Whalen Santa Fe SFKCWMS User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-08-02 Rev. 0001-C Factory: FOCIDI
Santa Fe Kitchen Cart with Metal Shelves
Stock # SFKCWMS
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE
PURCHASE
D
:
/
/

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Santa Fe Kitchen Cart with Metal Shelves (SFKCWMS)
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
GENERAL INFORMATION, TIPS
and
TRICKS
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 20 lb. (9.07 kg)
GENERAL INFORMATION, T
PLACE TV BEHIND THE STOPPER
FITS UP TO MOST 45"FLAT PANEL TVs
MAXIMUM LOAD 100 lb. (45.3 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH
FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND
WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL
TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF
THE UNIT; THE BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING
SURFACE OF THE UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED
FLAT PANEL TVS, OR FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED
RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT,
CAUSING POSSIBLE SERIOUS INJURY.

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Section (Qty. 1) B- Metal Shelf (Qty. 2)
C- Left Front / Right Back Leg D- Right Front / Left Back Leg E- Side Handle
(Qty. 2) (Qty. 2) (Qty. 2)
F- Metal Bar G- Locking Caster H- Swivel Caster I- Stop Rail
(Qty. 4) (Qty. 2) (Qty. 2) (Qty. 1)
(1) Ø1/4" x 5/8" Bolt (2) Ø1/4" x 1-1/4" Bolt (3) Ø1/4" x 1-3/4" Bolt
(Qty. 16+1 extra) (Qty. 8+1 extra) (Qty. 4+1 extra)
(4) Lock Washer (5) Flat Washer (6) Drawer Handle with Bolts
(Qty. 20+1 extra) (Qty. 20+1 extra) (Qty. 2)
4 mm Allen Wrench (Qty. 1) Open Wrench (Qty. 1) Touch-up Pen (Qty. 1)
Tools required: Allen wrench and open wrench (provided), Phillips screwdriver (not provided).

4
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Place the Top Section (A) on a level and protective surface.
3. Remove the utility drawers for the following steps. To remove the drawers, please pull the drawers all
the way out, then simultaneously push the plastic release lever of the ball bearing slides up on one side
and down on the other side, and then pull the drawers completely out.
4. Remove the bolts in Drawer Handles (6), and then use the bolts to attach the Handles to the outside of
the utility drawers by a Phillips screwdriver.
6
6
Drawer Handle with Bolts
(2 used in this step)
⑥
A

5
Assembly Instructions
5. Align and attach four Legs (C and D) to the apron corners of the Top Section (A), using eight 1-1/4"
Bolts (2) with Lock Washers (4) and Flat Washers (5) from inside through the drilled holes on side
panels and screw into place. As shown.
A
D
C
D
CA
C/D
5
4
2
Flat Washer
(8 used in this step)
⑤
Ø1/4" x 1-1/4" Bolt
(8 used in this step)
②
Lock Washer
(8 used in this step)
④

6
Assembly Instructions
6. Attach the Side Handles (E) to the side panels of the Top Section (A) with four 1-3/4" Bolts (3) and
four Washers (4 and 5). As shown.
A
E
E
AE
345
Flat Washer
(4 used in this step)
⑤
Lock Washer
(4 used in this step)
④
Ø1/4" x 1-3/4" Bolt
(4 used in this step)
③

7
Assembly Instructions
7. Fasten the Metal Bars (F) between the Legs (C and D) with eight 5/8" Bolts (1).
A
D
C
D
C
F
F
C/D
F1
Ø1/4" x 5/8" Bolt
(8 used in this step)
①

8
Assembly Instructions
8. Securely screw the Casters (G and H) to the bottom of Legs (C and D) with the enclosed open wrench.
Make sure that two Locking Casters (G) are located at the same short end.
A
C
D
D
C
G
G
H
H

