Whirlpool WDF550SAAB User manual

DISHWASHER SAFETY ................................................................................ 2
INSTALLATION REQUIREMENTS ............................................................... 2
Location Requirements .............................................................................. 3
Electrical Requirements.............................................................................. 4
Water Supply Requirements....................................................................... 5
Drain Requirements.................................................................................... 5
INSTALLATION INSTRUCTIONS ................................................................. 5
Prepare Cabinet Opening—Existing Utility Hookups ................................ 5
Prepare Cabinet Opening—No Existing Utility Hookups........................... 7
Install Dishwasher.....................................................................................10
Make Electrical Connections—Direct Wire Method ................................12
Make Electrical Connections—Power Supply Cord Method...................12
Connect Dishwasher to Water Supply.....................................................13
Connect Dishwasher to Drain...................................................................13
Attach Dishwasher to Cabinet..................................................................14
Complete Installation................................................................................14
SÉCURITÉ DU LAVE-VAISSELLE.............................................................. 16
EXIGENCES D'INSTALLATION.................................................................. 16
Outillage et composants .......................................................................... 16
Exigences d’emplacement....................................................................... 17
Spécifications électriques ........................................................................ 18
Spécifications de l'alimentation en eau ................................................... 19
Évacuation de l'eau de lavage—Critères à respecter ............................. 19
INSTRUCTIONS D’INSTALLATION........................................................... 19
Préparation de l’espace d’installation entre les placards—Utilisation
des modes de raccordement existants pour canalisations et câblage... 21
Préparation de l’emplacement d’installation entre les placards
lorsque les canalisations et câbles n’ont pas été installés...................... 21
Installation du lave-vaisselle..................................................................... 24
Raccordement au réseau électrique—Câblage direct ............................ 26
Raccordement au réseau électrique—Cordon d’alimentation................ 27
Raccordement à la canalisation d’arrivée d’eau...................................... 28
Raccordement à l’évacuation .................................................................. 28
Immobilisation du lave-vaisselle dans la cavité d’encastrement ............ 28
Achever l’installation................................................................................. 29
IMPORTANT:
Save for local electrical inspector’s use.
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
IMPORTANTE:
Guarde para tenerlas a disposición del inspector de electricidad local.
Instalador: Deje las instrucciones de instalación con el propietario.
Propietario: Conserve las instrucciones de instalación para referencia futura.
IMPORTANT :
Conserver pour consultation par l’inspecteur local des installations électriques.
Installateur : Remettre les instructions d’installation au propriétaire.
Propriétaire : Conserver les instructions d’installation pour référence ultérieure.
UNDERCOUNTER DISHWASHER
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION DU LAVE-
VAISSELLE ENCASTRÉ
Table of Contents / Table des matières
Models/Modèles WDF550SAAW WDF550SAAB WDF550SAAS
W10518038

2
DISHWASHER SAFETY
You need to:
■Slowly open dishwasher door while someone grasps the rear
of the dishwasher. Remove shipping materials. Close
dishwasher door. Latch the dishwasher door shut.
■Observe all governing codes and ordinances.
■Install this dishwasher as specified in these instructions.
■Have everything you need to properly install dishwasher.
■Contact a qualified installer to ensure that dishwasher is
installed to meet all electrical and plumbing national and local
codes and ordinances.
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
Parts Needed
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
WARNING
■Phillips screwdriver
■Flat-blade screwdriver
■Measuring tape or ruler
■¹⁄₂", ³⁄₄" and 1½" (1.3 mm,
1.9 mm and 3.8 cm) hole
saw bits
■Shallow pan
■6" (15.2 cm) adjustable
wrench
■Small tubing cutter
■Level
■Cordless drill
■¹⁄₈" drill bit
■Flashlight
■90º elbow with ³⁄₈" N.P.T.
external threads on one
end
NOTE: The other end
must fit the water supply
line.
■Thread seal tape
■3 UL listed wire nuts
■Copper tubing
(³⁄₈" recommended)
■1¹⁄₂" to 2" (3.8 cm to
5.1 cm) screw-type clamp
■Clamp connector (strain relief)
⁷⁄₈" (22.2 cm) diameter
hole
■1¹⁄₂" to 2" (3.8 cm to
5.1 cm) screw-type clamp
if connecting to waste-tee
to fit

3
Parts Supplied
Check that all parts are included. See separate parts list for
accessories available for your dishwasher.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
Proper installation is your responsibility.
■Contact a qualified installer to ensure that the dishwasher is
installed to meet all electrical and plumbing national and local
codes and ordinances.
■Install the dishwasher as specified in these instructions.
■Have everything you need to properly install dishwasher.
■Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
warranty.
■This dishwasher is manufactured for indoor use only.
■Install and level dishwasher on a floor that will hold the weight,
and in an area suitable for its size and use.
■Install dishwasher in a location with easy access to water,
electricity and drain.
Minimum Clearances
NOTES:
■Corner locations require 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
■A minimum of 25⁵⁄₈" (65.1 cm) is required in front of the
dishwasher to allow the door to open fully.
■Opening should be square, and the floor should be level.
Product Dimensions
Side View
*
* To front of door frame
Rear View
A. #8 x ⁵⁄₈ " Phillips flat-head wood screws
B. Phillips color-matched toekick screws
A. 2" (5.1 cm) minimum clearance
for door opening
B. Dishwasher
C. Countertop
D. 25
⁵⁄₈ " (65.1 cm) minimum
AB
A
B
C
D
24" (61 cm)*
16 5/8"(42.2 cm)
32¹⁄₂" to 34¹⁄₂"
(82.6 to 87.6 cm)
23 5/9"(59.8cm)
■Fully enclosed on both sides, back, and top.
2¹⁄₂" (6.2 cm)

