Whirlpool Cabrio WTW6200S User manual

L-81
JOB AID
Part No. 8178583
AUTOMATIC
WASHER
CONSUMER CARE TECHNICAL
EDUCATION GROUP PRESENTS
MODELS: WTW6200S & WTW6300S

- ii -
FORWARD
This Whirlpool Job Aid, “Cabrio™ Automatic Washer” (Part No.8178583), provides the In-Home
Service Professional with information on the installation, operation, and service of the Cabrio™
Automatic Washer. For specific information on the model being serviced, refer to the “Use and
Care Guide,” or “Tech Sheet” provided with the washer.
The Wiring Diagram used in this Job Aid is typical and should be used for training purposes only.
Always use the Wiring Diagram supplied with the product when servicing the unit.
GOALS AND OBJECTIVES
The goal of this Job Aid is to provide information that will enable the In-Home Service Professional
to properly diagnose malfunctions and repair the Cabrio™ Automatic Washer.
The objectives of this Job Aid are to:
• Understand and follow proper safety precautions.
• Successfully troubleshoot and diagnose malfunctions.
• Successfully perform necessary repairs.
• Successfully return the washer to its proper operational status.
Copyright © 2006, Whirlpool Corporation, Benton Harbor, MI 49022
WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on
our products by anyone other than authorized In-Home Service Professionals.

- iii -
TABLE OF CONTENTS
Page
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Washer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Model & Serial Number Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Model & Serial Number Label & Tech Sheet Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Agitator Wash Program/Selectability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
INSTALLATION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
PRODUCT OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Theory Of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Washer Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Washer Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
COMPONENT ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Removing The Encoder And The User Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Removing The Water Inlet/Dispenser Valve Assembly, Power Supply Cord,
And Machine/Motor Control & Pressure Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Removing A Dispenser, The Fresh Fill Inlet Valve, And The Lid Lock . . . . . . . . . . . . . . . . 4-6
Removing The Lid And A Lid Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Removing The Basket & Basket Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Removing The Drain And Recirculation Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Removing The Drive Motor & Rotor Position Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Removing The Tub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Accessing The Pressure Transducer Tubing, Recirculation Tube,
And Drain Pump Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
COMPONENT TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Water Inlet/Dispenser Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Drain Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Recirculation Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Lid Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Drive Motor Stator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
DIAGNOSTICS & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Display Fault/Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Diagnostic Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Troubleshooting Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Accessing & Removing The Electronic Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

- iv -
— NOTES —

1-1
GENERAL
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING.” These words mean:
All safety messages will tell you what the potential hazard is, tell you how to reduce the
chance of injury, and tell you what can happen if the instructions are not followed.
You can be killed or seriously injured if you don’t
immediately follow instructions.
You can be killed or seriously injured if you don’t
follow instructions.
DANGER
WARNING

1-2
MODEL & SERIAL NUMBER DESIGNATIONS
MODEL NUMBER
SERIAL NUMBER
SERIAL NUMBER C T 41 10200
MANUFACTURING SITE
C = Clyde, OH
YEAR OF PRODUCTION
T = 2006
WEEK OF PRODUCTION
41 = 41st Week
PRODUCT SEQUENCE NUMBER
MODEL NUMBER W T W 6 2 00 S W 0
BRAND
W = Whirlpool
E = Estate
R = Roper
I = Inglis
ACCESS / FUEL
T = Top Load G = Gas
F = Front Load H = Horizontal
W = Work Space V = Vertical
E = Electric
PRODUCT
W = Washer P = Pedestal
D = Dryer B = Combo
T = Thin Twin C = Compact
SERIES
1 = Innovation 6 = Oasis
2 = Commercial 7 = Merloni
3 = Compact 8 = Horizon
4 = Stack 9 = Duet/Combo
5 = LEAP
PRICE POINT LEVELS (1 - 7)
TRADE PARTNER
00 = Brand 30 = NATM
10 = SBC 40 = Lowe’s
20 = Best Buy
YEAR OF INTRODUCTION
S = 2006
T = 2007
COLOR CODE
W = White w/Silver Metallic Console
G = Biscuit w/Gold Metallic Console
B = Black w/Black Metallic Console
ENGINEERING CHANGE
0 = Basic Original Release
1 = First Revision

1-3
MODEL & SERIAL NUMBER LABEL &
TECH SHEET LOCATIONS
The Model/Serial Number Label and Tech Sheet locations are shown below.
Model/Serial Number Location
Tech Sheet Location
(Access Under Cabinet Top)

