Whirlpool 27' User manual

IMPORTANT:
Read and save
these instructions.
Installer: Leave Installdion Instructions
Homeowner: Keep installation Instructions
27” Electric Built-in Combination:
l Microwave Oven and
Thermal Oven
- /?
Save Ihstallation Instn~ciions for local
electrical inspector’s use.
Whifl 01
fl
Homa &pliancS

Before you start...
Read Eleclriccrl and Carpenhy instructions.
Proper installation isyour responsibility. A
qualified technician should install this oven.
Make sure You have everyMing necessary
for correct installation. lt Isthe resgotibilitv of
the installer to comply with the in&all~on’
clearances specifed on the serial/ratina elate
The serial/rating plate is located dehing&e
Oven door on the front frame.
Check location where oven till be installed
Cabinel opening dimensions that are shown must be
used Given dimensions provide minimum clearance.
Contact surface must be solid and level.
The recessed inslallaiion area must provide complete
enclosure around me recess& portion of the oven.
AU OPENINGS 1~THEWALL OR FLOOR WHERE OVEN
tSTO BEINSTALLED MUST BESEALED.
Remove all packaging material from microwave
oven cavity Check mlcrowave Oven area for
damage- see WARNING below. If any damage is
evident, do not ooerate until microwave oven is
The location should be away horn strong draft
area. such as windows. doors, and strong
Testing vents or faM-SThe oven should be
Notated for conver lient use in the Ltifchen.
checked by an duthorized service technician.
“Note: hrm In”,,
Clearances specified are for
combusfible walls and malerials that
have a density of 20 or more pounds
per cubic 1001. No evaluation of
clearances has been made for
insfallalions adjacent fo malerials fhol
Elechicol ground isrequired
See Electrical requirements.
Blocking lhe oven venl may touse
cabinet damage and mr baking
flush wilh the bottom of fhe cabinet
Tools needed for
installation:
Electrical
requirements
A
Thb appliance must be
. connected to me otooer
electrical voltage and f&&cy as
spechied on the serial/rating plate.
Models rated at 7.0 kxv on 240 volts (5.3
kw on x)8 v&s) or mbre require 0
separate 4O-ampere circuit. Models
rated at 3.6 hv on 240 vdts (2.7 kw on
208 volts) or les require a separate 30
ampere circuit Fuse both sides of me
line. A timedelay fuse or circuit
breaker lsrecommended.
B ovm
MUST BECONNECTED WITH
. COPPER WIRE ONLY.
Parts provided
for installation:
Personal Injury Hazard
* Do Nol aHerr@ lo operale Ihe
n+crowave oven wilh Ihe door open.
l Do Nd tamper wilh or defeoi Ihe
safev inferlocks.
- Do Nd place objects between Ihe
ticrowave oven front face and
door.
- Do Nd allow soil or cleaner residue
lo accumulate on sealing surface of
the microwave oven door.
l Do Nol operale the Wcrowave oven
il CkJrMged.
- Do Nof operate Ihe mfcrowove oven
5 door is bent
-hinges and latches are broken or
kxse.
- dca seals, sealing surfaces or
glass are broken.
The microwave oven door must close
properly lo provide safe operation.
- Only have a qualified repair person
adjust. repair and check microwave
oven for microwave leakage cn?er a
repair ts made.
- Do No! use microwave for
commercial purposes. The
mfcrowove oven In lhis unit is
designed for household use c+.
Failure 10 follow these instructions could
resutl In exposure lo excessive
microwave energy.
Elechicol Shock Hazard
* Electrical ground is required on this
appliance.
- Improper conneciion of the
equipmenl-grounding conductor
line con resuil in a risk of elechicol
shock.
- Check with o quafiied electrician
il you ore in doubt as lo whether
Ihe appliance ir property
grounded.
- Do Nol hove a fuse in Ihe neulrol or
grounding circuit. A fuse in Ihe
neuirol or groundinq circuit could
resufl in el&hicof shock.
Failure lo follow these instructions
could result in o Bre, elecfrical shock
or other personal injury.
Save lnstollalion lnshucfions for
elechicaf inspeclofs use.
Elechical Shock Hazard
II is Ihe customer’s responsibilii:
l To contacl a quolired electrical
insloller.
- To assure that Ihe eleclrical
inslallallon is odequale and in
conformance wth Naiional Electrical
Code. ANWNFPA 70-lalesl edfiion.’
and all local codes and ordinances.
Failure to fdiow Ihere inshuctiis could
resuli in elechical shock.
Pencix~l Injury Hazard
* Securely fasten oven to cabinet
using Ihe hvo screws provided.
Failure lo do so could cause oven lo
mve or lip during use and resuli in
personal Injury. -
C
wire sizes and connections
. must conform to me
requirements of the National Electrical
Code ANSI/NFPA 70 - Ikrtest edition’
and all local codes and ordinances
for the kilowatt rating of the oven
Thisrating can be found on the
serial/rating plate located behind the
oven door on the front frame.
D
Thisappliance should be
n connected dire& to the
fused disconnect (or circuit breaker)
through flexible, armored or non-
metallic sheathed. copper cable (with
Panel A