4
Installation Clearances
Cutout Dimensions
* Underside of countertop to floor
NOTES:
■Cut holes in shaded area of cabinet walls or floor for plumbing
and electrical service.
■ADA installation—32¹⁄₂" (82.5 cm) beneath 34" (86.4 cm) high
countertops may be accomplished by adjusting the toekick
and leveling legs.
Electrical Requirements
Contact a qualified electrician.
Ensure that the electrical installation is adequate and in
conformance with all national and local codes and ordinances.
Requirements:
■120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical
supply
■Copper wire only, 2 wire with ground
Recommended:
■Time-delay fuse or circuit breaker
■Separate circuit
Direct Wire Connection
■Use flexible, armored or nonmetalic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
Power Supply Cord Connection
Use Power Supply Cord Kit (Part Number 4317824) marked for
use with dishwashers. Kit contents include:
■UL listed 16 gauge 3-wire power supply cord with
3 prong grounding plug
■Neer C-500 ⁷⁄₈" strain relief
■3 wire connectors
■Part No. 302797 grommet
Follow the kit instructions for installing the power supply cord.
NOTE: Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the dishwasher
opening. Outlet must meet all local codes and ordinances.
IMPORTANT: If you plan to install a garbage disposal, an
additional separate 120-volt, 60 Hz, AC-only, 15- or 20-amp fused
electrical supply is required.
A. All surfaces free from intrusions
24" (61 cm)
minimum
34" to 35"
(86.4 cm to 88.9 cm)
24 (61 cm)
maximum
A
6"
(15.2 cm)
4"
(10.2 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
■For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. The dishwasher is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and
ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
dishwasher is properly grounded. Do not modify the
plug provided with the dishwasher; if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
■For a permanently connected dishwasher:
The dishwasher must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the dishwasher.
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS

5
Water Supply Requirements
■A hot water line with 20-120 psi (138-862 kPa) water pressure.
■120°F (49°C) water temperature at dishwasher.
■³⁄₈" O.D. copper tubing with compression fitting or flexible
braided water supply line.
NOTE: ½" minimum plastic tubing is not recommended.
■90º elbow with ³⁄₈" N.P.T. external pipe threads on one end.
IMPORTANT: Do not solder within 6" (15.2 cm) from water inlet
valve.
Drain Requirements
■Use the new drain hose supplied with your dishwasher.
NOTE: If a longer drain hose is required:
■Use a new drain hose with maximum length of 10 ft (3 m)
that meets all current AHAM/IAPMO test standards
■Use a new drain hose that is resistant to heat and
detergent
■Use a new drain hose that fits the 1" (2.5 cm) drain
connector on the dishwasher.
■Connect drain hose to waste tee or disposal inlet above drain
trap in house plumbing.
■Connect drain hose to house plumbing 20" (50.8 cm)
minimum above the floor.
NOTE: It is recommended that the drain hose either be looped up
and securely fastened to the underside of the counter, or be
connected to an air gap.
■Use a drain air gap if the drain hose is connected to house
plumbing lower than 18" (45.7 cm) above the subfloor or floor.
Drain Air Gap
■Use ½" (1.3 cm) minimum I.D. drain line fittings.
NOTE: Do not connect drain lines from other devices to the
dishwasher drain hose.
INSTALLATION INSTRUCTIONS
1. Disconnect power.
2. Turn off water supply.
Prepare Cabinet Opening—
Existing Utility Hookups
Follow the steps in this section if you are installing the dishwasher
in an existing cabinet opening with utility hookups.
1. Check that the water supply line reaches to the front left-hand
side of the opening where the water connection will be made.
2. Check that the direct wire reaches to the front right-hand side
of the opening where the electrical connection will be made.
IMPORTANT: Always use a new drain hose even when installing
a new replacement dishwasher.
3. Drill a 1¹⁄₂" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
Connect Drain Hose to Air Gap—Waste Disposal
1. Remove the waste disposal knockout plug. Cut the end of the
drain hose, if needed.
NOTE: Do not cut the ribbed section.
2. Attach the drain hose to the air gap with the large spring-type
clamp.
NOTE: If the drain hose was cut, use 1¹⁄₂" to 2 " (3.8 to 5 cm)
screw-type clamp (not provided).
3. Use a rubber hose connector (not provided) with spring- or
screw-type clamps (not provided) to connect the air gap to the
waste disposal inlet above the drain trap and at least
20" (50.8 cm) above the floor.
A. Water supply line
B. Direct wire
WARNING
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
Electrical Shock Hazard
6" (15.2 cm)
AB
-

6
Connect Drain Hose to Air Gap—No Waste Disposal
1. Cut the end of the drain hose, if needed.
NOTE: Do not cut the ribbed section.
2. Attach the drain hose to the air gap with the large spring-type
clamp.
NOTE: If the drain hose was cut, use 1¹⁄₂" to 2 " (3.8 to 5 cm)
screw-type clamp (not provided).
3. Use a rubber hose connector (not provided) with spring- or
screw-type clamps (not provided) to connect the air gap to the
waste tee above the drain trap and at least 20" (50.8 cm)
above the floor.
Connect Drain Hose to Waste Disposal—No Air Gap
1. Remove the waste disposal knockout plug.
NOTE: Do not cut the end of the drain hose.
2. Attach the drain hose to the waste disposal inlet with the large
spring-type clamp.
This connection must be before the drain trap and at least
20" (50.8 cm) above the floor.
NOTE: It is recommended that the drain hose be looped up
and securely fastened to the underside of the counter.
Connect Drain Hose—No Waste Disposal or Air Gap
1. Cut the end of the drain hose, if needed.
NOTE: Do not cut the ribbed section.
2. Attach the drain hose to the waste tee with the 1¹⁄₂" to
2" (3.8 cm to 5 cm) screw-type clamp (not provided).
This connection must be before the drain trap and at least
20" (50.8 cm) above the floor.
NOTE: It is recommended that the drain hose be looped up
and securely fastened to the underside of the counter.
A. Drain hose—cut here, if needed
B. Spring- or screw-type clamps
C. Air gap
D. Large spring-type clamp
E. Drain hose
F. Rubber hose connector
G. Disposal inlet
H. Drain trap
A. Drain hose—cut here, if needed
B. Spring- or screw-type clamps
C. Air gap
D. Large spring-type clamp
E. Drain hose
F. Rubber hose connector
G. Waste tee
H. Drain trap
E
D
C
G
H
AB
F
E
D
C
G
H
A
B
F
A. Large spring-type clamp
B. Drain hose
C. Disposal inlet
D. Drain trap
B
A
C
D
A. Drain hose—cut here, if needed
B. Screw-type clamp
C. Drain hose
D. Drain trap
E. Waste tee
E
D
C
A
B