9
Assembly Instructions
9. Flip the assembled unit at its back edges. Fit the Metal Shelves (B) between the Legs (C and D) making
sure the metal tabs overlap the threaded inserts on Legs (C and D). As shown.
10. Fasten the Metal Shelves (B) to the Legs (C and D) using the 5/8" Bolts (1) with the Washers (4 and 5)
through the metal tabs and screw into the legs.
11. Go back and tighten all bolts with the enclosed Allen wrench.
Ø1/4" x 5/8" Bolt
(8 used in this step)
①
Flat Washer
(8 used in this step)
⑤
Lock Washer
(8 used in this step)
④
C
D
C
D
B
B
C
D
D
C
B
B
C/D
B
5
4
1

10
Assembly Instructions
12. Ask for assistance to stand the assembled unit upright.
13. Now, insert the removed drawers into the Top Section (A) to finish the assembly. To place the drawer
back, simply push the ball bearing cart all the way to the end of the slides (on both sides), and align the
slide runners on the drawer with the slides track on the unit. Push it carefully inside until it stops.
NOTE: If the drawer does not go in smoothly, please take it out and repeat the step.

11
Assembly Instructions
NOTE: You must install the Strip Stopper to prevent the TV from tipping when placing your flat panel
television directly on the console.
14. Remove the paper backing of Stop Rail (I), then properly align the Stop Rail with the top edge of the
stopper template on Top Panel (A). Press down on the Stop Rail to help adhesion.
15. Carefully remove the stopper template from the Top Panel (A).
I
I
I
A
A

12
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2016-08-02 Rev. 0001-C Fábrica: FOCIDI
Carro para cocina Santa Fe con repisas de metal
Serie # SFKCWMS
ENSAMBLE REQUERIDO POR ADULTO
Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a
la tienda que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora Estandar del Pacífico: 8:30 a.m. - 4:30 p.m., Lunes a Viernes
O visite nuestra página 24 horas al dia, 7 días a la semana para la asistencia
www.whalenstyle.com
O por correo [e-mail]
LOTE NÚMERO:
FECHA DE COMPRA: / /_____

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Carro para cocina Santa Fe con repisas de metal (SFKCWMS)
HECHO EN CHINA
1. Por favor, lea las instrucciones de ensamble antes de montar este producto.
2. Para evitar daños, monte el producto sobre una superficie plana y firme y protector.
3. Mantenga el herraje separado del alcance de los niños.
4. Por favor, espera hasta que todos los pasos sean completados antes de apretar los tornillos.
5. Asegúrese de que todos los tornillos estén bien apretados antes de que la unidad se utiliza.
PARA LA MAYORÍA DE TV’s DE 45"
PANTALLA PLANA
CARGA MÁXIMA
1
00
lb. (
45
.
3
kg)
MÁXIMAS CARGAS RECOMENDADAS
INFORMACION GENERAL, RECOMENDACIONES Y TRUCOS
CARGA MÁXIMA 50 lb. (22.6 kg)
CARGA MÁXIMA 20 lb. (9.07 kg)
GENERAL INFORMATION, T
PONER
LA
TV DETRÁS DEL TOPE
ESTA UNIDAD NO DEBE UTILIZARSE CON TV’S CRT O DE TUBO.
UTILIZARSE UNICAMENTE CON TELEVISIONES DE PANTALLA PLANA Y EQUIPO DE
AUDIO/VIDEO QUE TENGA LA MEDIDA/PESO RECOMENDADOS. NUNCA UTILIZAR CON TV’S
MAS GRANDES/PESADAS DE LAS RECOMENDADAS. PARA EVITAR INESTABILIDAD COLOQUE
EN EL CENTRO DE LA UNIDAD; LA BASE DE LA TELEVISIÓN DEBE DE REPOSAR SOBRE LA
SUPERFICIE DE SOPORTE DE LA UNIDAD SIN REBASAR LAS ORILLAS. TV’S PANTALLA
PLANA IMPROPIAMENTE COLOCADAS, TV’S PANTALLA PLANA O EQUIPO QUE SOBREPASA
LAS MEDIDAS Y PESOS RECOMENDADOS PUEDE CAERSE Y/O ROMPER LA UNIDAD,
CAUSANDO POSIBLES DAÑOS O LESIONES.