grounding wire). The fiedble, armored
cable extending from the appliance
should be connected dire&+ to the
iunctbn box.
E
Locate the junction box to
m allow as much slack CISoossible
between the Junction box an’d ihe
appliance so that the oven con be
moved if servicing isever necessoly.
Do Not cut the conduit.
F
A U.L:listed conduit connector must
l be provided at the Junction box.
G
ii isthe personal responsibility
. and obligation of the
customer to contact a quoliWd
electWan to assure that me electial
installation b odequote and In
confomance VJim the Naiional
ElectrIcal Code ANWNFPA 7&k&&
edition.’ and all local codes and
ordinances.
Copies of me standard listed may be
obtained from:
’ National Fire Prdeclion Association
Botterymarch Pati
Quincy, Massachusetts 02269
H
A tiring diagram $ Included In
. the Tech Sheet. The Tech Sheet
islocated on bottom. behind the
lower vent grill.
Electrical
connection
Electrical Shock Hozord
* Eledrtcal ground is required on
this appliance.
- Do Not connect to the electrical
supply until appliance is
permanently grounded.
* Dtsconnecl power to the junction
box before making the electrical
connedion.
. This appliance must be
connected lo o grounded,
metallic. permanent wiring
system. or o grounding
connector should be connected
to the grounding terminal or wire
lead on Ihe appliance.
Failure to do so could result In Q
fire, personal injury or electrical
shock.
lhls appliance Ismanufactured him
white (neutra0 power supply wire and (
cabInetconnected. ereen grounding
tie lwkbd together. Connect the
appliance cable to the Jundon bow
throuah the U.L-llsted conduit
con&&tor. Complete elecirlcal
connection according to your
lnstotlatkn needs.
B. Where local codes
DO NOT permit...
Connecting the cabinet-grounding
conductor to the neuiral (white)
junction box wire: Cab!+ horn
power wpply
J”“t,lo” I I
Cob,.
A: Where local codes
permit... .‘- ., .+
Contiecttng the cablnel-grounding
condudor lo the neutral (whtte)
junction box wire:
Cabk horn
Jundlon
power supply
, ,
ct
es
1. Turn power supply off.
2. Connect three wires: green and
white appliance cable wires and the
white wire in the iunction box.
3. Connect the two black tires
together; then the two red wires
together. (See Figure 1.)
Now start...
With oven in kitchen.
1
Remove shlpping materials and
. protective film from microwove
oven and oven. Do Not remove the
loom shipping base d Ihb time.
Figure 2 from O”.”
1. Turn power supply On.
2. Connect the tiie appliance
cable tire to the neutral (whiie) wire
inJunct!on box.
3. Connect the Iwo black tires
together; men me two red wires
together. (see figure 2.)
4. Connect the grounding wire to o
grounded wire in the junction box or
to a grounded. copper cold water
3
Completely open oven door.
. Remove two oven door screws.
2
Remove and unwrap racks
. and omer parts from inside oven.
Remove the air grille taped to me top
or side of oven.
5. A separate copper grounding wire
(No.-10 minimum) MUSTbe connected
io a grounded metal cdd water pipe
by means of a clomp and then to the
external grounding connector screw.
Do Nd ground to a gas supply pipe OT
hol waler plpe. Do Not connect to
electrical suppk until appliance Ls
pemanentty grounded. (see Flgure 3.)
C. If connecting to a four-
wire electrical system...
Do Not connect the cabinet
grounding conductor lo the neutral
(white) Junction box wire.
Cabl. horn
POW.‘IUPPlY
I I
Figure 4 cab!.
from 0°C.”
1. Turn power supply ott.
2. Separate the green and white
appliance cable wires.
3. Connect the white oppllance
cable wire to the neutral (white) wire
in the junction box.
4. Connect the two black wires
together: then ihe hue red wires
together. (See Figure 4.)
5. Connect the green appliance
cable wire to the green grounding
wire in the Junction box.
Personal Injury Hazard
l Use both hands to remove oven
door.
. Grasp onty the sides of the oven
door.
. Do Not use handle or any portion
ot the hont hame or him for lining.
. Because ot the weight ond she
of the oven, two or more people
ore needed to move and solety
install oven.
Failure to properly grasp the oven
door or to Iti7 oven property could
resutl in damage lo product or
personal injury.
4
Close oven door to me broil
. position. Grasp lhe skies of the
oven door and pull the door up and
off the hinges to remove. Set dmr
aside.
Before moving oven acrass floor.
check thoi oven is on shipping
base or Me oven onto
cardboard or hardtird.
Failure to follow these instructions
may resuli in danoge to floor
coverinq.
5
Turn power supply off. Move
. oven close to final oosition.
Remove and discord shipping base,
cardboard or hardbwrd. Feed
appliance cable through opening in
cabinet. Make electlical conn@fions.
See Electrical requirements and
ElecMcol connechon sections. Panels A
and 8.
Panel B

