WHD VBI10 User manual

This produ t supports all CE-
marking riteria. The de laration
of onformity ertifi ate an be
obtained from WHD.
WHD are members of the INTERSEROH association.
We participate in the dual system as well as other
industry-specific solutions. Therefore, plastic, metal
and electronic parts can all be recycled.
Thank you for buying our Voi e Bridge Inter om Kit.
Please read this manual arefully, espe ially the safety and se urity information.
Manual VoiceBridge Set
Applicable for 111-020-04-200-02
VBI10 (voi e bridge internal)
VBE10 (voi e bridge external)
Used in pare VBI10 and VBE10
Power Supply 12V DC

3 W
Mi rophone with AEC + NR
Operation Temperature -20~50

Operation Humidity 5%~90% RH
Storage Temperature -30~60

Prote tion lass IP 33
Housing Material ABS
Dimensions 110.5 x 86 x 26mm
10 9 8 8
VBI10 : VBE10:
Product Outline
Installation diagram
Staff Customer
VBI10 VBE10
Safety Instructions  Improper handling may void warranty!
 Make sure turn off all power at the breaker before performing any wiring work.
 Do not apply 110VAC or 230VAC. Use only the power supply unit indi ated in do ument requirement.
 The devi e must only be installed and put into servi e by qualified ele tri al personnel.
 When using this produ t, basi safety pre autions should always be followed to redu e the risk of fire ele tri sho k or personal injury.
Do not use this produ t near water.
2
4
5
7
1
2
3
4
6*
7
LED status indicator
Operation
VBI10 LED
Staff
(Green/Red)
VBE10 LED
Customer
(Green/Red)
Standby Green on/ Red off Green on/ Red on
Mi rophone, a tivated by
IR-sensor Green on/ Red off
Mute key tou hed Green on/ Red on
Switching power Supply description
Input: 100~240V AC, 50/60 Hz
Output: 12V DC, 1A
1
*: This key and fun tion is optional.
No. Description
1 Potentiometer for volume adjustment ( only by ommissioning )
2 Speaker
3 Proximity sensor / IR-sensor
4 LED status indi ator
5 Mute key to dea tivate/ a tivate the Mi rophone
6* Help key as attention signal
7 Mi rophone
8 Conne tion so kets
9 Power swit h
10 12V DC
Version
(Te hni al and opti al
modifi ations reserved)
25.06.2020
- Page 1 -
Operation
Technical Parameter
Brief Introduction
The Voi eBridge Inter om Kit onsists of one internal unit and one
external unit, mainly used to fa ilitate onversations when the
speakers are separated by a wall, a pie e of glass/plexiglass sheet, …
et ., for example at ashier or servi e ounters.
Scope of delivery
1 X Voi eBridge internal (staff)
1 X Voi eBridge external ( ustomer)
1 X Swit hing power Supply with 2m able
1 X Cable 1m
1 X Manual
WHD - Wilhelm Huber+Söhne GmbH+Co.KG
Bismar kstr. 19
D-78652 Deißlingen
Support +49 74 20 / 8 89-0
Fax +49 74 20 / 8 89-51 E-Mail: [email protected]
Web: www.whd.de

This produ t supports all CE-
marking riteria. The de laration
of onformity ertifi ate an be
obtained from WHD.
WHD are members of the INTERSEROH association.
We participate in the dual system as well as other
industry-specific solutions. Therefore, plastic, metal
and electronic parts can all be recycled.
Version
(Te hni al and opti al
modifi ations reserved)
25.06.2020
- Page 2 -
Installation and setting
Step 4. Adjust the volume of the devi es with a mini Phillips
s rewdriverwhen ne essary.
Note: the volume of the devi es has been adjusted before leav-
ing the fa tory.
Step 3. Conne t the internal unit to the swit hing power supply
and plug in. The Inter om Kit measures itself briefly on the envi-
ronment and is then ready for use.
Step 5.
 The external unit for the ustomer (VBE10) omes with an
in luded infrared sensor that a tivates the mi rophone, if a
person at a distan e from about 80-100 m ist dete ted.

The IR sensor an be dea tivated / rea tivated by pressing
the reset button using a needle like obje t. The red LED will
turn on/off during this pro ess.
Step 1. Conne t the internal unit and the external unit with the
able supplied.
Contents of package
Manual VoiceBridge Set
Applicable for 111-020-04-200-02
VBI10 (voi e bridge internal)
VBE10 (voi e bridge external)
Thank you for buying our Voi e Bridge Inter om Kit.
Please read this manual arefully, espe ially the safety and se urity information.
Operation
Step 2. Tear off the prote tion paper on the ba k of the units,
and then put the devi es to the right position (as lose as pos-
sible to the speaker) and press them tightly.
E-Mail: [email protected]
Web: www.whd.de
WHD - Wilhelm Huber+Söhne GmbH+Co.KG
Bismar kstr. 19
D-78652 Deißlingen
Support +49 74 20 / 8 89-0
Fax +49 74 20 / 8 89-51