Whirlpool LE5800XS User manual

AUTOMATIC
DRYERS
Electric Model
LE5800XS
and
Gas Model
LG5801XS
~lCrOWave Ovens Trash Compactors Room Air Condltloners Dehumldffiers Automallc Washers Clo!hes Dryers Freezers Aefrlgerator~F

Parts and features
CYCLE CONTROL KNOB
I LAUNDRY INFORMATION CENTER
TEMPERATURESELECTOR 4
Remove the Con-
sumer Buy Guide label
before using your
dryer. It will be easier
to remove.
Copy your Model and Serial Numbers here
When you need service or call with a
question, have this information ready:
1. Complete Model and Serial Numbers Model Number
(from plate located as shown).
2. Purchase date from sales slip. Serial Number
Copy this information in these spaces.
Keep this book in the Laundry Information Purchase Date
Center with your “Dryer Guide” and sales
slip.
Thank you for purchasing a Whirlpool Service ComPanY Phone Number
product. Please complete and mail the Owner Registration Card tur-
nished with this product.
Contents
PARTS AND FEATURES
IMPORTANT SAFETY
INSTRUCTIONS
OPERATING INSTRUCTIONS..
Selecting a Cycle and
Starting Your Dryer
Automatic Cycles
Timed Drying
DRYING TIPS
FLUFFAIR Setting
TUMBLE PRESS” Setting
FINISH GUARD” Setting
Automatic DRY-MISER w
Control
Page
2
3
4
4
6
6
7
7
7
7
7
Gentle Heat.
Drying Times
Mixed Loads
End-of-Cycle Signal
Lint Signal
LINT SCREEN
LINT REMOVAL
CARING FOR YOUR DRYER.,
Cleaning Dryer Interior.
Vacatron Care
IF YOU NEED SERVICE OR
ASSISTANCE
WHIRLPOOL DRYER
WARRANTY
Page
7
11
12
2 c1987 Whirlpool Corporation

Additional Safety Instructions and Your Responsibilities
NEVER operate the dryer if.
l it is not working right (1.e norsy, too hot)
9 it is damaged.
l parts are missing (1.e door latch)
l all panels are not in place.
l the lint screen IS loose, damaged or
missrng.
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical
switches.
3. ;l;treguish any open
.
4. Immediately call your
gas supplier.
FOR YOUR SAFETY
Do not store or use gas-
oline or other flammable
vapors and liquids in the
vicinity of this or any other
appliance.
ALWAYS shut off the gas valve before leov-
rng on vacatton.
ALWAYS unplug the power supply cord or
turn off electrical power before attempting
to service the dryer. Shut off GAS VALVE il
yours IS a gas dryer.
You are personally responsible for making
sure that your dryer...
l is properly maintained.
l IS properly installed and leveled rn a well
ventilated room* on a floor that can sup-
port the weight
l IS located in an area where the tempera-
ture is above 4.5 F (7.2 C).
l is connected to the proper outlet and
electrical supply.’
l is properly connected to fuel and ex-
haust systems l
l IS not Installed against drapes or
curtains.”
l IS used only for jobs normally expected
of home clothes dryers.
l IS not used by children or anyone unable
to operate it properly.
*See “Installation Instructions” for com-
plete information.
3