7
Prepare Cabinet Opening—No Existing
Utility Hookups
Install Electrical Connection—Direct Wire Method
1. Drill a ³⁄₄" (1.9 cm) hole in the right-hand cabinet side, the rear
or floor of opening.
2. If the cabinet is wood, sand hole until smooth. If the cabinet is
metal, cover the hole with a grommet (not provided).
3. Route cable from power supply through cabinet hole (cable
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
A. Optional locations
B. Preferred locations
■For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. The dishwasher is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and
ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
dishwasher is properly grounded. Do not modify the
plug provided with the dishwasher; if it will not fit the
outlet, have a proper outlet installed by a qualified
electrician.
■For a permanently connected dishwasher:
The dishwasher must be connected to a grounded
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the dishwasher.
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
B
A
must extend to the right front side of cabinet opening). Tape
cable to the floor 6" in front of unit. This will prohibit cable
from moving when dishwasher is moved into cabinet opening".
Install Electrical Connection—Power Supply Cord
Method
NOTE: A mating, 3 prong grounded outlet is required in a cabinet
next to the dishwasher opening.
1. Drill a ³⁄₄" (1.9 cm) hole in the right-hand cabinet side, the rear
or floor of opening.
2. If the cabinet is wood, sand hole until smooth. If the cabinet is
metal, cover the hole with a grommet (Part Number 302797)
included with power supply cord kit.
A. Optional locations
B. Preferred locations
B
A

8
Install Water Line
1. Drill a ¹⁄₂" (1.3 cm) hole in the left-hand cabinet side, the rear or
floor of opening.
2. Measure the overall length of the copper tubing required.
3. Attach the copper tubing to the water supply line with a
manual shutoff valve.
4. Slowly feed the copper tubing through the hole in the cabinet.
NOTE: The copper tubing will bend and kink easily.
The copper tubing should be far enough into the cabinet
opening to connect it to the dishwasher inlet on the front left-
hand side of the dishwasher.
5. Turn on the water shutoff valve. Run water into a shallow pan
to flush the copper tubing of particles that may clog the inlet
valve.
6. Turn off the shutoff valve.
Connect Drain Hose to Air Gap—Waste Disposal
IMPORTANT: Always use a new drain hose even when installing
a new replacement dishwasher.
1. Drill a 1¹⁄₂" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
2. Remove the waste disposal knockout plug. Cut the end of the
drain hose, if needed.
NOTE: Do not cut the ribbed section.
3. Attach the drain hose to the air gap with the large spring-type
clamp.
NOTE: If the drain hose was cut, use 1¹⁄₂" to 2 " (3.8 to 5 cm)
screw-type clamp (not provided).
4. Use a rubber hose connector (not provided) with spring- or
screw-type clamps (not provided) to connect the air gap to the
waste disposal inlet above the drain trap and at least
20" (50.8 cm) above the floor.
Connect Drain Hose to Air Gap—No Waste Disposal
IMPORTANT: Always use a new drain hose even when installing
a new replacement dishwasher.
1. Drill a 1¹⁄₂" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
2. Cut the end of the drain hose, if needed.
NOTE: Do not cut the ribbed section.
3. Attach the drain hose to the air gap with the large spring-type
clamp.
NOTE: If the drain hose was cut, use 1¹⁄₂" to 2 " (3.8 to 5 cm)
screw-type clamp (not provided).
A. Optional locations
B. Preferred locations
B
A
A. Drain hose—cut here, if needed
B. Spring- or screw-type clamps
C. Air gap
D. Large spring-type clamp
E. Drain hose
F. Rubber hose connector
G. Disposal inlet
H. Drain trap
E
D
C
G
H
AB
F
-
4. Use a rubber hose connector (not provided) with spring- or
screw-type clamps (not provided) to connect the air gap to the
waste tee above the drain trap and at least 20" (50.8 cm)
above the floor.

9
Connect Drain Hose to Waste Disposal—No Air Gap
IMPORTANT: Always use a new drain hose even when installing
a new replacement dishwasher.
1. Drill a 1¹⁄₂" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
2. Remove the waste disposal knockout plug.
NOTE: Do not cut the end of the drain hose.
3. Attach the drain hose to the waste disposal inlet with the large
spring-type clamp.
This connection must be before the drain trap and at least
20" (50.8 cm) above the floor.
NOTE: It is recommended that the drain hose be looped up
and securely fastened to the underside of the counter.
Connect Drain Hose—No Waste Disposal or Air Gap
IMPORTANT: Always use a new drain hose even when installing
a new replacement dishwasher.
1. Drill a 1¹⁄₂" (3.8 cm) diameter hole in the cabinet wall or floor on
the side of the opening closest to the sink.
2. Cut the end of the drain hose, if needed.
NOTE: Do not cut the ribbed section.
3. Attach the drain hose to the waste tee with the 1¹⁄₂" to
2" (3.8 cm to 5 cm) screw-type clamp (not provided).
This connection must be before the drain trap and at least
20" (50.8 cm) above the floor.
NOTE: It is recommended that the drain hose be looped up
and securely fastened to the underside of the counter.
A. Drain hose—cut here, if needed
B. Spring- or screw-type clamps
C. Air gap
D. Large spring-type clamp
E. Drain hose
F. Rubber hose connector
G. Waste tee
H. Drain trap
E
D
C
G
H
A
B
F
-
A. Large spring-type clamp
B. Drain hose
C. Disposal inlet
D. Drain trap
B
A
C
D
-
A. Drain hose—cut here, if needed
B. Screw-type clamp
C. Drain hose
D. Drain trap
E. Waste tee
E
D
C
A
B
Install Dishwasher
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.

