Whelen Engineering Company TIR3 Super-LED/M4 User manual

Page 1
TRUNK
TRUNK HINGE
TRUNK
HINGE BOLTS
(10mm Socket)
FIG. 2
Optional: .156" Diameter hole for
customer supplied sheet metal
screw for extra reinforcement
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Fax: [phone]
FIG. 1
Automotive: Lightheads
Installation Guide:
TIR3™ Super-LED®/M4 Lighthead Mounting Bracket
Trunk Mount - Ford Crown Victoria
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: auto[email protected]om
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]
Installation:
1. Loosen (do not remove) the upper trunk hinge bolt on one side of the
vehicle enough to slide the bracket into place as shown.
2. Slide the bracket under the bolt and tighten the bolt firmly.
3. Ty-wrap the wires to the trunk hinge as you extend them to your power
source, being very careful that the wires won’t be pinched when you
open and close the trunk.
4. Repeat this procedure for the other side of the vehicle. Refer to the
instructions included with your lighthead for wiring information.
©2004 Whelen Engineering Company Inc.
Form No.13955B (022410)
This bracket will mount to the inside of the trunk
using one of the two bolts that hold the trunk
hinges on.
WARNING: Install the brackets on one side of
the vehicle at a time. If you loosen both trunk
hinge bolts at the same time the trunk will
shift and will not line up properly.
For warranty information regarding this product, visit www.whelen.com/warranty
TRUNK
TRUNK HINGE
TRUNK
HINGE BOLTS
(10mm Socket)
FIG. 2
Optional: .156" Diameter hole for
customer supplied sheet metal
screw for extra reinforcement
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Fax: [phone]
FIG. 1
Automotive: Lightheads
Installation Guide:
TIR3™ Super-LED®/M4 Lighthead Mounting Bracket
Trunk Mount - Ford Crown Victoria
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: auto[email protected]om
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]
Installation:
1. Loosen (do not remove) the upper trunk hinge bolt on one side of the
vehicle enough to slide the bracket into place as shown.
2. Slide the bracket under the bolt and tighten the bolt firmly.
3. Ty-wrap the wires to the trunk hinge as you extend them to your power
source, being very careful that the wires won’t be pinched when you
open and close the trunk.
4. Repeat this procedure for the other side of the vehicle. Refer to the
instructions included with your lighthead for wiring information.
©2004 Whelen Engineering Company Inc.
Form No.13955B (022410)
This bracket will mount to the inside of the trunk
using one of the two bolts that hold the trunk
hinges on.
WARNING: Install the brackets on one side of
the vehicle at a time. If you loosen both trunk
hinge bolts at the same time the trunk will
shift and will not line up properly.
For warranty information regarding this product, visit www.whelen.com/warranty

Page 2
Bracket
(M4)
Round Hole
Screw Grommet
Gasket
M4 Lighthead
Flange
#8x1"
PPHSMS
Screw
Trunk
Hinge Bolt
TIR3™ Super-LED
Lighthead
Bracket
(TIR3)
6-32 x 3/8"
PPHMSSS
Flange
Trunk
Hinge Bolt
Bracket
(M4)
Round Hole
Screw Grommet
Gasket
M4 Lighthead
Flange
#8x1"
PPHSMS
Screw
Trunk
Hinge Bolt
TIR3™Super-LED
Lighthead
Bracket
(TIR3)
6-32 x 3/8"
PPHMSSS
Flange
Trunk
Hinge Bolt