Whirlpool 8LIECH-SCDSSFWL User manual

Self-Cleaning
Hot & Cold Hidden Bottled
Water Cooler With Display
Model No.: 8LIECH-SCDSSFWL
SAVE THIS MANUAL FOR
FUTURE USE
USERS’ MANUAL
The appearance of your product may
differ from the above illustration.
For service, call: 1-855-594-4755
or E-mail [email protected]
8LIECH-SCDSSFWL PN 5M009863X115(E+F)

SAFETY PRECAUTIONS ---Electrical Requirements
A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay fuse or
circuit breaker is recommended.
If codes permit and a separate ground wire is used, it is recommended that a qualified
electrician determine that the ground path is adequate.
Check with a qualified electrician if you are not sure whether the water cooler is properly
grounded. The proprietary design of the hot water tank assures availability of hot water and
efficient energy use.
TABLE OF CONTENTS
Safety Precautions-Electrical Requirements ..........................................
Safety Precautions ..........................................................................................
Product Features ............................................................................................
Key Information for Future Use ....................................................................
Specifications ...................................................................................................
Parts & Features ..............................................................................................
Unpacking and Assembly ..............................................................................
Installation .........................................................................................................
Cleaning Prior To Initial Use .........................................................................
Operation ...........................................................................................................
Display’s Operation Explanation ..................................................................
Proper Care & Descaling ................................................................................
Troubleshooting ...............................................................................................
Limited Warranty .............................................................................................
2
3
4
4
5
5
6
6
7
8
11
12
14
16
Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
WARNING
Model # 8LIECH-SCDSSFWL: Page 2
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.

SAFETY PRECAUTIONS
Model # 8LIECH-SCDSSFWL: Page 3
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or other injury when using your water cooler, follow these basic precautions:
■ Plug it into a grounded 3-prong outlet.
■ Do not remove the ground prong.
■ Do not use an adapter.
■ Disconnect power before servicing.
■ Never allow children to dispense hot water without proper supervision. Unplug unit to prevent
unsupervised use by children.
■ All of the parts and panels must be in place before use.
■ Do not use an extension cord.
■ Two or more people should move and install the water cooler
and the bottles.
WARNING
DANGER
All safety instructions will inform you what the potential hazard is, how to reduce the chance of injury, and what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and your appliance. Always read and follow all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER”or “WARNING”
These words mean:
You can be killed or seriously injured if you don′t immediately
follow the instructions.
When operating this dispenser, please observe the following:
• Prior to use, this dispenser must be properly assembled and installed in accordance with
this manual.
• This dispenser is intended to dispense water only. Do NOT use other liquids. Do NOT
use for other purposes. Never use other liquids in the dispenser other than known and
microbiologically safe bottled water. Warranty is void if used with any other liquids,
including but not limited to coffee, tea, juices, beer or wine.
Location Requirements:
• Install the unit in an area where it is protected from the elements, including direct sun.
• Install and use only on a hard, flat and level surface.
• Do NOT place the dispenser inside an enclosed space or cabinet.
• Position the dispenser no closer than 4 inches from the wall. Leave at least 4 inches of
clearance on all sides to permit free airflow.
• Service should only be performed by a certified technician. Please call 1-855--594-4755
for assistance.
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or
other reproductive harm.
The above warnings apply to electrical components within this product only, and not components that come into
contact drinking water.

KEY INFORMATION FOR FUTURE USE
Please register your dispenser immediately at
www.electrotemp.com
Product Self-Cleaning Hot & Cold
Hidden Bottled Water Cooler With Display
Model Number 8LIECH-SCDSSFWL
Serial ID Number
Date of Purchase
For future support, please record your serial number (located on
the label at the back of the dispenser) and purchase date. Staple
your receipt to the manual.
You will need this information to obtain warranty service.
Model # 8LIECH-SCDSSFWL: Page 4
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
PRODUCT FEATURES
Congratulations! You have chosen a technology advanced, state-of-the-art water
cooler.
To provide consistently cold water, this water cooler forms an "Ice Bank" in the cold tank.
Formation of the initial "Ice Bank" can take up to 1 hour.
WHEN THE UNIT IS PLUGGED IN FOR THE FIRST TIME, IT CAN TAKE OVER AN HOUR
BEFORE THE "ICE BANK " FORMS AND THE UNIT CAN PROVIDE THE COLDEST
WATER.

SPECIFICATIONS
PARTS & FEATURES
Power Supply
Refrigerant Type
Cold Water Power
Cold Capacity / Hour
Cold Temperature
Hot Water Power
Hot Capacity / Hour
Hot Temperature
Dimensions
Net Weight
AC 120V / 60Hz / 6.5Amp
R-134A
＜100 Watts
6 Litres / 1.59 Gallon
Factory set at 7°C/45°F/ Adjustable via
display from 4°C/39°F to 13°C/55°F
650 Watts
6 Litres / 1.59 Gallon
Factory set at 85°C/185°F temperature
adjustable via display from 71°C/160°F
to 93°C/199°F temperature will remain
constant
102.8cm H x 32.0cm W x 38.2cm D
40.5inch H x 12.6inch W x 15.0inch D
16.2 Kg / 35.7 Ibs
Model # 8LIECH-SCDSSFWL: Page 5
Front Back
Version 2.0
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
Energy
Verified
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Control: Hot Water
Hot Water Release
Control: Cold Water
Hidden Faucet or tap (hot water)
Hidden Faucet or tap (cold water)
LED Night Lights
Drip Tray
Door
Bottle Tray
Hot Power Switch (Energy Saving)
Cold Power Switch (Energy Saving)
Carry Handle
Drain Plug
Bottle Probe
Door Switch
Water pump
Power Cord
LCD display
Condenser
19
12
13
3
1
2
4
5
7
14
15
16
10
11
18
17
6
8
9
ADJUST