SUGGESTED SUGGESTED
TYPE OF LOAD CYCLE TEMPERATURE
COTTONS - LINENS
EXTRA HEAVY - Bedspreads,
mattress pads, quilts HEAVY
HEAVYWEIGHT FABRICS-Towels, HIGH
jeans, corduroys, work clothes
MEDIUMWEIGHT COTTONS -
Sheets. Dillowcases, cotton
AUTOMATIC PERM’T PRESS
REGULAR MED
under\h;ear,diapers
LIGHTWEIGHT COTTONS - Batistes,
organdies, lingerie
PERMANENT PRESS, SYNTHETICS
AND BLENDS
KNITS GENTLE
LOW
HEAVYWEIGHT FABRICS-Work clothes,
jackets, raincoats
MEDIUMWEIGHT FABRICS - Shirts, play
clothes, sheets, slacks,,
LIGHTWEIGHT FABRICS - Lingerie,
blouses, dresses
AUTOMATIC PERMIT PRESS
PERMANENT MED
PRESS MED LOW
KNITS
HEAVYWEIGHT - Cottons, rayons,
blends,T-shirts, slacks, shirts
LIGHTWEIGHT - Synthetics (polyester,
acrylic, etc.) and blends, lingerie,
blouses, dresses
LIGHTWEIGHT AND DELICATE FABRICS
Sheer Curtains (2 or 3 panels]
Gauze, lace, etc.
RUBBER, PLASTIC, HEAT-SENSITIVE
FABRICS
FOAM RUBBER- Pillows, bras,
AUTOMATIC MED LOW
PERMANENT
PRESS KNITS GENTLE
LOW
AUTOMATIC
PERMANENT Ex LOW
PRESS
stuffedtoys ._..,....,,,,..,,...,......
PLASTIC - Shower curtains,
tablecloths............................
RUBBER-BACKED RUGS
OLEFIN, POLYPROPYLENE, SHEERNYLON
FLUFF Ex LOW
AIR
4

1
. Select a CYCLE 2
Set
. TEMPERATURE SELECTOR
Turn the Control Knob either way to
point to the cycle and setting you
want. See page 6 for information on
the cycles.
3
, Push the START Button
The dryer will start tumbling when you
push the STARTButton.
Ifthe STARTButton is pushed when the
Cycle Control Knob is pointing to an
OFF area, the End-of-Cycle Signal will
sound. Dryer will not start.
The Temperature Selector can be set
on any desired temperature or any-
where between 2 temperatures.
To stop and restart
the dryer
To stop the dryer, open the door (or
turn the Control Knob to OFF).
To restart the dryer, close the door,
select cycle, if necessary, and push
START.
The Cycle Control Knob should point to OFF when the dryer is not in use.
If the dryer is stopped before the cycle is finished, turn the Cycle Control
Knob to OFF. 5

The automatic cycles
The automatic cycles allow you to se-
lect the degree of dryness you prefer
for the clothes being dried.
The Control Knob will not move until
the clothes load is almost dry, or the
COOL.-DOWN portion of the cycle has
been reached. After COOL-DOWN, the
knob automatically moves to an OFF
area land tumbling stops.
weight cotton items. The load tumbles
without heat during the last 5 min-
utes. This helps make the load easier
to handle.
press, Knits and other synth’etic fab-
rics. The load tumbles without heat
during the last 10 minutes. This helps
keep wrinkles from setting in, and
makes the load easier to handle.
For the first few loads, set the Control
Knob to point to an $+ in either auto-
matic cycle. When the dryer stops, feel
the dried items.
l If items are drier than you like, use
a setting to the right of the Jk the next
time you dry a similar load.
l If items are not as dry as you like, use
a setting to the left of the +$ the next
time You dry a similar load.
Timed drying
Use the TIMED DRYING Cycle for
any load you want to dry by time. For
example: small loads, large bulky
items, items to be fluffed or dusted
with the FLUFFAIR heat setting.
l Turn the Control Knob to the number
of minutes you want-from 10 to 70.
l The last 5 minutes of this cycle are
without heat - a cool-down time. This
helps’ make the load easier to
handle.
6