10
Prepare Dishwasher for Installation
1. Using 2 or more people, place the dishwasher on its back on a
piece of cardboard.
2. Using a Phillips screwdriver, remove the 4 screws attaching
the toekick panel and lower panel to the dishwasher.
3. Remove both panels and set aside on a protected surface.
4. Apply thread seal tape to 90º elbow fitting and connect fitting
to water inlet valve.
5. Tighten elbow until snug.
NOTE: Elbow should face to the rear of the dishwasher.
terminal box cover.
■Direct Wire—Install a U.L. listed/CSA certified clamp
connector to the terminal box. If using conduit, use a U.L.
listed/CSA certified conduit connector.
■Power Supply Cord—Install a power supply cord kit that is
U.L. listed and marked for use with dishwashers (Part
Number 4317824).
7. Measure the shortest opening height between the underside
of the countertop and the floor where the dishwasher will be
installed.
8. Extend leveling legs out from the dishwasher base, ¹⁄₄" less
than the shortest opening height.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
A. Screws
A. Water inlet valve
B. Elbow
A. Leveling leg
A
A
B
A
6. Remove top screw and slide cover to the right to remove
Check Door Spring Tension
1. Using 2 or more people, place the dishwasher upright in front
of cabinet opening.
2. With one person holding the dishwasher to avoid tipping,
open and close the dishwasher door a few times. If the door
closes too quickly or falls open under its own weight, adjust
the tension.
■If the door closes too quickly, decrease the spring tension
by pulling the spring adjustment pin out of its hole and
reinsert it into the next lower hole toward the back of the
dishwasher.
■If the door falls open, increase the spring tension by
pulling the spring adjustment pin out of its hole and
reinserting it into the next higher hole toward the top
of the dishwasher.
NOTE: The spring adjustment pins should be in the same holes
on both the left-hand and right-hand sides of the dishwasher.
Move Dishwasher into Cabinet Opening
1. Using 2 or more people, grasp the sides of the dishwasher at
the edges of the door panel and move dishwasher close to the
cabinet opening.
NOTE: Do not push on the front of the panel or on the console
to avoid bending or denting them.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
ARNING
W
■Do not remove the tie wrap in the top holes. The top
two holes should not be used.

11
2. If direct wired, check that the power supply wire is on the
right-hand side at the front of the cabinet opening.
If using a power supply cord, insert the power supply cord
through the hole cut in the cabinet wall.
3. Check that the water supply line is on the left-hand side of the
cabinet opening.
4. Check that the drain hose is near the center and insert the drain
hose through the hole in the cabinet .
5. Slowly move the dishwasher into place inside the cabinet
opening with the front corners of the dishwasher door flush
with the cabinet doors.
NOTES:
■Do not kink or pinch the copper tubing, drain hose, power
supply cord or the direct wire between the dishwasher and
the cabinet.
■Do not remove the insulation blanket from dishwasher to
allow the dishwasher to fit easier into the cabinet opening.
The insulation blanket reduces the sound level when the
dishwasher is operating.
6. If needed, support the front of the dishwasher by raising,
lowering or shimming the front legs.
7. Remove cardboard from beneath the dishwasher.
Level the Dishwasher
1. Align the front of the dishwasher door panel with the cabinet
doors by adjusting the front legs using the 6" adjustable
wrench.
2. Check that the leveling legs are firmly against the floor.
3. Close and latch the dishwasher door.
4. Place a level against the front panel above the leg to check
that the dishwasher is plumb. If needed, adjust the leveling leg
or add shims until the dishwasher is plumb.
NOTE: Shims must be securely attached to the floor to avoid
their movement during dishwasher operation.
5. Repeat for the other side of the dishwasher.
6. Place the level against the top front opening of the tub. Check
that the dishwasher is level from side to side. If the
dishwasher is not level, adjust the front legs up or down until
the dishwasher is level.
Make Electrical Connections—
Direct Wire Method
Review “Electrical Requirements” before continuing.
1. Route the direct wire so that it does not touch the dishwasher
motor or lower part of the dishwasher tub.
2. Pull cable through UL listed / CSA approved strain relief in
3. Using twist-on connectors sized to connect direct wire to
16-gauge dishwasher wire, connect the white wire from the
power supply to the white wire on the terminal box.
4. Using twist-on connectors sized to connect direct wire to
16-gauge dishwasher wire, connect the black wire from the
power supply to the black wire on the terminal box.
5. Using twist-on connectors sized to connect direct wire to
16-gauge dishwasher wire, connect the ground wires from the
power supply to the green ground dishwasher wire.
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
erminal box. Strain relief is not provided with dishwasher.
Owner must purchase a 7/8" screw-in type strain relief.