Product Damage
Carefully push against the seal
area on the oven hont hame
when pushing oven into cabinet.
Do Not push against outside
edges.
Foilure to follow this instruction can
red In damage to oven rinish.
Uft dll oven up Into cabinet cutout
using the oven opening 0s an area
tog+ ,
Purh ogalnst seal area of front frame to
push oven into cabinet.
Securely taslen oven to cabinet
using the two screws provided.
Failure to do so could cause the
oven to move or tip during use ond
resutt in personal injury or product
7
Center oven in cabinet cutout.
n Use two screws through the
mounting holes in the front f~aame
of the oven to secure oven to cabinet.
Do Not overtighten screws.
8
Install lower air grille using the
. three screws provided.
9
InstoU 0 troy in mlcrowave
m oven Q microwave oven Isso
equipped). Place oven racks in oven
Replace the oven door by porttally
fitting the door hinges into the hinge
slots. Pulldoor slightly towards you;
then Slide doa completely in place.
ReInstoll the two oven do& shrews. of
door does not close. vou have not
Pushed hinges completeh/ Into frame.
Turn power supply on.
10
Check the operation of the
moven. Set oven selector
switch to ‘BAKE-. Set oven control
knob to 350°F. The bottom and upper
outer elements should glow red. The
oven Indicator light should be on and
me oven should be heattng. Turn
selector switch ond control knob to
-OFF-.
11
Check the operation of the
n oven broil element. Set oven
selector switch and temperature control
knob to ‘E!mll-. Both of me top elements
should glow red The oven lndlcator light
should be on and the oven should be
heating. Turn selector s-witch and control
knob to ‘OFF’.
Personal Injury/
Property Damage Hazard
- Handle healed waler with care.
Mishandling hot water or steam
could result in a serious burn.
- Maintain at least t/2 quort (or
l/2 ltter) of wafer in container
when testing operalion of
microwave oven.
Failure to maintain proper water
level could result In damage to
container.
J
\ 5.
Numbers
correspond
to steps.
12
Check the operamn of the
l mlcrowave oven.
. Fillo mIcrowavetie container with
one quart of water and place
container inside microwave oven.
Close door finly
l Set microwave oven cooking time
to ten minutes.
l Press the ‘START- pod. lhe Interior
mlcrowave oven light should be on
and the remalnlng cooking time
should be displayed.
. When dkplay reads ‘5:00.- open
mlcrowave oven door. The
mlcrowave oven should stop
cooking.
l Close door firmly. The interior
mlcrowave oven light should turn off.
l Pres the ‘START’ pad. Microwave
oven should begin cooklng and the
mlcrowave oven Inteti light shou!d
beon.
l Repeat opening and closing of
microwave oven door several Hmes
during the remaining cooking time.
l Let microwave oven complete
cooking time. A tone will xKlnd for
two seconds at end of cmkng time
and microwave oven will shut off.
l Open microwove oven door and
carefulty remove container. Water in
container should be hot
‘one1 C

If oven does not
operate...
Check that the circuit breaker isnot
tripped or the fuse blown.
Check that the powersuppiy cord is
plugged into the wall receptacle.
Part No. 3181680
01 W 1 Whirlpool Corporation
If vou need
as&stance...
The Whiripool Consumer Assistance
Center will answer any questions
about operating or maintaining your
oven not covered in the lnstallotion
Instructions. The Vvhirlpool Consumer
Assistance Center number Isopen 24
hours a day, 7 days a week. Just dial
(800) 253-l 301 -the call isfree.
When you call, you will need the
oven model number and serial
number. Both numbers con be found
on the serial/rating plate behind the
oven door on the front frame.
Prepared by Whirlpool Corporation Benton Ho&or, Michigan 4X22
If you need
service...
In the event your Whirlpool
appliance should ever need service,
call the dealer from whom you
purchased the appliance or a
Whiripool~uthorlzed service
company. The dealer or service
company Islisted in the Yellow Pages
of your phone directory under
‘Appliinces - Major - Service or
Repair.’ You con also obtain the
name and number by dialing, free
within the continental United States,
the Whirlpool Consumer A&stance
Center number - (800) 253-l 301. A
special operator will tell you the
name and number of your nearest
Whirlpool-author&d service
con-pony.
Printed in USA