Whirlpool AMAP101AB User manual

For questions about features, operation/performance,
parts, or service, call: 1-800-207-1156.
In Canada, for assistance, installation, or service,
call: 1-800-207-1156.
Si tiene preguntas respect o a las características,
funcionamiento, rendimiento, partes, o servicio técnico,
llame al: 1-800-207-1156
Au Canada, pour assistance, installation, ou service,
composez le : 1-800-207-1156
Portable Air Conditioner
Use and Care Guide
Table of Contents
Table des matières
Climatiseur
Guide d’utilisation et d’entretien
Acondicionador de Aire para
Manual de uso y cuidado
Índice
AIR CONDITIONER SAFETY ........................................... 2
INSTALLATION REQUIREMENTS................................... 2
PARTS AND FEATURES .................................................. 3
INSTALLATION INSTRUCTIONS..................................... 5
USING YOUR AIR CONDITIONER.................................. 8
CARE AND CLEANING.................................................. 10
TROUBLESHOOTING.................................................... 12
SPECIFICATIONS........................................................... 13
ASSISTANCE OR SERVICE........................................... 13
XLS PRODUCTS WARRANTY FOR
AMANA®AIR CONDITIONERS...................................... 14
Models/Modèles/Modelos:
AMAP101AB/AMAP101AD/AMAP101AW & AMAP121AB/AMAP121AD/AMAP121AW
®/™ ©2018Amana. All rights reserved. Manufactured under license by XLS Products, Pennsylvania.
®/™ ©2018Amana. Tous droits réservés. Fabriqué sous licence par XLS Products, Pennsylvanie.
®/™ ©2018Amana. Todos los derechos reservados. Fabricado bajo licencia por XLS Products, Pennsylvania.
SÉCURITÉ DU CLIMATISEUR....................................... 15
EXIGENCES D’INSTALLATION ..................................... 15
PIÈCES ET CARACTÉRISTIQUES ................................ 16
INSTRUCTIONS D’INSTALLATION............................... 18
UTILISATION DE VOTRE CLIMATISEUR ..................... 21
ENTRETIEN ET NETTOYAGE........................................ 23
DÉPANNAGE .................................................................. 25
SPÉCIFICATIONS........................................................... 26
ASSISTANCE OU SERVICE........................................... 27
GARANTIE DE XLS PRODUCTS POUR
LES CLIMATISEURS AMANA®...................................... 28
SEGURIDAD DEL ACONDICIONADOR DE AIRE ........ 29
REQUISITOS DE INSTALACIÓN ................................... 29
PIEZAS Y CARACTERÍSTICAS ..................................... 30
INSTRUCCIONES DE INSTALACIÓN ........................... 32
USO DE SU ACONDICIONADOR DE AIRE .................. 35
CUIDADO Y LIMPIEZA .................................................. 37
SOLUCIÓN DE PROBLEMAS........................................ 39
ESPECIFICACIONES ..................................................... 40
ASISTENCIA O SERVICIO TÉCNICO............................ 41
GARANTÍA DE XLS PRODUCTS PARA
ACONDICIONADORES DE AIRE AMANA®.................. 42
95111_AMAP10_12AW_Amana_Final v03.indd 1 6/8/2016 2:46:56 PM

2
AIR CONDITIONER SAFETY
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic precautions:
SAVE THESE INSTRUCTIONS
Unplug air conditioner before servicing.
Use two or more people to move and install air conditioner.
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
INSTALLATION REQUIREMENTS
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Check the location where the air conditioner will be installed.
Make sure you have everything necessary for correct installation.
The location should provide:
■Grounded electrical outlet within 6 ft (183 cm) of where the
power cord exits the air conditioner.
NOTE: Do not use an extension cord.
■Free movement of air in room to be cooled.
■A large enough opening for the air conditioner. Installation
parts are supplied for double-hung windows.
■Allow at least 10" (25 cm) clearance from walls and furniture.
NOTE: Cabinet louvers must not be obstructed. Do not place the
unit in front of drapes or curtains; they may block the air intake.
Disposing of the unit:
■When you need to dispose of the unit, consult with your local dealer or local recycling center for information on how to
dispose of the unit in a environmentally responsible manner.
■Please recycle or dispose of the packaging material for product in an environmentally responsible manner.
95111_AMAP10_12AW_Amana_Final v03.indd 2 6/8/2016 2:46:57 PM