Use UL listed power supply cord kit (part number 4317824).
54" (137.2 cm) minimum and 64" (162.6 cm) maximum.
12
6. Tighten the clamp connector or conduit connector screws.
7. Reinstall the terminal box cover with the wires inside terminal
box.
8. Check that no wires are pinched by the cover.
Make Electrical Connections—Power
Supply Cord Method
The power supply cored and connections must comply with the
National Electrical Code, Section 422 and/or local codes and
ordinances. Recommended power supply cord length is
1. Remove the terminal box cover.
2. Using twist-on connectors sized to connect direct wire to
16-gauge dishwasher wire, connect the white wire from the
power supply cord to the white wire on the terminal box.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
A. White wire to white wire
B.Ground wires to green ground connector
C. Grounding screw
D. Black wire to black wire
3. Using twist-on connectors sized to connect direct wire to
16-gauge dishwasher wire, connect the black wire from the
power supply cord to the black wire on the terminal box.
4. Using twist-on connectors sized to connect direct wire to
16-gauge dishwasher wire, connect the ground wire from the
power supply cord to the green ground dishwasher wire.
5. Reinstall the terminal box cover with the wires inside terminal
box.
6. Check that no wires are pinched by the cover.
7. Plug power supply cord into a grounded 3 prong outlet.
8. Check that the power supply cord does not touch the
dishwasher motor or lower part of dishwasher tub.
Connect Dishwasher to Water Supply
1. Route the water supply line so that it does not touch the
dishwasher base, frame or motor.
2. Slide the nut onto the copper tubing about 1" (2.5 cm).
3. Slide the ferrule onto the tubing.
NOTE: Do not position ferrule on the end of the tubing.
4. Push the tubing into the elbow as far as it will go.
5. Slide the nut and ferrule forward and start the nut onto the
elbow threads. Avoid bending or kinking the copper tubing.
6. With the copper tubing pushed into the compression fitting as
far as it will go, use a wrench and tighten the compression
fitting nut to elbow on water inlet valve.
NOTE: Do not use Teflon® tape with compression fittings.
A. Elbow
B. Ferrule
C. Nut
A
B
C
®Teflon is a registered trademark of E.I. Dupont de Nemours and
Company.
black
white
ground
Terminal box wire:
white
black
ground wire
Power supply wire:
white
black
ground wire
terminal
box cover
7. With flexible braided connections, secure nut to elbow using
5/8" open ended wrench or adjustable wrench.
black
white
ground
A.
B.
D.
C

13
8. Place paper towel under the elbow.
9. Turn on the water supply.
10. Check for leaks.
Connect Dishwasher to Drain
11. Route the drain hose so that it does not touch the dishwasher
motor, door springs, water line, cabinet, flooring or the edge of
the hole where it passes through the cabinet.
NOTE: Do not remove the drain loop from the side of the
dishwasher.
12. Place the shallow pan under the end of the drain hose. The
pan will collect any water in the drain hose.
13. Cut on the molded end of the drain hose to fit 1" (2.5 cm),
³⁄₄" (1.9 cm) or ⁵⁄₈" (1.6 cm) diameter connections on the air
gap, waste tee or waste disposal.
14. If a longer drain hose is required, add up to 42" (107 cm) of
length for a total of 10 ft (3 m) to the factory-installed drain
hose.
NOTE: Total drain hose length must not exceed 10 ft (3 m) for
proper drain operation.
15. Using ⁵⁄₈" or ⁷⁄₈" I.D. hose and a coupler, connect the two drain
hose ends with hose clamps.
16. Connect the drain hose to the air gap, waste tee or disposal
with clamps.
A. Water inlet valve
B. Elbow
A. Drain hose
A. Cutting lines
A. Hose clamps
B. Coupler
A
B
A
1" 3/4" 5/8"
A
A
A
B
The dishwasher must be secured to wood countertop.
Method 1
Attach Dishwasher to Cabinet
17. Open the dishwasher door and remove the lower dish rack.
18. Place a towel over the pump assembly and spray arm of
dishwasher to keep screws from falling into pump area during
installation.
19. Check that the dishwasher is level and centered side to side in
the opening.
20. Check that the tub flange aligns with the front face of the
cabinet frame.
21. Attach the dishwasher to the countertop using the 2 brackets
on top of the dishwasher.
NOTE: The dishwasher must be attached to the countertop to
keep it from tipping when the door is opened.
22. Insert 2 #8 x ⁵⁄₈" Phillips flat-head screws through the brackets
and into the countertop.
23. Open the door about 3" (7.6 cm) and check that the space
between the inner door and tub is equal on both sides.
24. If spacing is not equal, loosen the bracket screws and shift the
tub. Retighten bracket screws.
25. Check that the top of the door does not contact the screws,
brackets or countertop. If it does, the dishwasher must be
lowered and leveled again. See “Level Dishwasher” in “Install
Dishwasher.”
A. Brackets
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
A
Wood countertop

27.
mounting brackets.
will not accept screws,secure dishwasher with side-
When countertops are granite or other materials that
``Method 2
14
remove plug buttons (one on each side).
Install screws through the dishwasher sidemount bracket
and into the adjacent cabinet on each side. Reinstall plug
buttons.
When step is complete, close dishwasher door and verify that
gap between countertop and top of dishwasher door is at
least 1/2".
Countertop
Screws
Plug Buttons
Granite Countertop
½'’
min. Dishwasher Door
26. Use a flat-blade screwdriver or prying tool to
Complete Installation
28. Place the lower panel behind the toekick panel.
29. Place the 2 panels against the legs of the dishwasher.
30. Align the slots on the inner panel with the toekick bracket
screw holes. The lower panel should be touching the floor.
31. Insert the 4 toekick screws into the 4 screw holes.
A. Top 4 screw holes
B. 2-piece toekick
A
B
Direct Wire Method
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power Supply Cord Method
32. Reconnect power or plug in dishwasher.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
WARNING
Check Dishwasher Operation
1. Read the User Instructions that came with your dishwasher.
2. Check that all parts have been installed and no steps were
skipped.
3. Check that you have all the tools you used.
4. Start the dishwasher and allow it to complete the shortest
wash cycle.
5. After 2 minutes, unlatch the door. Wait 5 seconds, and then
open the door.
6. Check to see that there is water in the bottom of the
dishwasher tub.
7. Check that the dishwasher is working properly.
If you need Assistance or Service
Please reference the “Assistance or Service” section of your User
Instructions or contact the dealer from whom you purchased your
dishwasher.

