Whirlpool AWD80AGP User manual

SERVICE MANUAL
Model:AWD80AGP
Contents

1
1．Introduction ---------------------------------------------------------------------------------2
2．Technical data----------------------------------------------------------------------------------2
3．Control panel--- -------------------------------------------------------------------------------2
4．Functions---------------------------------------------------------------------------------------4
5．Constructive parts-----------------------------------------------------------------------------4
6．Installation--------------------------------------------------------------------------------------8
7．Alarms-------------------------------------------------------------------------------------------9
8．Diagnostics system-----------------------------------------------------------------------------9
9．Electrical circuit--------------------------------------------------------------------------------10
1. Introduction

2
1.1 Purpose of this manual
The purpose of this service manual is to provide service engineers who already have basic
Knowledge necessary to repair air vent dryers with electronic control systems.
1.2 Important
Repairs to electrical appliances must be carried out only by qualified service engineers
Before touching internal components, always remove the plug from the power socket
2. Technical Data
Voltage 220V 60Hz
Weight 38 Kg
Heater 230V 2100W
Dimention
WxDxH 595*555*850mm
Drying system Air vented
Humidity control Conductimetric sensor
Motor Single-phase asynchronous motor with capacitor
Temperature control NTC sensor
Energy efficiency C
Error alarms 3
3．
．．
．Control Panel
12 3 4 5 6 7 8
1. Buzzer 7. Indicator Lights

3
2. Quick Drying
3. Half Load Cooling
4. Start Delay Anti-Crease
5. Display (LED) Filter
6. Start/Pause 8.Program Selector
4. Functions

4
Buzzer
This function is used to indicate end of cycle
Start Delay
This function need to press before start/ pause
Quick
Only "Jeans" ,"Towels", "Normal" program ,you can use the function.
Quick option and Half Load option cannot be selected at the same time.
Half Load
Only “Jeans” “Towels” “Normal” ”Blankets” “Delicate” “Footwear” “Shirts” “Sport” cycle, you can
use the function.
Quick option and Half Load option cannot be selected at the same time.
Led display
When select a program, The Led display shows remaining time,
When select not correct program, the Led display shows error code
Start/ pause
After select the program ,press this button to start the dryer. the dryer cannot work if you open the
door during the drying cycle .the machine can continue to work after close the door and press the
start button .In this situation, “Start/pause” indicator blink in order to tell you to press the button.
Indicator lights
Drying: It shows the dryer is in drying phase
Cooling: It shows the dryer is in cooling phase ,there will be 10 minutes in this phase.
Anti-Crease: It shows the drying is finished and the anti-creasing routine begin ,it last 10
minutes for consul model,30 minutes for whirlpool model.
Filter：After use the dryer ,the indicator will blink and tell you should clean the filter.
5. Constructive Parts

5
1. Door As
2. Control Panel As
3. Cabinet
4. Top Cover As
5. Door Lock AS
6. Screw Cap
7. Door Gasket
8. Drum Supporter As
9. Motor As
10. Micro-V Belt
11. Drum AS
12 Vent Pipe
13 Vent Pipe Cuff
14 Back Cover
15 Reset Button As
16 Power Cord
17 Vent Pipe Cover
18 Under Base
19 Adjustable Leg
20 Leg
21 Idler As
5.1 Control Panel As
22 Select Knob
23 Knob Bracket
24 Control Panel
25 Knob Shaft
26 Select Button
27 Display Window
28 Power Button
29 Button Bracket
30 LED Display
31 PCB Case
32 Operate PCB
33 Main PCB
34 PCB Cover
5.2 MotorAs

6
35 Front Fan Cover
36 Fan As
37 Rear Fan Cover
38 Venting Gasket
39 Motor Cushion
40 Motor Fixture
41 Motor
42 Capacitance
43 Motor Bracket
44 Relay Bracket
5.3 DoorAs
45 Door Outer Frame
46 Door Inner Window
47 Door Inner Frame
48 Door Hook
49 Door Hinge Cap
50 Door Hinge
51 Hinge Support Plate

7
5.4 Drum SupporterAs
52 Drum Support Cover
53 Filter As
54 Lamp Socket
55 Lamp
56 Drum Supporter
57 Drum Guide Plate
58 Lamp Gasket
59 Lamp Cap
60 Felt
61 Moisture Sensor
62 Venting Gasket B
5.5 Door Lock AS
63 Door Lock Body
64 Hook Holder
65 Door Lock Cover
66 Micro Switch
67 Micro Switch Cover
68 Hook Holder Spring
5.6 DrumAs

8
69 Inside Small Cover
70 Lifter
71 Inside Bucket Rivet Joint Module
72 Heater Fixture B
73 Heater
74 Heater Plate
75 Thermostat 170℃
76 Thermostat Fixture
77 Thermostat 85℃
78 Drum As Fixture
79 Drum Shaft
80 Inside Bucket Bearing Module
81 Bearing Supporter B
82 Spring
83 Spring Washer φ8
84 Nut
85 Thermostat Fixture
86 Bracket
Attachment Name Quantity
Hose 1
User Manual
1
6. Installation
6.1 Unpack all packaging, include the bottom foam, check the machine situation.
6.2 Install the dryer as follow steps:
6.21 Install the Vent Hose
There are two outlets in the dryer ,one is at the back ,the other is in the left side.
Connect the hose to whichever is the more convenient by pulling the ring nut (A)
From the vent outlet at the back ,aligning arrows of the hose and ring nut ,fastening
By screwing hose to the direction of arrow and pushing it firmly back into place .
the unused vent should be sealed with the special snap cover(B).

9
6.22 Level adjustment
● Adjust the level to avoid vibration and noise
Machine must be placed in a clean place ,no water ,ice and combustible materials there.
To keep vibration and noise to a minimum when the dryer is in use ,it should be placed
on a firm level surface.
● If the dryer is not completely leveled ,loosen the locknuts ,adjust the adjustable feet to
Lower the dryer by turning right and to ascend it by turning left .Tighten the locknut after
Insuring the dryer is level.
7. Alarms
Alarm Description Possible Fault Action
Dop
Door switch
Door is open
Harness disconnect
Wire faulty
Door lock faulty
PCB faulty
Close the door
Connect the harness
Change wire
Change door lock
Change PCB
E1 NTC sensor faulty NTC sensor faulty PCB faulty
Wire faulty
Change wire
Change PCB
Change wire