1-4
SPECIFICATIONS
MODEL NUMBERS WTW6200SW WTW6300SW, G, B
PRIMARY FEATURES
CAPACITY (DOE) 3.8 CU. FT. 3.8 CU. FT.
USABLE CAPACITY 18 LBS (8.16 KG) 18 LBS (8.16 KG)
MAX SPIN SPEED 950 950
EXTERIOR
LID FINISH POWDER COAT POWDER COAT
LID SOLID GLASS
TOP FINISH POWDER COAT POWDER COAT
AGITATOR DUAL ACTION DUAL ACTION
SOUND PACK Q. WASH Q. WASH PLUS
TUB WRAP NO NO
MASTIC (FRONT) 1 - 4 X 12 PIECE 1 - 4 X 6 PIECE
CABINET PAD NO YES
LID SEALS NO YES
MAIN DRIVE MOTOR BRUSHLESS PERM MAGNET BRUSHLESS PERM MAGNET
DISPENSERS 3 (ECONOMY) 3 (ECONOMY)
MAIN DETERGENT YES YES
TYPE FLUSH FLUSH
CAPACITY 2/3 CUP 2/3 CUP
BLEACH YES YES
TYPE FLUSH/TIMED FLUSH/TIMED
CAPACITY 1 CUP 1 CUP
FABRIC SOFTENER YES YES
TYPE AGITATOR CUP FLUSH/TIMED
CAPACITY 1/2 CUP 1/2 CUP
CYCLE DEFINITIONS
# OF CYCLES 7
HEAVY DUTY
NORMAL
WHITEST WHITES
DELICATES
PERM PRESS / CASUAL
HANDWASH / WOOL
DARKS / COLORS
7
HEAVY DUTY
NORMAL
WHITEST WHITES
DELICATES
PERM PRESS / CASUAL
HANDWASH / WOOL
DARKS / COLORS
OPTIONS
FINAL SPIN SPEEDS VARIABLE / NON SELECTABLE VARIABLE / NON SELECTABLE
SOAK PRE SOAK SOAK (AUTO)
CATALYST OPTIONS DEEP CLEAN
EXTRA RINSE
DEEP CLEAN
EXTRA RINSE

1-5
MODEL NUMBERS WTW6200SW WTW6300SW, G, B
SECONDARY
EOC OFF / LOUD OFF / LOUD
TIME REMAINING YES YES
TEMPS 4 ATC 4 ATC
ATC TEMPS H/C , W/W, W/C, C/C H/C , W/W, W/C, C/C
AUTO WATER LEVEL YES YES
WATER LEVELS SMALL - 3.1˝ (8 CM) ABOVE BASKET BOTTOM
MEDIUM - 8.5˝ (22 CM) ABOVE BASKET BOTTOM
LARGE - 9.5˝ (24 CM) ABOVE BASKET BOTTOM
SUPER - 12˝ (30 CM) ABOVE BASKET BOTTOM
SMALL - 3.1˝ (8 CM) ABOVE BASKET BOTTOM
MEDIUM - 8.5˝ (22 CM) ABOVE BASKET BOTTOM
LARGE - 9.5˝ (24 CM) ABOVE BASKET BOTTOM
SUPER - 12˝ (30 CM) ABOVE BASKET BOTTOM
SOIL LEVELS 3 3
STATUS LED’S WASH (4) / STATUS (3)
SOAK
WASHING
RINSING
SPIN
DONE
ADD-A-GARMENT
LID LOCKED
WASH (4) / STATUS (3)
SOAK
WASHING
RINSING
SPIN
DONE
ADD-A-GARMENT
LID LOCKED
ADDITIONAL
COLORS WHITE WHITE / BISCUIT / BLACK
SIZE ( W X D X H ) 28 X 27 X 42 IN (71.2 X 68.5 X 106.6 CM) 28 X 27 X 42 IN (71.2 X 68.5 X 106.6 CM)
WEIGHT (IN CARTON) 165 LBS (74.8 KG) 165 LBS (74.8 KG)

1-6
AGITATOR WASH PROGRAM / SELECTABILITY
D = Default Setting
x = Selectable Setting
o = Not Selectable