Notes
15

SÉCURITÉ DU LAVE-VAISSELLE
Votre sécurité et celle des autres est très importante.
Dans ce manuel et survotre appareil, nous fournissons de nombreux messages importants desécurité. Lisez et respectez toujours
tous les messagesde sécurité.
Ceci est le symbole d'alerte de sécurité.
Cesymbole meten garde contre les risquespotentiels qui peuvent vous tuer ou vous blesser,vous ou d'autres
personnes.
Tous les messages de sécurité suivent lesymbole d'alerte de sécurité ou le mot « DANGER» ou
«AVERTISSEMENT». Cesmotssignifient:
DANGER
AVERTISSEMENT
Vous pourriezêtre tué ougravement blessé si vousne respectez
pas immédiatement les consignes.
Vous pourriezêtre tué ougravement blessé si vousne respectez
pas lesconsignes.
Tous les messages de sécuritéindiquent le risque potentiel, vous disent comment réduire la probabilité de blessure et ce quipeut
arriver si lesconsignes ne sont pas respectées.
AVERTISSEMENT
Risque de basculement
N'utilisez pas le lave-vaisselle tant qu'il n'est pas complètement installé.
N'appuyezpassurlaporte ouverte.
Celapourrait entraîner desblessures graves ou des coupures.
Vous devez :
Ouvrir doucementla porte dulave-vaissellependant que
quelqu'un saisitl'arrièredu lave-vaisselle.Retirerlesmatériaux
d'expédition. Fermer la porte du lave-vaisselle. Verrouiller la
porte du lave-vaisselle.
Respecter tous les codes et règlements en vigueur.
Installer ce lave-vaisselle conformément à cesconsignes.
Disposer de tout cedont vous avez besoin pour installer
correctementlelave-vaisselle.
Contacter un installateur qualifié pour vous assurer que le
lave-vaissellesoitinstalléconformémentà touslescodes
et règlementsnationaux et locaux en matière d'électricité
et de plomberie.
CONFIGURATION REQUISE POUR L'INSTALLATION
Outils et pièces
Rassemblez les pièces et outils requis avant de commencer
l'installation. Lisez et respectez les consignes fournies avec
tout outil indiquéici.
Outils nécessaires
Pièces nécessaires
Coude à 90° avec filetages
externes N.P.T de ³/8 po à
une extrémité
Collier deserrage à vis de 1¹/2
poà2po(3,8cmà5,1cm)
Connecteur de collier (serre-câble)
Tournevis Phillips
Tournevis à lame plate
Ruban ou règle à mesurer
Forets de scie àtrous de ¹/2
po,³/4poet1½po(1,3mm,
1,9 mm et 3,8 cm)
Assiettepeuprofonde
Clé réglable de 6 po (15,2cm)
Petit coupe-tube
Niveau
Perceusesansfil
Mèche de ¹/8 po
Lampe torche
REMARQUE : L'autre extrémité
doit correspondre à la conduite
d'alimentationeneau.
Ruban d'étanchéité pour filetage
3écrousde câble homologuésUL
Collier de serrage à vis de 1¹/2
poà2po(3,8cmà5,1cm)en
cas de raccordement au téde
vidage
Tube encuivre
(³/8po recommandé)
pour correspondre autrou de
diamètre 7/8 po (22,2 cm)
16

Pièces fournies
Vérifiez que toutes les pièces sont incluses. Reportez-vous à
la liste séparéedes pièces pour les accessoires disponibles
pour votre lave-vaisselle.
Dimensions du produit
Vue latérale
A.VisàboisàtêteplatePhillipsn°8x5/8po
B.Vis de plinthePhillips, àempreinte cruciforme,
de couleurassortie, de 24 po (61 cm)*
Configuration requise pour l'emplacement
IMPORTANT :Respectez tous les codes et règlements envigueur.
Le non-respectdes codes et des règlements peut engendrerun
incendie ou un choc électrique.
Il estde votre responsabilité d'effectuer une installation appropriée.
Contactez un installateur qualifié pour vous assurer que le lave-
vaisselle soitinstallé conformément àtous les codes et règlements
nationaux etlocauxen matièred'électricitéetde plomberie.
Installez le lave-vaisselle conformément à ces consignes.
Disposez de tout ce dont vous avez besoin pour installer
correctement le lave-vaisselle.
Protégez le lave-vaisselle et lesconduites d'eau allant au lave-
vaissellecontre legel. Les dégâtscausés par le gel ne sont pas
couverts parla garantie.
Celave-vaisselle est fabriqué pour unusageintérieur uniquement.
16-5/8 po (42,2 cm) 2 ¹/2 po (6,2 cm)
Installez et mettez àniveau le lave-vaissellesur un plancher qui
en supporterale poids,dansunespace convenablepourses
dimensions et son utilisation.
Installez le lave-vaisselle dans un emplacement disposant d'un
accès facile à l'eau, à l'électricité et à la vidange.
Complètement étanche des deux côtés, à l'arrière et au sommet.
23-5/9 po (59,8 cm)
Dégagements minimaux
REMARQUES :
Les emplacements en coin nécessitent un dégagement minimal
de2po(5,1cm)entrelecôtédelaportedulave-vaisselleetlae
mur ou l'armoire.
Un minimumde 255/8 po (65,1 cm) est requis à l'avant du lave-
vaisselle pour permettre l'ouverture complète de la porte.
L'ouverture doit être carrée et leplancher doit êtreà niveau.
A. Un dégagement de 2 po (5,1 cm) minimum
pour l'ouverturede laporte.
B. Lave-vaisselle
C.Comptoir
D. 255/8 po (65,1 cm) minimum
Vue arrière
* À l'avant du cadre de la porte
32¹/2 po à 34¹/2 po
(82,6 à 87,6cm)
24 po (61 cm) maximum
17

