

5
ENG
1.4.2. Where explosive atmospheres may be present
• Do not operate the WM-D200 in any area where
a potentially explosive atmosphere may exist. Sparks
in such areas could cause an explosion or fire resulting
in bodily injury or even death. Be aware and comply with
all signs and instructions.
• Users are advised not to operate the WM-D200 while
at a refueling point or service station. Users are
reminded to observe restrictions on the use of radio
equipment in fuel depots (fuel storage and distribution
areas), chemical plants or where blasting operations are
in progress.
• Area with a potentially explosive atmosphere are often
but not always clearly marked. Potential locations can
include gas stations, below deck on boats, chemical
transfer or storage facilities, vehicles using liquefied
petroleum gas (such as propane or butane), areas where
the air contains chemicals or particles, such as grain,
dust or metal powders, and any other area where you
would normally be advised to turn off your vehicle
engine.
1.4.3. Near Medical and life support equipment
Do not operate the WM-D200 in any area where medical
equipment, life support equipment, or near any
equipment that may be susceptible to any form of radio
interference. In such areas, the host communications
device must be turned off. The WM-D200 may transmit
signals that could interfere with this equipment.

6
ENG
1.4.4. On an aircraft, either on the ground or airborne
Many airline regulations state that you must suspend
wireless operations before boarding an airplane. Please
ensure that the host device is turned off and the WM-
D200 is removed from the USB port prior to boarding
aircraft in order to comply with these regulations. The
WM-D200 can transmit signals that could interfere with
various onboard systems and controls.
1.4.5. While operating a vehicle
The driver or operator of any vehicle should not operate
a wireless data device while in control of a vehicle. Doing
so will detract from the driver or operator’s control and
operation of that vehicle. In some countries, operating
such communications device while in control of a vehicle
is an offense.
1.5. LIMITATION OF LIABILITY
The information contained in this document is subject
to change without notice and should not be construed
as a commitment by МТS.
Copyright
©2010 WeTelecom Co., Ltd.

7
ENG
2. PROGRAM INSTALLATION
2.1. INTRODUCTION
This section describes step-by-step method to install
WM-D200 USB MODEM and MTS Connect Software.
2.2. MINIMUM SYSTEM REQUIREMENT
2.2.1. PC Hardware
• Recommend to use PC/Notebook at speed of 300 MHz
or higher. Minimum 233 MHz speed required, Intel
Pentium/Celeron products, AMD K6/Athlon/Duron
products or compatible processors
• Recommend to use 128MB RAM or higher
• Minimum of 64MB memory is required, however, the
performance will be degraded and certain features will
be limited.
• At least 100 MB of free hard disk space is required.
• Motherboard or PCI card that supports USB.
• Video adaptor with Super VGA (800 × 600) or higher
resolution and Monitor
• CD-ROM or DVD Optical Drive
• Keyboard and Mouse

8
ENG
2.2.2. Operating System
• Windows® XP Home or Professional ( with Service Pack 2 )
• Windows® 2000 (with Service Pack 4 for optimal
performances)
• Windows® Vista
• Windows® 7
• Mac OS
Recommended parameters
Windows Update: Keep your computer up to date
2.3. INSERT RUIM CARD
• Insert RUIM card into Tray in proper direction as shown
below.

9
ENG
• Insert Tray into USB Modem. (Double check the position
of the tray.)
2.4. LED STATUS INDICATION
LED COLOR STATUS INFORMATION
Green + Red Internet Connection Status
Green + Blue System IDLE Status
Green only The modem is Powered on but there
is no service

10
ENG
2.5. MTS CONNECT INSTALLATION AND
UNINSTALL (WINDOWS® XP)
2.5.1. MTS Connect Installation (Automatic)
• Connect the modem to USB port. If USB DRIVER is not
present, Modem package Installer will run automatically.
Note:
If Modem package Installer doesn’t work automatically,
Execute RunPack.exe manually.
• Select the desire language as shown below.
• Press [OK] button to proceed. By pressing [Cancel]
button, the installation of MTS Connect program will
be aborted.

11
ENG
• Welcoming message for using MTS Connect Program
window appears.
• Press [Install] Button. The program starts automatically.

12
ENG

13
ENG
• Press [Finish] button once it is done with program
installation.

14
ENG
• It will now start to install the driver. Please check
whether the driver has been installed properly
by checking Device Manager.
(Start Control Panel System Hardware Tab
Device Manager)
If Device Manager for Modems and Ports indicate
as “WeTelecom Mobile USB Modem” and “WeTelecom Mobile
Serial Port 1/2”, then the driver has been successfully installed.
Note:
If installing driver manually, find the driver from Driver
directory. Run Setup.exe to install MTS Connect manually.

15
ENG
2.5.2. USB Driver Uninstall
• Disconnect the modem from USB port before uninstalling
the driver.
• By clicking [Uninstall] in the (Start All program
wetelecom), it will start uninstalling as shown below.

16
ENG
2.6. MTS CONNECT INSTALLATION AND
UNINSTALL (WINDOWS® VISTA/7)
2.6.1. MTS Connect Installation (Automatic)
• Connect the modem to USB port. If USB DRIVER is not
present, Modem package Installer will run automatically.
Note:
If Modem package Installer doesn’t work automatically,
Execute Launcher.exe manually.
• Select the desire language as shown below.
• Press [OK] button to proceed. By pressing [Cancel]
button, the installation of MTS Connect program will
be aborted.

17
ENG
• Welcoming message for using MTS Connect Program
window appears.
• Press [Install] Button. The program starts automatically.

18
ENG

19
ENG
• Press [Finish] button once it is done with program
installation.

20
ENG
• It will now start to install the driver. Please check
whether the driver has been installed properly
by checking Device Manager.
(Start Control Panel System Hardware Tab
Device Manager)
If Device Manager for Modems and Ports indicate
as “WeTelecom Mobile USB Modem” and “WeTelecom Mobile
Serial Port 1/2”, then the driver has been successfully installed.
Note:
If installing driver manually, find the driver from Driver
directory. Execute Setup.exe to install MTS Connect
manually.