2-1
INSTALLATION INFORMATION
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before
starting installation. The parts supplied are in
the washer basket.
Tools needed for connecting the drain
hose and water inlet hoses:
Pliers that open to 1-9/16˝ (3.95 cm)
Flashlight (optional)
Parts Supplied:
•
•
Alternate Parts
Your installation may require additional parts.
If you are interested in purchasing one of the
items listed here, call the toll-free number on
the cover or in the “Assistance or Service”
section of the “Use & Care Guide.”
Tools needed for securing the drain hose
and leveling the washer:
Adjustable or open end wrench 9/16˝
(14 mm)
Level
Wood block
Ruler or measuring tape
•
•
•
•
A. Drain hose form
B. Water inlet hoses (2)
C. Flat water inlet hose washers (4)
D. Beaded tie strap
A B C
D
If You Have: You Will Need to Buy:
Laundry tub or
standpipe taller
than 96˝ (2.4 m)
Sump pump system (if not already
available)
1˝ (2.5 cm)
diameter
standpipe
2˝ (5 cm) diameter to 1˝ (2.5 cm)
diameter standpipe adapter,
Part Number 3363920 and connector kit
Part Number 285835
Overhead sewer Standard 20 gal. (76 L) 39˝ (99 cm) tall
drain tub or utility sink, sump pump and
connectors (available from local
plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose,
Part Number 8318155 and connector
kit, Part Number 285835
Water faucets
beyond reach of
fill hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Lint clogged drain Drain protector, Part Number 367031

2-2
LOCATION REQUIREMENTS
Selecting the proper location for your washer
improves performance and minimizes noise
and possible washer “walk.”
The washer can be installed in a basement,
laundry room, closet, or recessed area. See
“Drain System.”
IMPORTANT: Do not install or store the wash-
er where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
A water heater set to deliver 120°F (49°C)
water to the washer.
A grounded electrical outlet located with-
in 4 ft (1.2 m) of where the power cord is
attached to the back of the washer. See
“Electrical Requirements.”
Hot and cold water faucets located within
3 ft (90 cm) of the hot and cold water fill
valves, and water pressure of 20-100 psi
(138-690 kPa) for best performance.
A level floor with a maximum slope of
1˝(2.5 cm) under entire washer. Install-
ing the washer on carpeting is not recom-
mended.
A sturdy floor to support the washer
weight (washer, water and load) of 315 lbs
(143 kgs).
Do not store or operate your washer in tem-
peratures at or below 32°F (0°C). Some wa-
ter can remain in the washer and can cause
damage in low temperatures.
•
•
•
•
•
INSTALLATION SPACING FOR RECESSED
AREA AND CLOSET INSTALLATIONS
The following spacing dimensions are rec-
ommended for this washer. This washer has
been tested for installation with spacing of 0˝
(0 cm) clearance on the sides. Recommend-
ed spacing should be considered for the fol-
lowing reasons:
Additional spacing should be considered
for ease of installation and servicing.
Additional spacing should be considered
on all sides of the washer to reduce noise
transfer.
For closet installation with a door, minimum
ventilation openings in the top and bottom
of the door are required. Louvered doors
with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also
be considered.
•
•
•
•
A. Front view
B. Side view
C. Closet door with vents
ABC
17"*
(43.2 cm)
1"
(2.5 cm)
1"
(2.5 cm)
27-1/2"
(69.9 cm)
1"*
(2.5 cm)
27"
(68.6 cm)
5"*
(12.7 cm)
14" * max.
(35.6 cm)
3"*
(7.6 cm)
3"*
(7.6 cm)
24 in. *
(155 cm )
2
2
48 in. *
(310 cm )
2
2
* Required spacing

2-3
AB
(99 cm)
39"
DRAIN SYSTEM
The washer can be installed using the stand-
pipe drain system (floor or wall), the laundry
tub drain system, or the floor drain system.
Select the drain hose installation method you
need. See “Tools and Parts.”
STANDPIPE DRAIN SYSTEM—WALL OR
FLOOR (VIEWS A & B)
The standpipe drain requires a minimum di-
ameter standpipe of 2˝ (5 cm). The minimum
carry-away capacity can be no less than 17
gal. (64 L) per minute. A 2˝ (5 cm) diameter
to 1˝ (2.5 cm) diameter standpipe adapter kit
is available. See “Tools and Parts.”
The top of the standpipe must be at least 39˝
(99 cm) high and no higher than 96˝ (244 cm)
from the bottom of the washer.
LAUNDRY TUB DRAIN SYSTEM (VIEW C)
The laundry tub needs a minimum 20 gal.
(76 L) capacity. The top of the laundry tub
must be at least 39˝ (99 cm) above the floor
and no higher than 96˝ (244 cm) from the
bottom of the washer.
FLOOR DRAIN SYSTEM (VIEW D)
The floor drain system requires a siphon break
that may be purchased separately. See “Tools
and Parts.”
The siphon break must be a minimum of 28˝
(71 cm) from the bottom of the washer. Addi-
tional hoses might be needed.
CD
39"
(99 cm)
28"
(71 cm)