Dégagements d'installation
Dimensions de découpe
24 po (61 cm)
maximum
24 po (61cm)
maximum
34poà35po
(86,4cmà 88,9cm)
6po
(15,2 cm)
CONSIGNESDE MISE À LA TERRE
Pour un lave-vaisselle mis à laterre et connecté par cordon :
Le lave-vaisselle doit être misà la terre. Encasde
dysfonctionnement ou dedéfaillance, lamise à laterre
réduitlerisque dechocélectriqueenfournissantune voie
de moindrerésistanceaucourant électrique. Lelave-
vaisselle estéquipé d'uncordon disposant d'un conducteur
de mise à laterre et d'une fiche de mise à laterre.La fiche
doit être branchée dans une prise appropriée installée et
mise à la terre conformément à tous les codes et
règlements locaux.
AVERTISSEMENT: Un défautde raccordement du
conducteurde mise àlaterre peutentraîner unrisque de
choc électrique. En cas de doute, faites vérifier la mise à
la terre dulave-vaissellepar unélectricien agréé ou un
représentant duServiceAprès-VenteNe modifiez pasla
fiche fournieavecle lave-vaisselle;si elle ne correspond
pas à la prise, faites installer une prise adéquate par un
électricien qualifié.
Pour un lave-vaisselle branché en permanence :
A.Toutes lessurfaces doivent être
dépourvues d'intrusions
* Dessous du comptoir au plancher
REMARQUES:
Percez destrous dans la zone ombrée des parois de l'armoire ou
dans leplancher pour les travaux de plomberie etd'électricité.
L'installationADA, 32-1/2 po (82,5 cm)sousles comptoirs élevés
de 34 po (86,4 cm) peut être réaliséeen ajustant laplinthe et les
piedsde mise à niveau.
AVERTISSEMENT
Risque de choc électrique
Configuration requise pour l'électricité
Branchez dans unepriseà3 broches mise àla terre. Ne retirez
pas labroche de terre.
N'utilisez pas un adaptateur.
N'utilisez pas unerallongeélectrique.
Le non-respect deces consignes peut entraîner la mort, un
incendie ouun choc électrique.
CONSERVEZ CES INSTRUCTIONS
Contactez un électricienqualifié.
Assurez-vous que l'installation électrique soit adéquate et en
conformitéavec tous les codes et règlements nationaux et locaux.
Configuration requise :
Alimentationélectriquede120volts,60Hz,courantalternatif
uniquement, 15 ou 20 ampères,protégée parfusible.
Câble en cuivre uniquement, 2 câbles avec mise à la terre
Recommandé :
Fusibletemporisé ou disjoncteur
Circuit séparé
Branchement par câblage direct
Utilisez un câble flexible, blindé ou à blindage non métallique, en
cuivre avec un filde mise àla terre conformeaux exigences de
câblage de votre maison etaux codes et règlements locaux.
Branchement par cordon d'alimentation
Utilisez la trousse de cordon d'alimentation(pièce numéro 4317824)
destinée aux lave-vaisselle. La trousse comprend :
Cordon d'alimentation à 3 câbles et 16 jauges, homologué UL,
avecfichedemiseàlaterreà3broches
Serre-câbleNeerC-500de 7/8po
3 connecteurs de câble
Oeillet, piècenuméro 302797
Respectez les consignes de la trousse pour l'installation du cordon
d'alimentation.Le cordon d'alimentation doit êtrebranché dans une
prise à troisbroches, mise àla terre,situéedansl'armoire à côté de
l'ouverturedu lave-vaisselle. La prise doit respecter tous les codes
etrèglementslocaux.
Sivousprévoyez d'installerunbroyeur de déchets,
une alimentationélectrique supplémentaire distincte de120volts,
60 Hz, courant alternatif uniquement, 15 ou20 ampères, protégée
par fusible, est requise.
REMARQUE :
IMPORTANT :
Le lave-vaisselle doit être raccordé à un système métallique
mis àla terre de câblage permanent,ou un conducteur de
mise àla terre doit être utilisé avec les conducteurs du
circuitet raccordéà la borne demiseà la terre ou acheminé
au lave-vaisselle.
18

