Whirlpool G0 User manual
©Service Competence Center
Induction G0
Induction cooktop G0
©Service Competence Center
Table of Contents
Induction G0
Installation
Dimensions 60 cm
Dimensions 77 cm
Standard Installation
Full integrated installation
Electric connection
Operation
Switch ON/OFF
Cooking zone activation
Control panel lock
Timer
Booster
Eco Booster
Automatic function
Indications on display
Power management
Demo Mode
Acoustic Signal
Repair guide line
Housing
Touch control
Zone
Fan
Converter board
Components
Exploded view
Overview components
Overview converter board
ESAM connection
Overview cable connection
Induction coil overview
Induction coil power level
Zone exploded view
NTC
User Interface Artemis 2
Cooling fan
©Service Competence Center
Table of Contents
Marketing Information
Range overview
12NC breakdown
7 safety points
Accessories
Troubleshooting
Failure code type 1
Failure code type 2
Failure code type 3
Failure description
LED and buzzer check
Access main menu
Main menu
ConfigurationG0
Failure Show
Delete Failures
Test program rules
ConfigurationCodes
Wiring diagram
Induction G0
©Service Competence Center
Installation
Installation
Induction G0
G0 needs more air circulation in order to cool down the electronic parts. Therefore mor
free space is needed in the rear of the cooktop.
As well the separate cutout has to be done in the rear of the separation plate underneath
the cooktop.
©Service Competence Center
Installation
Full integrated installation
11.5
6 +/- 0.5
Perimetral Gasket
Silicon
COOKTOP CUT OUT
DIM.
mm
Depth Length Width Length Width
580 Vetroceramic Cooktops Flush Installation 38 580 510 583/560 513/490 -0/+2
770 Vetroceramic Cooktops Flush Installation 39 770 510 773/750 513/490 -0/+2
Induction G0
©Service Competence Center
Installation
Full integrated installation
•Make the cut-out as described and try the fit-in of
the hob
•Before gluing the hob to the worktop remove the
6 screws, which have the screw head on the
outside.
This is important, they are not reachable after
installation!
•Put in the 6 screws with the bigger head from
inside of the frame.
These ones can be loosen easier, when the hob is
installed.
The glass frame will stay in the worktop but the
metal support with the electronic can be removed
by loosing these screws
On the back side there are 2 hooks, no screws
Induction G0
©Service Competence Center
Installation
Electrical connection (hob)
Induction G0
A mains cable is delivered with the
cooktop.
On hob side:
L1, L2 and N1, N2 = VHR connectors
Earth connection = crimp contact
On house side:
L1 and L2 are clamped together in one
cable end sleeve.
N1 and N2 are clamped together in one
cable end sleeve.
In order to allow using the cooktop with
1 phase 230V.
If the cooktop will be connected with 2
phase, the life connection (L1, L2) have
to be cutted and connected one by one.
SC:4810 106 19175 = 1.5m (5x1.5mm²)
SC:4810 106 38939 = 2.5m (5x2.5mm²)
©Service Competence Center
Operation
Switch ON/OFF
Induction G0
Switching the hob ON/OFF
On:
- press the button for approx. 2 seconds
until the cooking zone displays light up.
Off:
- press the same button until the displays switch off
All the cooking zones are deactivated.
If the hob has been in use, the residual heat indicator “H” remains lit until the
cooking zones have cooled down (>40°C glass temperature).
If within 10 seconds of switching on, no function is selected, the hob switches
off automatically.
©Service Competence Center
Operation
Cooking zone activation
Induction G0
Switching on and adjusting cooking zones
Place the pot on the cooking zone
switch the hob on
activate the required cooking zone by pressing the corresponding circular button
“5” appears on the display.
With the Slider (if available) it is possible to select the required power level, from min. 0
to max. 9, or booster “P” if available. To increase the power level, slide your
finger on the slider from left to right several times; to decrease it, slide in the opposite
direction. Alternatively the “+” and “-” buttons can be used.
Deactivation of cooking zones
To switch off the cooking zone, press the corresponding button for more than 3 seconds.
The cooking zone switches off and, if still hot, the letter “H” appears on the zone display.
©Service Competence Center
Operation
Control panel lock
Induction G0
Control panel lock
This function locks the controls to prevent accidental activation of the hob.
Activation of the control panel lock:
- switch the hob on
- press the Timer button for 3 seconds
an acoustic signal and a luminous indicator near the padlock symbol confirm activation.
The control panel is locked except for the switch off function.
Deactivation of the control lock:
repeat the activation procedure.
The luminous dot goes off and the hob is active again.
The presence of water, liquid spilled from pots or any objects resting on the button
below the symbol can accidentally activate or deactivate the control panel lock.
Table of contents
Other Whirlpool Cooktop manuals
Whirlpool
Whirlpool 4454652 User manual
Whirlpool
Whirlpool GJC3034RB02 User manual
Whirlpool
Whirlpool RC8330XTW0 User manual
Whirlpool
Whirlpool AKM 260/IX User manual
Whirlpool
Whirlpool GMA 9522/IX User manual
Whirlpool
Whirlpool AKM 268/IX User manual
Whirlpool
Whirlpool GJC3634HB4 User manual
Whirlpool
Whirlpool GJC3034GQ0 User manual
Whirlpool
Whirlpool RC8300XL User manual
Whirlpool
Whirlpool RCC3024RB03 User manual
Whirlpool
Whirlpool GOA 9523/WH User manual
Whirlpool
Whirlpool RC8536XT User manual
Whirlpool
Whirlpool BUILT-IN MICROWAVE OVEN User manual
Whirlpool
Whirlpool WCE55US6H User manual
Whirlpool
Whirlpool GLS3074V User guide
Whirlpool
Whirlpool RCS2012RS00 User manual
Whirlpool
Whirlpool AKT 797 User manual
Whirlpool
Whirlpool GLT3014GQ2 User manual
Whirlpool
Whirlpool GOA 6423/NB1 User manual
Whirlpool
Whirlpool W10162212A User manual