2-4
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15- or 20-
amp, fused electrical supply is required. A
time-delay fuse or circuit breaker is recom-
mended. It is recommended that a sepa-
rate circuit serving only this appliance be
provided.
This washer is equipped with a power sup-
ply cord having a 3 prong grounding plug.
To minimize possible shock hazard, the
cord must be plugged into a mating, 3
prong, grounding-type outlet, grounded
in accordance with local codes and ordi-
nances. If a mating outlet is not available,
it is the personal responsibility and obli-
gation of the customer to have the prop-
erly grounded outlet installed by a qualified
electrician.
If codes permit and a separate ground wire
is used, it is recommended that a qualified
electrician determine that the ground path
is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are
not sure the washer is properly grounded.
Do not have a fuse in the neutral or ground
circuit.
•
•
•
•
•
•
•
ELECTRICAL REQUIREMENTS
GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be grounded. In the event
of a malfunction or breakdown, grounding
will reduce the risk of electrcal shock by
providing a path of least resistance for elec-
tric current. This washer is equipped with a
cord having an equipment-grounding con-
ductor and a grounding plug. The plug must
be plugged into an appropriate outlet that
is properly installed and grounded in accor-
dance with all local codes and ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can result
in a risk of electric shock. Check with a quali-
fied electrician or serviceman if you are in
doubt as to whether the appliance is properly
grounded.
Do not modify the plug provided with the
appliance—if it will not fit the outlet, have a
proper outlet installed by a qualified electri-
cian.
For a permanently connected washer:
This washer must be connected to a ground-
ed metal, permanent wiring system, or an
equipment-grounding conductor must be
run with the circuit conductors and connect-
ed to the equipment-grounding terminal or
lead on the appliance.
WARNING

2-5
INSTALLATION INSTRUCTIONS
WARNING
Excessive Weight Hazard
Use two or more people to move and
install washer.
Failure to do so can result in back or
other injury.
NOTE: To avoid floor damage, set the washer
onto cardboard before moving across floor.
IMPORTANT:
Be sure the foam shipping base has been
removed from the bottom of the washer as
directed in the Unpacking Instructions.
If foam shipping base has not been re-
moved, be sure lid is secured with tape be-
fore laying washer on its back.
Removing the foam shipping base is nec-
essary for proper operation.
REMOVE SHIPPING BASE
AND PACKING RING
1. Place cardboard supports from shipping
carton on floor behind washer for sup-
port.
2. Using 2 or more people, tip the washer
onto its back and place on cardboard
supports.
3. Remove foam shipping base.
•
•
•
4. Set washer upright.
5. Remove tape from lid. Open lid and re-
move foam packing ring from washer tub.
Keep foam packing ring in case you need
to move the washer in the future.
CONNECT DRAIN HOSE
Proper connection of the drain hose protects
your floors from damage due to water leak-
age. Read and follow these instructions.
The drain hose is connected to your washer
and is stored inside the washer cabinet.

2-6
REMOVE DRAIN HOSE
FROM WASHER CABINET
Pull the corrugated drain hose out of the
washer by first grabbing the pull tie. Continue
to pull the hose until the end emerges. Do not
force excess drain hose back into the rear of
the washer.
LAUNDRY TUB DRAIN
OR STANDPIPE DRAIN
Connecting the drain hose form to the cor-
rugated drain hose
To keep drain water from going back into
the washer:
Do not force excess drain hose into stand-
pipe. Hose should be secure but loose
enough to provide a gap for air.
Do not lay excess hose on the bottom of
the laundry tub.
FLOOR DRAIN
Do not install the drain hose form on to the
corrugated drain hose. You may need addi-
tional parts. See Floor drain under “Tools and
Parts.”
•
•
A. Coupling
B. Washer
A B
A B
A
. Feed end of drain hose into one end of form. Secure the lip of the
form into one of the hose ribs.
B. Bend the hose over the top of the form and feed into the other end
of the form, extending it 6-8˝ (15.2 cm - 20.3 cm) beyond the form.
Secure the lip of form into one of the hose ribs.
6 - 8˝
(15.2 cm -
20.3 cm)
CONNECT THE INLET HOSES
1. Insert new flat washers (supplied) into
each end of the inlet hoses. Firmly seat
the washers in the couplings.
CONNECT THE INLET HOSES TO
THE WATER FAUCETS
Make sure the washer basket is empty.
2. Attach the hose labeled hot to the hot
water faucet. Screw on coupling by hand
until it is seated on the washer.
3. Attach the hose labeled cold to the cold
water faucet. Screw on coupling by hand
until it is seated on the washer.
4. Using pliers, tighten the couplings with
an additional two-thirds turn.
NOTE: Do not overtighten or use tape or seal-
ants on the valve. Damage to the valves can
result.
Clear the water lines
Run water through both faucets and inlet
hoses, into a laundry tub, drainpipe or buck-
et, to get rid of particles in the water lines
that might clog the inlet valve screens.
Check the temperature of the water to
make sure that the hot water hose is con-
nected to the hot water faucet and that the
cold water hose is connected to the cold
water faucet.
•
•
Tighten the couplings with an additional two-thirds turn.