Configuration requise pour l'alimentation en eau
Uneconduited'eauchaude avec unepression d'eau de 20-120
psi (138-862 kPa).
Température d'eau du lave-vaisselle à120°F (49°C).
Tube en cuivre de diamètre extérieur³/8 poavec raccordde
compressionouconduited'alimentationeneautresséeflexible.
Tubeen plastique de ½po minimum non
recommandé.
Coudeà 90°avecfiletages externes N.P.T de ³/8 po à une extrémité.
Ne soudez pas àmoins de 6 po (15,2 cm)de la valve
d'arrivée d'eau.
REMARQUE :
IMPORTANT :
Raccordez le tuyau devidange au té de vidageouà l'entrée du
broyeurde déchets au-dessus dusiphon dans la plomberie de
l'habitation.
Raccordez letuyau devidange à la plomberiede l'habitation à
20 po (50,8 cm) minimum au-dessus du plancher.
REMARQUE : Il est recommandé que le tuyau devidange, soit forme
une boucleet soit solidementfixé sous le compteur,ou qu'il soit
raccordé àune coupureanti-retour.
Utilisez une coupure anti-retour de vidange si le tuyau de vidange
est raccordé uneplomberie d'habitation inférieure à 18po
(45,7 cm) au-dessus dusous-plancherou du plancher.
Coupure anti-retour de vidange
Configuration requise pour la vidange
Utilisez le nouveau tuyau de vidange fourni avec votre lave-vaisselle.
REMARQUE : Siun tuyau de vidangeplus long est requis :
Utilisez un nouveau tuyau de vidange d'une longueur maximale
de 10 pieds (3 m), conforme à toutes les normesactuelles de test
AHAM/IAPMO.
Utilisez un nouveau tuyau de vidange résistant à la chaleur et aux
détergents.
Utilisez un nouveau tuyau de vidange qui correspond au
connecteur de vidange de 1 po(2,5 cm) du lave-vaisselle.
Utilisezdesraccords de conduitede vidangedediamètre
intérieur égal à ½ po (1,3 cm) minimum.
REMARQUE : Ne raccordez pasles conduites devidange
provenant d'autres dispositifs au tuyau de vidange du lave-vaisselle.
NOTICE D'INSTALLATION
3.Percez untrou de diamètre 1¹/2 po (3,8 cm) dans la paroi de
l'armoire ousur leplancher du côté del'ouverture la plus proche de
l'évier.
Risque de choc électrique
Débranchez l'alimentation électrique de la boîte de fusibles
ou du disjoncteur avant d'installer le lave-vaisselle.
Le nonrespect de cette consigne peut entraîner lamort ou un
chocélectrique.
1.Débranchezl'alimentation électrique.
2.Coupez l'alimentation en eau.
Préparer l'ouverture de l'armoire -
Raccords de serviceexistants
Suivez les étapes de cette sectionsivousinstallez le lave-vaisselledans
une ouverture existante de l'armoire à l'aide des raccords deservice.
1.Vérifiezque la conduite d'alimentation eneau atteignele côté
avant gauche del'ouverture où s'effectue le raccordement d'eau.
2.Vérifiezque le câblage direct atteigne le côté avant droite de
l'ouvertureoù s'effectue le raccordementélectrique.
Raccorder le tuyau de vidange àla coupure anti-retour-
Dispositif d'élimination des déchets
1.Retirezle bouchon d'alvéole défonçable du dispositif d'élimination
desdéchets. Coupez l'extrémité du tuyau de vidange, si nécessaire.
Ne coupez pas la section ondulée.
2.Fixez le tuyau de vidange à lacoupure anti-retour à l'aide d'un grand
collierdeserrage à ressort.
Si le tuyau de vidange a étécoupé, utilisez le collier de
serrageàvisde1¹/2poà2po(3,8à5cm)(nonfourni).
3.Utilisez un connecteurde tuyau en caoutchouc (non fourni) avec des
colliers de serrage à ressort ou à vis (non fournis) pour raccorder la
coupureanti-retour à l'entréedu dispositifd'éliminationde déchets
au-dessusdusiphonàaumoins20po(50,8cm)au-dessusdu
plancher.
REMARQUE :
REMARQUE :
6po(15,2cm)
A. Conduite d'alimentation en eau
B.Câblagedirect
IMPORTANT : Utilisez toujoursun nouveau tuyaude vidange même
lors del'installationd'unnouveau lave-vaissellede remplacement.
AVERTISSEMENT
19

REMARQUE : Il est recommandé quele tuyau devidange forme
une boucleet soit solidementfixé sous le compteur.
A. Tuyau de vidange - coupez ici si nécessaire
B. Colliersde serrage àressort ou à vis
C. Coupure anti-retour
D. Grand collier de serrage à ressort
E. Tuyau de vidange
F. Connecteur de tuyau en caoutchouc
G. Entrée du dispositif d'élimination de déchets
H.Siphon
A. Grandcollier deserrage àressort
B.Tuyaudevidange
C. Entrée du dispositif d'élimination de déchets
D.Siphon
Raccorder le tuyau de vidange à la coupure anti-retour -
Pas de dispositif d'élimination des déchets
1.Coupezl'extrémité du tuyau de vidange, si nécessaire.
Ne coupez pas la section ondulée.
2.Fixez letuyaude vidangeà la coupureanti-retour àl'aided'un
grand collier deserrage à ressort.
Si le tuyau de vidange a été coupé, utilisezun
collierde serrage à vis de1¹/2 po à 2 po(3,8 à5 cm) (nonfourni).
3.Utilisez un connecteur de tuyauen caoutchouc (non fourni) avec
des colliers de serrage à ressort ouà vis (non fournis) pour
raccorder la coupure anti-retour auté de vidage au-dessus du
siphon et à aumoins20 po (50,8 cm) au-dessusduplancher.
REMARQUE :
REMARQUE :
Raccorder le tuyau devidange - Pas de
dispositifd'élimination des déchets
1.Coupez l'extrémité du tuyau de vidange, si nécessaire.
Necoupez paslasection ondulée.
2.Fixezletuyaudevidangeautédevidageàl'aided'uncollierde
serrageàvisde1¹/2poà2po(3,8cmà5cm)(nonfourni).
Ceraccordement doit s'effectueren amont dusiphon et à au moins
20po (50,8 cm)au-dessus du plancher.
Ilest recommandé que le tuyau de vidange forme une
boucle etsoit solidementfixésous le compteur.
REMARQUE :
REMARQUE :
A. Tuyau de vidange -
coupez ici si nécessaire
B. Colliersde serrage à ressort ou à vis
C.Coupureanti-retour
D.Grandcollierdeserrageàressort
E. Tuyau de vidange
F. Connecteur de tuyau en caoutchouc
G.Té devidage
H. Siphon
A. Tuyau de vidange - coupez ici si nécessaire
B.Collierde serrage à vis
C.Tuyaude vidange
D.Siphon
E. Té de vidage
Raccorderle tuyau de vidange au dispositif d'élimination
des déchets - Pasde coupureanti-retour
1.Retirez le bouchon d'alvéole défonçable du dispositif d'élimination
des déchets. Ne coupez pas l'extrémité du tuyau de vidange.
2.Fixez letuyaude vidangeà l'entrée dudispositif d'élimination des
déchetsàl'aided'ungrandcollierde serrageà ressort.
Ce raccordement doit s'effectueren amont dusiphon et àau moins
20po (50,8 cm) au-dessus du plancher.
REMARQUE :
20