3
Installation Parts Supplied
Check that all parts are included in parts package.
A. Window insert panel (1) B. Flexible vent hose
assembly (1)
A
PARTS AND FEATURES
Front View
Casters
Control Panel
Handle
Air Outlet
Back View
Internal
tank drain
Drain tting
(for dehumidier
mode)
Air outlet
(heat
exchanger)
Air intake
(condenser)
Air Intake (evaporator)
Upper air lter
(behind grille)
Lower air lter
Cord wrap
Remote
storage
B
95111_AMAP10_12AW_Amana_Final v03.indd 3 6/8/2016 2:46:58 PM

4
Electrical Requirements
■115-volt (103.5 min. - 126.5 max.)
■0-12 amps
■15-amp time-delay fuse or circuit-breaker
■If there is a “Single Circuit Only” label on the unit,
use on a dedicated single-outlet circuit only. If a
dedicated single-outlet circuit is not available, then
it is the customer’s responsibility to have a single-
outlet circuit installed by a qualied electrician.
■If there is no “Single Circuit Only” label on the
unit, the unit may be used on any branch circuit
of correct voltage and adequate current
protection rating.
Recommended Grounding Method
This air conditioner must be grounded. This air conditioner is
equipped with a power supply cord having a grounded 3-prong
plug. To minimize possible shock hazard, the cord must be
plugged into a mating, grounded 3-prong outlet, grounded in
accordance with all local codes and ordinances. If a mating outlet
is not available, it is the customer’s responsibility to have
a properly grounded 3-prong outlet installed by a qualied
electrical installer. It is the customer’s responsibility:
■To contact a qualied electrical installer.
■To assure that the electrical installation is adequate and
in conformance with National Electrical Code, ANSI/NFPA
70 — latest edition, and all local codes and ordinances.
Copies of the standards listed may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269
Power Supply Cord
NOTE: Your air conditioner’s power supply cord may differ from
the one shown. This portable air conditioner is equipped with
a power supply cord required by UL. This power supply cord
contains state-of-the-art electronics that sense leakage current.
If the cord is crushed, the electronics detect leakage current and
power will be disconnected in a fraction of a second.
To test your power supply cord:
1. Plug power supply cord into a grounded 3-prong outlet.
2. Press RESET (on some models, a green light will turn on).
3. Press TEST.
4. Press and release RESET.
The power supply cord is ready for operation.
Electrical Requirements
The electrical ratings for your air conditioner are listed on the
model and serial number label. The model and serial number
label is located on the back of the air conditioner cabinet.
A. Reset button
B. Test button
NOTES:
■The Reset button must be pushed in for proper operation.
■The power supply cord must be replaced if it fails to trip when
the test button is pressed or fails to reset.
■Do not use the power supply cord as an off/on switch. The
power supply cord is designed as a protective device.
■A damaged power supply cord must be replaced with a new
power supply cord obtained from the product manufacturer
and must not be repaired.
■The power supply cord contains no user-serviceable parts.
Opening the tamper-resistant case voids all warranty and
performance claims.
A
B
95111_AMAP10_12AW_Amana_Final v03.indd 4 6/8/2016 2:46:59 PM

5
Prepare Air Conditioner for Installation
INSTALLATION INSTRUCTIONS
WARNING
Excessive Weight Hazard
Use two or more people to move and install
air conditioner.
Failure to do so can result in back or other injury.
Remove Packaging Materials:
■Handle the air conditioner gently while unpacking the unit.
■Remove the carton top and lift the air conditioner from the
base pad.
■Remove tape and glue residue from surfaces before turning
on the air conditioner. Rub a small amount of liquid dish soap
over the adhesive with your ngers. Wipe with a damp cloth
and dry.
■Do not use sharp instruments, rubbing alcohol, ammable
uids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your air conditioner.
■Be sure to check all packing materials for parts before
discarding.
■Dispose of/recycle packaging materials in an appropriate way.
Position the window slider panel in the window opening.
Install Window Slider Panel
1. Position slider panel in window
Slider panel
Extend the slider panel extension until it lls the window opening.
Be sure the vent opening in the slider panel is not covered.
If the window is too narrow to fit the slider panel without
blocking the vent opening:
1. Remove the slider panel extension from the slider panel.
2. Using a hand saw, cut the slider panel extension to t the
window opening. Leave as much panel as possible without
covering the vent opening(s) in the slider panel.
3. Slider the slider panel extension back into the slider panel.
Window Opening Requirements
This air conditioner may be used with standard double-hung
windows and with vertical sliding windows.
Double-Hung Window Opening Measurements:
■265⁄8" (67.6 cm) minimum to 52" (1.35 m) maximum
opening width
■4" (10.2 cm) minimum opening height
Vertical Sliding Window Opening Measurements:
■4" (10.2 cm) minimum opening width
■265⁄8" (67.7 cm) minimum to 52" (1.35 m) maximum
opening height
IMPORTANT: For window openings between 265⁄8" (67.6 cm)
and 37" (94 cm), it will be necessary to cut the slider panel
extension to t the window opening.
2. Extend and secure slider panel
Slider panel
extension
95111_AMAP10_12AW_Amana_Final v03.indd 5 6/8/2016 2:47:00 PM