2-7
CONNECT THE INLET HOSES
TO THE WASHER
1. Attach the hot water hose to the inlet
valve labeled hot.
2. Attaching one hose coupling first makes
it easier to tighten the connection with pli-
ers.
3. Screw on coupling by hand until it is seat-
ed on the washer.
COLD
HOT
A. Hot water inlet valve
B. Cold water inlet valve
HOTCOLD
AB
4. Using pliers, tighten the coupling with an
additional two-thirds turn.
NOTE: Do not overtighten or use tape or seal-
ants on the valve. Damage to the valves can
result.
Check for leaks
Turn on the water faucets and check for
leaks. A small amount of water might en-
ter the washer. You will drain this in a later
step.
NOTE: Replace inlet hoses after 5 years of
use to reduce the risk of hose failure. Record
hose installation or replacement dates for fu-
ture reference.
If you connect only one water hose, you
must cap off the remaining water inlet
port.
Periodically inspect and replace hoses
if bulges, kinks, cuts, wear, or leaks are
found.
SECURE THE DRAIN HOSE
1. Drape the power cord over the console.
2. Remove any cardboard used to move
washer.
•
•
•
COLD
HOT
5. Attach the cold water hose to the inlet
valve labeled cold.
6. Screw on coupling by hand until it is seat-
ed on the washer.
7. Using pliers, tighten the coupling with an
additional two-thirds turn.
NOTE: Do not overtighten or use tape or seal-
ants on the valve. Damage to the valves can
result.
3. Fasten the drain hose to the laundry tub
leg or drain standpipe with the beaded tie
strap. See view A or B.
Beaded tie strap
If the washer faucets and the drain stand-
pipe are recessed, put the formed end of
the drain hose into the standpipe. Tightly
wrap the tie strap around the water inlet
hoses and the drain hose. See view C.
CBA

2-8
LEVEL THE WASHER
One washer foot has been installed at a dif-
ferent height on the washer. The other three
feet were preset at the factory. Properly level-
ing your washer will minimize noise and vibra-
tion.
1. Slide the washer to its final location.
2. Push on upper front panel to be sure the
washer is on its rear feet.
WARNING
Excessive Weight Hazard
Use two or more people to move and
install washer.
Failure to do so can result in back or
other injury.
4. Check the levelness of the washer by
first placing a level on the lid near the
console. Next, place the level on the side
of the washer in the crease between the
top of the washer and the cabinet.
3. Lower right front foot until it contacts the
floor. By hand, firmly rotate foot as much
as an additional 1-1/2 turns. The other
three feet have been preset at the fac-
tory.
Level the front.
Level the side.
5. If the washer is not level, move the wash-
er out slightly, tip back, prop up the front
of the washer on a wood block. Adjust the
feet up or down as necessary by twisting
the feet. Repeat steps 1 through 4 until
washer is level.
6. Use a 9/16˝ or 14 mm open-end wrench
to turn the locknut counterclockwise on
the foot tightly against the washer cabi-
net.
IMPORTANT: If the locknut is not tight against
the washer cabinet, the washer may vibrate.

2-9
COMPLETE INSTALLATION
1. Check the electrical requirements. Be
sure that you have the correct electrical
supply and the recommended grounding
method. See “Electrical Requirements.”
2. Check that all parts are now installed. If
there is an extra part, go back through the
steps to see which step was skipped.
3. Check that you have all of your tools.
4. Keep the foam packing ring from the
washer tub for future relocation of the
washer. Dispose of or recycle all other
packaging materials.
5. Check that the water faucets are on.
6. Check for leaks around faucets and inlet
hoses.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire, or electrical shock.
WARNING
7. Plug into a grounded 3 prong outlet.
8. Remove any protective film or tape re-
maining on the washer.
9. Read “Washer Use.”
10. To test and to clean your washer, mea-
sure 1/2 of the detergent manufacturer’s
recommended amount of powdered or
liquid detergent for a medium size load
and pour it into the detergent dispenser.
Close the lid. Press POWER. Select a
normal cycle and press Start. Allow it to
complete one whole cycle.

2-10
— NOTES —