5019 312 10276
Whirlpool is a registered trademark of Whirlpool USA
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with standard IEC 60 456. Consumption data in the home may vary with respect to the values in the
table in relation to the water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the
household conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
***Reference Programme for Energy Label
1. Close the drum door flaps and check that they are
properly locked.
2. Add detergents and additives into the dispenser to
no more then the “MAX” level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Chlorine bleach
•Stainremoveragents
• Anti-scale agents (if necessary)
3. Turn the programme selector knob to the
desired programme.
The remaining time of the chosen programme is
shown in the display (in hours and minutes) and
the indicator light of the “Start/Pause” button
flashes.
The predefefined temperature & spin speed
corresponding to the selected programme are
indicated in the display. The temperature (+/-)
and spin speed can be changed by pressing
the corresponding button.
When you select an option authorized by the
programme, the corresponding indicator lights up,
except if the combination of programme,
additional options and temperature is not possible.
“Easy Ironing” button
• Can be used together with “Cotton”, “Synthetic” and
“Daily Mixed” programmes to make ironing easier.
• Increases the water quantity in rinsing and the
clothes are spun in a softer manner.
“Eco plus” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
• Only for heavily soiled loads (for example mud,
granular dirt).
“Intensive Rinse” button
• The amount of water is increased to ensure a
more intensive rinse.
• This option is particularly suitable for areas with
very soft water or washing linen laundry for
people with skin allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing from fading.
• This option is particularly recommended for the
“Synthetic”, “Delicate” and “Daily Mixed”
programmes.
• Use this option if you want to postpone spinning
to a later time, or if you want to drain only.
CONSUMPTION DATA
Programme
Temperature Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 90/40 5.0 49**/48 1.60/0.60 2:05/2:00
Cotton 60 5.0 48 0.95 2:05
Cotton with Eco plus*** 60 5.0 48 0.85 2:10
Daily Mixed 40 3.0 45 0.45 1:00
Synthetics 60/40 2.0 55/50 0.70/0.50 1:30/1:15
Rapid Plus 30 3.0 35 0.40 0:30
Delicates 40 1.5 50 0.50 0:45
Wool 40 1.0 50 0.50 0:45
Handwash 30 1.0 35 0.40 0:35
PREPARATION OF WASH CYCLE
SELECT THE DESIRED OPTION
Note: The programme with “Rinse Hold” stops
when the “Rinse Hold” is indicated in the
display.
Appliance in “Rinse Hold”:
• If you want to continue the programme press
the “Start/Pause” button again: The
programme will terminate automatically with
the selected spin cycle. If the load is dry then
please press the “Start/Pause” button.
• If you do not wish to spin the load, turn the
programme selector knob to the “Drain”
programme and press the “Start/Pause” button.
“Spin Speed Reduction” button
• Every programme has an automatically allocated
maximum spin speed.
• Press the button until you have reached the
requested spin speed indicated in the display.
•If the spin speed “0” is selected, the final spin is
cancelled, but not the intermediate spins. The
programme ends with a drain cycle.
The “Start Delay” button allows the user to run
the appliance at his convenience, for example at
night when electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start Delay” button several times to
select the delay time by 1 to 24 hours (selected
delay is indicated in display);
•Pressthe“Start/Pause” button. The indicator
light of the “Start/Pause” button lights up, the
lamp of the “Start Delay” button flashes and the
selected delay is indicated in the display.
• The time delay indication disappears when the
programme starts and is replaced by the
remaining time.
• The number of hours preselected can be reduced
later by pressing the “Start Delay” button again.
To cancel the pre-selected “Start Delay”
• Turn the programme selector to the “ ”
position.
• Reselect the desired programme and options
and press the “Start/Pause” button.
Open the tap and press the “Start/Pause” button.
The indicator light of the “Start/Pause” button lights
up. At programme start the sequences reached by the
programme are indicated in the display.
Note: If there's a power cut during the cycle, the
programme will continue automatically from where
it was interrupted.
For safety reasons, the lid is locked during certain
phases of the cycle. At the end of the cycle or
during an interruption, the lid unlocks automatically
after about 1 minute.
• Upon programme end “ ” is shown in
the display.
1. Turn the programme selector to the “ ” position.
2. Close the tap.
3. Open the lid and the door flaps and unload the
appliance.
Press “Start/Pause” button. Select new programme
and/or new options, temperature and spin speed and
press “Start/Pause” button again. The new
programme will continue at the same position where
the previous programme was interrupted. Do not add
detergent for this programme.
Note: The “Start Delay” and “Prewash” cannot be
selected after a programme change.
If, for adding some forgotten pieces of clothing or any
other reasons, you wish to interrupt or pause the
programme for a certain time and continue it later:
1. Press the “Start/Pause” button.
The light flashes.
2. After the desired pause, press again on the
“Start/Pause” button.
To cancel a programme please press Reset button
for 3 seconds.
Note: After power cuts or disconnection from the
mains after programme end, the LCD display may
show the previously selected settings. In this case
we suggest to check laundry’s humidity in drum.
If laundry is damp, the cycle finished properly.
Unload the drum and press Reset Button for
3 seconds before selecting a new cycle for
next laundry.
START DELAY
PROGRAMME START
LID LOCK
END OF WASH CYCLE
CHANGE THE PROGRAMME OR OPTIONS
DURING THE CYCLE
PAUSE/INTERRUPT A PROGRAMME
CANCEL PROGRAMME