6
Turn the drain port retainer plug counterclockwise to remove,
then pull out the rubber drain plug.
1. Remove drain fitting plug
Drain Hose Connection (optional)
When using the air conditioner for dehumidication only, you may
attach a hose (not included) for water drainage into a oor drain.
The drain hose must be below the drain port on the back of the
air conditioner.
Insert the round connector of the vent hose into the exhaust
port on the back of the air conditioner. Turn counterclockwise to
lock into place.
1. Attach vent hose to air conditioner
Position the air conditioner in the desired location.
Extend the vent hose enough to reach from the air conditoner
to the window. Be sure there are no sharp bends or kinks in the
hose.
Press the window connector end of the vent hose into the
opening on the slider panel as shown. It will clip into place.
2. Attach vent hose to slider panel
Window
connector
Slider panel
Assemble Vent Hose
Insert the drain hose into the drain tting on the air conditioner.
Insert the other end of the drain hose into a oor drain or other
suitable drain.
2. Install drain hose
95111_AMAP10_12AW_Amana_Final v03.indd 6 6/8/2016 2:47:00 PM

7
Plug into a grounded 3-prong outlet.
Press the RESET button on the power supply cord.
See “Electrical Requirements.”
Electrical Connection
1. Plug into grounded 3-prong outlet
NOTE:
■Do not drop the remote control; this may damage the remote
control.
■Remove the batteries if the remote control is not used for a
month or longer.
■Dispose of used batteries responsibly.
NOTE: The remote uses two AAA 1.5V batteries (included).
Replace batteries when the battery indicator in the upper right
corner of the remote display is empty.
To remove the batteries:
Remove the battery compartment cover and remove the
batteries.
To reinstall the batteries:
Place the batteries into the battery compartment as shown, then
reinstall the cover.
Installing/replacing the batteries
in the remote
95111_AMAP10_12AW_Amana_Final v03.indd 7 6/8/2016 2:47:01 PM

8
USING YOUR AIR CONDITIONER
Turning the Air Conditoner ON or OFF
Press POWER to turn the air conditoner on or off.
IMPORTANT:
■If you turn off the air conditioner, wait at least
3 minutes before turning it back on. This prevents
the air conditioner from blowing a fuse or tripping a
circuit breaker.
■The recommended operating temperature range is between
44°F (7°C) and 95°F (35°C). Operating the air conditioner
above or below this range may cause the the inside
evaporator coil to freeze up, and the air conditioner will not
operate properly.
NOTE: In the event of a power failure, your air conditioner will
operate at the previous settings when the power is restored.
Display
During normal operation, display will
show the current room temperature
and the mode and settings. When the
UP or DOWN button is pressed, the
unit will display the set temperature or
delay time.
Selecting the Mode
The Mode button has three settings:
■Cool
■Dehumidify
■Fan
Press the MODE button until the indicator light below the desired
setting is lit.
Cooling (COOL) Mode
During Cooling mode, the air conditioner cools air from
the room and vents hot air to the outdoors through
the vent hose(s). Adjust fan speed and the temperature setting
to t your desired comfort level. Temperature setting range is
61°F–90°F (16°C–32°C).
IMPORTANT: The vent hose(s) must exhaust to the outdoors
when using Cooling mode.
Dehumidify (Dry) Mode
Air is dehumidied as it passes through the unit,
without being in full cooling mode. The fan speed is set
automatically to LOW and cannot be adjusted .
IMPORTANT: For best results, the continuous drain hose should
be connected.
Fan (FAN) Mode
In this mode, only the fan will run. Air is circulated through the
room with no cooling.
NOTE: The air conditioner does not need to be vented to the
outdoors in Fan mode.
Selecting the Fan Speed
The Fan has 3 speed settings:
■Low
■Medium
■High
Press the FAN button until the desired setting is selected.
Adjusting the Temperature
Press the UP or DOWN buttons to
adjust the set temperature up or down
in 1° increments. Temperature setting
range is 61°F–90°F (16°C–32°C). After
10 seconds, the display will return to the current room
temperature.
NOTE: Temperature may only be adjusted in Cooling mode.
When in TIMER mode, pressing the UP or DOWN buttons will
adjust the delay time for the air condtioner to shut off or turn on.
Appearance may vary.
95111_AMAP10_12AW_Amana_Final v03.indd 8 6/8/2016 2:47:01 PM