3
Lista de Partes y Herraje
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de
iniciar el ensamblado .
A- Sección superior (Cant. 1) B- Repisa de metal (Cant. 2)
C- Pata frontal izq/posterior der. D- Pata frontal der./posterior izq. E- Jaladera lateral
(Cant. 2) (Cant. 2) (Cant. 2)
F- Barra de metal G- Rueda con freno H- Rueda giratoria I- Riel tope
(Cant. 4) (Cant. 2) (Cant. 2) (Cant. 1)
(1) Tornillo de Ø1/4" x 5/8" (2) Tornillo de Ø1/4" x 1-1/4" (3) Tornillo de Ø1/4" x 1-3/4"
(Cant. 16+1 extra) (Cant. 8+1 extra) (Cant. 4+1 extra)
(4) Arandela presión (5) Arandela plana (6) Jaladera de cajón c/tornillos
(Cant. 20+1 extra) (Cant. 20+1 extra) (Cant. 2)
Llave 4 mm Allen (Cant. 1) Llave española (Cant. 1) Plumón de retoque (Cant. 1)
Herramienta Requerida : Llave Allen y llave española (proveidas), desarmador estrella (no proveido) .

4
Instrucciones de ensamble
1. Desempaque la unidad y confirmar que tiene todo el herraje y las piezas necesarias .
2. Coloque la sección superior (A) sobre una superficie plana y protegida.
3. Retire los cajones para los siguientes pasos. Para quitar los cajones, por favor tirar de los cajones de
todo el camino, a continuación, pulse simultáneamente la palanca de liberación de plástico del cojinete
de baleros de las correderas en un lado hacia arriba y el otro hacia abajo, y luego tirar de los cajones
completamente hacia afuera.
4. Retire los tornillos en las jaladeras de cajones (6) y, a continuación, utilizar los tornillos para fijarlas en
el exterior de los cajones con un destornillador estrella.
6
6
Jaladera de cajón c/tornillo
(2 usados en este paso)
⑥
A

5
Instrucciones de ensamble
5. Alinear y adjuntar cuatro patas (C y D) a las esquinas del delantal de la sección superior (A), utilizando
ocho tornillos de 1-1/4" (2) con arandelas presión (4) y arandelas planas (5) desde el interior a través de
los agujeros perforados en los paneles laterales y fijar en su lugar. Tal como se muestra.
A
D
C
D
CA
C/D
5
4
2
Arandela plana
(8 usados en este paso)
⑤
Tornillo de Ø1/4" x 1-
1/4"
(8 usados en este paso)
②
Arandela presión
(8 usados en este paso)
④

6
Instrucciones de ensamble
6. Coloque las jaladeras laterales (E) a los paneles laterales de la sección superior (A) con cuatro de
tornillos de 1-3/4" (3) y cuatro arandelas (4 y 5). Tal como se muestra.
A
E
E
AE
345
Tornillo de Ø1/4" x 1-3/4"
(4 usados en este paso)
③
Arandela plana
(4 usados en este paso)
⑤
Arandela presión
(4 usados en este paso)
④

7
Instrucciones de ensamble
7. Fijar las barras de metal (F) entre las patas (C y D) con ocho tornillos de 5/8" (1).
A
D
C
D
C
F
F
C/D
F1
Tornillo de Ø1/4" x 5/8"
(8 usados en este paso)
①

8
Instrucciones de ensamble
8. Fijar las ruedas (G y H) a la parte inferior de las patas (C y D) con la llave española. Asegúrese de que
dos ruedas con freno (G) se encuentran en el mismo extremo corto.
A
C
D
D
C
G
G
H
H