Drying tips
The dryer does not heat when the
Control Knob is set on FLUFFAIR. This
setting can be used to fluff bedding,
plastic tablecloths, foam rubber
pillows, stuffed toys, sneakers, etc.
1. Turn the Control Knob to the number
of minutes you want in FLUFFAIR.
2. Push the STARTButton.
FINISH GUARD’ Setting
When you are unable to unload
the dryer as soon as it stops, wrinkles
can form.
If you don’t open the door within 5
minutes after the dryer stops, FINISH
GUARD takes over automatically to
protect the load. You don’t have to set
the Control Knob for FINISH GUARD.
FINISH GUARD tumbles the load,
without heat, every 5 minutes for up to
40 minutes. This tumbling rearranges
and fluffs the load to help avoid the
wrinkles that set in when the load
remains in the drum.
TUMBLE PRESS”’ Setting I
The TUMBLE PRESSsetting removes
wrinkles from dry clothing such as
items that may have been packed
in a suitcase, closet, or items not I
2. Set Temperature Selector to PERM’T
PRESS/MED.
3. Push STARTButton
The load will tumble in heated air
for15 minutes. The heat shuts off and
the dryer continues to tumble the load
for 5 more minutes.
For best results, TUMBLE PRESSonly
a few items at a time. Put them on
hangers or fold them as soon as the
dryer stops.
Automatic DRY-MISER”’
Control
-The thermostat senses the air
temperature. The dryer automatically
shuts off when the selected dryness
is reached.
Gentle Heat
The dryer automatically reduces
the heat settings in HEAVY HIGH and
PERMIT PRESSMED cycles. During
the last few minutes of each of
these cycles the dryer temperature
gradually reduces to a lower heat
setting. This helps prevent
overdrying. 7

Drying times Mixed loads
Drying times will vary depending on:
l amount of moisture in the clothes.
l type and weight of the fabric.
l size of the load.
. room temperature around the dryer.
l temperature of the wash rinse water.
l amount of lint in the lint screen.
l dryer temperature selection.
See your “Dryer Guide” for
more information.
End-of-cycle signal
When drying a load with different
kinds and weights of fabrics, use the
cycle suggested for the lightest fab-
rics. When the dryer stops, remove dry
items and reset the control.
To reduce wrinkling, take the load
from dryer as soon as tumbling stops.
This is important for permanent press,
knits and synthetic fabrics.
The dryer sounds a signal to let you know when
the cycle is finished. The signal cannot be turned
off and is not adjustable.
The signal is helpful when you are drying per-
manent press, synthetics and other items that
should be taken out as soon as the dryer stops.
dd
-
g@i!m&
Lint signal
Clean lint screen before each load. If you
neglect to clean your lint screen, the signal will
sound. The (whistle tone] signal lets you know
the air flow is being restricted. Restricted air flow
reduces drying efficiency.
Turn off the dryer and clean the lint screen as
shown on page 9.
8

Lint screen
Clean the lint screen before each load. A screen blocked by lint can
increase drying time and may be a FIREHAZARD.
Open the lid and pull the lint screen
straight out. ROLL the lint off the screen with
your fingers.
DO NOT rinse or wash the screen.
Push the screen firmly back into place
Lint removal
Lint can gather inside the dryer and create a FIRE HAZARD. This lint should
be removed at least every 2 to 3 years, or more often, depending on
dryer usage.
ELECTRIC DRYERS GAS DRYERS
Cleaning should be done only by a qualified person.
1. Remove back panel (electric)
or lower access panel (gas).
2. Avoid damaging wires,
thermostats, funnel or igniter.
3. Remove lint from shaded area -
see art - with a soft brush or
vacuum cleaner.
4. Replace panel; reconnect and
re-level dryer. 9

Caring for your dryer
Remove loose and sharp objects
from pockets and cuffs before drying -
pins, buckles, etc. Close metal
zippers.
Wipe off all spills with a damp, soft
cloth. Spills allowed to remain may
dull or damage the finish.
Never leave wet or damp laundry
in your dryer.
Sharp or heavy objects should
never be put on or in the dryer.
Check pockets for bolts, nuts etc.
10
Some pretreatment products can
damage dials, consoles and finish.
Do not use these products on or near
your dryer.
Cleaning drye; interior
Garments which contain unstable
dyes, such as denim blue jeans or
brightly colored cotton items, may
discolor the dryer interior. If the
interior is discolored, clean with
one of the following methods to
avoid staining later load items.
Powdered laundry detergent and
very warm water
Make a paste with detergent and
very warm water. Apply paste to
a soft cloth and scrub area until
all excess dye is removed. Wipe
thoroughly with a damp cloth.
Tumble a load of rags. -OR-
liquid spray household cleaner
Spray on stained area. Rub with
a cloth until all excess dye is
removed. Tumble a load of rags.
Vacation care
l Unplug power cord or turn off
electrical power.
l For gas dryers, close gas valve.
l Clean lint screen.