9
Using the Timer
Auto Shut-Off
You can set the air conditoner to shut off
automatically after a set number of hours,
up to 24 hours.
To set Auto Shut-Off:
1. With the air conditioner in fan mode, press Timer.
2. Use the UP and DOWN buttons to select the number of hours,
up to 24 hours. The Timer indicator will remain displayed to let
you know the timer is set.
3. After the set time, the air conditioner will turn off automatically.
Auto Start
You can set the air conditioner with the TIMER to start
automatically after a set number of hours.
1. With the air conditoner OFF, press TIMER.
2. Use the UP or DOWN button to select the number of hours
before the air conditioner should turn on, up to 24 hours.
The TIMER indicator will be displayed to let you know the
timer is set.
3. After the set time, the air conditioner will start automatically in
Cooling mode with the last temperature and fan settings used.
Other Functions
Bucket Full Warning “FL”
This air conditioner has an internal tank to hold accumulated
water from the condenser. Normally, this water is evaporated and
exhausted to the outside. However, in periods of high humidity,
the internal tank may become full. If this happens, “FL” will
appear in the display, a tone will sound, and the air conditioner
will turn off until the internal tank is emptied. See “Care and
Cleaning”.
Using the Remote Control
The remote control allows you to turn the air conditioner on
and off, as well as select the Mode, Fan Speed, and set the
temperature and time using the same method as the control
panel. The LCD display on the remote will display the current
mode and settings.
Additional functions are only available through the remote.
Switching between Fahrenheit and Celsius:
Press the °C–°F button on the remote to toggle the displayed
units between °F and °C.
Auto Swing Mode:
Pressing the Swing button will toggle Auto Swing mode on
and off. In Auto Swing mode, the air outlet louvers will move
automatically to improve circulation. Auto Swing will appear in
the remote display and the Auto Swing icon will appear in the air
conditioner display.
Normal Operating Sounds
When your air conditioner is operating normally, you may hear
sounds such as:
■Droplets of water hitting the condenser, causing a pinging or
clicking sound. The water droplets help cool the condenser.
■Air movement from the fan.
■Clicks from the thermostat cycle.
■Vibrations or noise due to poor wall or window construction.
■A high-pitched hum or pulsating noise caused by the modern
high-efciency compressor cycling on and off.
NOTE: Remote control
may vary in appearance.
95111_AMAP10_12AW_Amana_Final v03.indd 9 6/8/2016 2:47:02 PM

10
Your new air conditioner is designed to give you many years of
dependable service. This section tells you how to clean and care
for your air conditioner properly.
1. Using a Phillips screwdriver, remove the 4 screws holding the
lter in place.
2. Pull the air lter straight out of the air conditioner.
Reinstalling the air filter:
1. Reinstall the air lter in the air conditioner by reversing
step 2 above.
2. Insert the tabs on the bottom of the air intake cover into the
slots on the air conditioner, then press the top into place until
it clicks to lock.
CARE AND CLEANING
1. Remove the air intake cover
1. Turn off the air conditioner.
2. Remove the air intake cover by pulling the top of the cover
away from the air conditioner, then lifting the bottom tabs out
of the slots on the air conditioner.
2. Remove the air filter
Cleaning the Air Filters
The air lters are removable for easy cleaning. A clean lter helps
remove dust, lint, and other particles from the air and is important
for best cooling and operating efciency. Check the lters every 2
weeks to see whether they need cleaning.
NOTE: For best performance, do not operate the air conditioner
without the lters in place.
Use a vacuum cleaner to clean air lters. If the
air lters are very dirty, wash them in warm
water with a mild detergent.
NOTE: Do not wash the air lters in the
dishwasher or use any chemical cleaners; it may damage the
lters. Air dry the air lters completely before reinstalling to
ensure maximum efciency.
Removing the Upper Air Filter
Removing the Lower Air Filter
1. Remove the lower air filter
1. Turn off the air conditioner.
2. Pull the lower air lter straight out from the back of the air
conditioner.
Reinstalling the air filter:
1. Reinstall the air lter in the air conditioner by reversing
step 2 above.
95111_AMAP10_12AW_Amana_Final v03.indd 10 6/8/2016 2:47:02 PM