Whirlpool RH7630XL User manual

I-
’ VENTLESS KITCHEN RANGE HOOD
FOR 12O.V. OPERATION
Tiiifl 01
4a
II
I
KITCHEN
RANGE HOOD
MODEL
RH7630XL
READ AND SAVE THESE INSTRUCTIONS
Betore you begin, read the following lnstructlons
completely and carefully. It followed, they will simplify
the installation job.
IMPORTANT: OBSERVE ALL GOVERNING CODES
AND ORDINANCES
SAVE THESE INSTRUCTIONS FOR THE LOCAL
ELECTRICAL INSPECTOR’S USE
1. Remove screw holding junction box cover.
2. Remove proper electrical knockout See Figure 1.
3. Lift the hood into position. Mark location of four
mounting holes.
4. Remove hood and start all four screws in center of
narrow neck of keyhole slot marked on cabinet bottom. (Fig.
2).
5. Lift into position on four screws simultaneoulsy feeding
electrical wire through knockout.
8. Complete electrical wiring in junction box according to
the National Electrical Code and applicable Local codes.
for an easier installation, remove the filters and the three
assemblies shown in Fig. 3. This reduces the weight about
40%. The blower cover and light frame assembly are held into
place with thumb screws. To remove the blower assembly,
first unplug the blower supply cord from the junction box.
Remove the packing screw from the blower retaining rod,
then pull the blower retaining rod to one side, freeing it from
NOTE: This unit must be permanently grounded.
7. Tighten screws to secure hood. Be sure screw head is in
narrow neck of keyhole slot.
8. Replace junction box cover.
9. Replace blower cover, light frame assembly and filters.
between the bumps on the blower housing. 10. Replace blower.
TOOLS AND MATERIALS REQUIRED
l Drill, electric or ratchet drive, with 1-W’ wood bit (to
drill an access hole in the cabinet or kitchen wall for the
electric power line.)
l One common head screwdriver (to secure hood
mounting screws to the cabinet and hood sheet metal
parts).
l Pliers (for opening knockouts).
l Pencil, ruler and level for marking cabinet locations.
l Saber saw or keyholesaw for cutting the wall or cabinet
openings.

OPERATION AND CARE OF UNIT IMPORTANT SAFEGUARDS FOR
ELECTRICAL APPLIANCES
When using electrical appliances, basic safety precautions
should always be followed including the following:
1. Read and follow all instructions.
2. Close supervision is necessary when any appliance is
used by or near children.
3. To avoid providing fuel for a grease pan fire,clean lint
and grease from all hood surfaces-interior and exterior.
Be sure to remove and clean air filter every three months.
4. Do not saturate electrical connections, switches, and
motor in water during cleaning. Remember, WATER AND
ELECTRICITY DO NOT MIX!
5. If any electrical malfunction becomes evident during
use, disconnect power to hood at your home fuseor
breaker box.
CARE OF FILTERS:
A. ALUMINUM FILTER: For greatest efficiency, the
permanent type aluminum filter should be removed and
cleaned periodically.
To clean, the filter should be soaked in hot water detergent,
then thoroughly rinsed. The aluminum filter can be washed
in a dishwasher.
8. CHARCOAL FILTER: This filter should be inspected
periodically and when it becomes saturated should be
replaced. There are no effective means of reactivating
charcoal filters.
CARE OF EXTERIOR SURFACES:
Your range hood is a beautifully finished addition to your
kitchen. To preserve its lasting beauty, clean with a mild
detergent. DO NOT use abrasive cleaners.
LIGHTING
Select two light bulbs up to 75 watts each to acheive desired
lighting level.
BLOWER CONTROL
This range hood has a solid state motor speed control. After
setting the control to a desired speed, it will take
approximately 15 seconds for the blower to respond to that
setting.
For most effective removal of smoke and odors, turn on fan at
beginning of cooking operation and allow to run until smoke
and odors are removed from room.
r
LIGHT FRPhX
ASSEMBLY
KEYHOLE SLOT
IN CANOPY
(IN INSTALLATION
PARTS BAG)
FIG. 2
EL%‘.ER CRADLE
.ELOwER
RETAINING
ROD
-JUNCTION
BOX
FIG. 3
If you need service or assistance, we suggest you follow these four steps:
4
l If you bavc P problem...
Paae 2