If you need service or assistance,
we suggest you follow these five steps:
1. Before calling for
assistance...
Performance problems often result
from little things you can find and fix your-
self without tools of any kind
IF YOUR DRYER DOES NOT RUN:
l Is the power supply plugged into a live
circuit with the proper voltage?
l Is the door closed tightly?
l Did you push the START Button?
l Have you checked your home’s main
fuses or circuit breaker box?
IF YOUR DRYER DOES NOT HEAT:
l The AIR setting is without heat.
l The last minutes of heat settings are with-
out heat.
l Is the gas turned on? If not, turn the Con-
trol Knob to OFF. Turn on gas. Wait 5 min-
utes. Reset controls and stort.
l An electric dryer uses a circuit breaker
or 2 fuses. If one fuse is blown, the dryer
may run, but not heat.
IF DRYING TIME SEEMS TOO LONG:
l Is the lint screen clean? See page 9 of
this book for cleaning instructions.
l See page 8 of this book and your”Dryer
Guide:’
2. If you need
assistance?. .
Call Whlrlpool COOL-LINE” service as-
slstance telephone number. Dial free
from anywhere in the U.S.:
l-800-253-1301
and talk with one of our trained Consul-
tants. The Consultant can instruct you in
how to obtain satisfactory operation from
your appliance or, if service is necessary,
recommend a qualified service com-
pany in your area.
3. If you need service?..
ai=/
- mi,fl
d
Whirlpool has a
01 _ nationwide net-
work of franchised
TECU-CARE
TECH-CARE- Serv-
; FRAN‘HlSEDSERVICE1 ice Companies.
TECH-CARE service
technicians are trained to fulfill the orod-
uct warranty and provide after-warranty
service, anywhere in the United States. To
locate TECH-CARE service in your area,
call our COOL-LINE service assistance
telephone number (see Step 2) or look in
your telephone directory Yellow Pages
under’
4. If you have a problem?..
Call our COOL-LINE service assistance
telephone number (see Step 2) and talk
with one of our Consultants, or if you pre-
fer, write to:
Mr. Robert Stanley
Division Vice President
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
5. If you need FSP’
replacement parts?.
FSP is a registered trademark of
Whirlpool Corporation for quality parts.
took for this symbol of quality whenever
you need a replacement part for your
Whirlpool appliance. FSP replacement
parts will fit right and work right, because
they are made to the same exacting
specifications used to build every new
Whirlpool appliance
* If you must call or write, please provide:
model number, serial number, date of
purchase, and a complete description
of the problem This rnformafion is
needed in order to better respond to
your request for assistance.
11

WHIRLPOOL” DRYER
WARRANTY DROOl
LENGTH OF WARRANTY
FULL ONE-YEAR
WARRANTY
From Date of Purchase
WHIRLPOOL WILL PAY FOR
FSP” replacement parts and repair laborto
correct defects in materials or workmanship.
Service must be provided by a franchised
TECH-CARE i service company.
WHIRLPOOL WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation of the dryer.
2. Instruct you how to use the dryer.
3. Replace house fuses or correct house wiring or plumbing.
4. Replace light bulbs.
B. Repairs when dryer is used in other than normal, single-family
household use.
C. Pick up and delivery. This product is designed to be repaired in
the home.
D. Damage to dryer caused by accident, misuse, fire, flood, acts
of God or use of products not approved by Whirlpool.
WHIRLPOOL CORPORATION SHALL NOT BELIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of
incidental or consequential damages so this limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Outside the United States, a different warranty may apply. For details, please
contact your franchised Whirlpool distributor or military exchange.
Part No. 3390211
c 1987 Whirlpool Cxporation Printed in U.S.A.