INSTALLATION
Note: Do NOT plug in the power cord until told to do so.
1. Place the dispenser on a hard and level surface in a cool,
shaded location near a grounded wall outlet.
2. Position dispenser so that the back is at least 4 inches from
the wall, and there are at least 4 inches of clearance on
both sides.
3. Level the water cooler as shown below to prevent vibration.
There are two leveling feet at the back of the water cooler.
Please adjust them one at a time until the water cooler sits
levelly and does not rock. Failure to level the water cooler
can cause vibrational noise when the compressor runs.
UNPACKING AND ASSEMBLY
Remove the dispenser from packaging:
1. Lay the box containing the unit on its side.
2. Open bottom flaps of the cardboard box.
3. Stand cooler upright, with box flaps unfolded.
4. Pull box straight up.
5. Unpack the drip tray and insert it into the dispenser.
6. Keep original packing for the duration of warranty.
TO OPEN:
TOP TOP
TOP
TOP
Model # 8LIECH-SCDSSFWL: Page 6
Excessive Weight Hazard
Use two or more people to move and install bottles.
Failure to do so can result in back or other injury.
WARNING
Excessive Weight Hazard
Use two or more people to move and install the
water cooler and the bottles.
Failure to do so can result in back or other injury.
WARNING
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
2 levelling feet

Model # 8LIECH-SCDSSFWL: Page 7
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
To remove any odors or dust that may have accumulated during shipment, you may want
to clean the dispenser prior to first use.
Time Required: 45 minutes.
Note: Do NOT plug in power cord yet.
1. Move the dispenser away from the wall and turn it 90° in either direction.
2. Turn the power switches to OFF.
3. Remove the water bottle and the probe from the water bottle.
4. Place a 2 gallon or larger bucket under the probe assembly.
5. Referring to the figure to the right, take apart the probe assembly parts "A"
and "B", wash the probe parts by hand in soapy water or in the dishwater.
6. Remove the air filter and wash it in soapy water.
7. Submerge the probe hand in the soapy water and rinse properly.
8. Reattach all parts of the probe assembly.
9. Spray the dispensing nozzles of water faucets with chlorine
solution (1 teaspoon of unscented bleach composition
(I.E.5.25% sodium hypochlorite) in a glass of water).
10. Place a 2 gallon or larger bucket under the drain plug in the
rear of the dispenser.
11. Once the unit has been drained, replace the drain plug and
drain the cap.
12. Remove remaining water from the reservoirs by dispensing it
from the cold tap into a pitcher.
Pre-Rinsing the Water System
13. Fill bottle with 2 gallons of tap water.
14. Insert probe assembly, place bottle into water cooler and
close the door.
15. Allow cooler to be filled with water.
16. Drain water out as in steps 10, 11 and 12 of "Cleaning Prior To Initial Use" section.
17. If chlorine taste persists, repeat rinsing procedure.
18. Complete the installation and follow the operation instructions indicated in this manual. If your
water has an off-taste, do not return the dispenser to the store. Call 1-855-594-4755 for
assistance.
CLEANING PRIOR TO INITIAL USE
A
B

OPERATION
The unit’s self-cleaning feature prevents formation of Biofilm. The self-cleaning feature is
not intended for water purification.
This unit is intended for use with high-quality bacteriologically safe bottled water only. Do
NOT use other liquids. Do NOT use for other purposes. Warranty is void if unit is used with
any other liquids, including tap water, coffee, tea, juices, beer, or wine.
This dispenser has been designed to use with standard water bottles with a 3, 5, or 5.2
gallon capacity. Do NOT use alternative bottles.
Initial Set Up
Do NOT plug in until steps 1-3 are completed.
1. If unit was transported on its side, make sure unit is in the OFF position
and is upright for at least 4 hours prior to plugging the unit in.
2. This model uses a pump to deliver water from the bottle to the reservoirs:
i. Clean the bottle cap and neck.
ii. Remove the entire plastic cap from the bottle.
iii. Adjust the length of the probe by pulling the B portion of the tube to its
maximum extension. Insert the probe into the bottle and push it down.
The probe will self-adjust to its appropriate length. (See illustration on
right).
iv. Push down the probe head until it is seated.
v. Plug power cord into the wall outlet.
Note: At initial start-up, it will take less than 3 minutes to fill reservoirs with
water. If pump stops prematurely, please open and close the door to
activate reset using door switch.
IMPORTANT
Model # 8LIECH-SCDSSFWL: Page 8
Excessive Weight Hazard
Use two or more people to move and install the
water cooler and the bottles.
Failure to do so can result in back or other injury.
WARNING
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
A
B
Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
WARNING

Note: When using a 5 gallon rectangular bottle, slide it into place as shown in the illustration below.
• If the probe tube A and B are not sealed (see previous page), the pump will run a few minutes
and the night lights will flash. To correct, open the door, re-attach the probe, and close the
door.
• If the lights continue to flash, your bottle may be empty or there may be an issue with the water
tube lines. Call 1-855-594-4755 for assistance.
3. Turn the switches at the back of the dispenser to ON.
• The red switch controls the hot water. If you do not want hot water, leave hot water switched
OFF.
• The blue switch controls the cold water. If you do not want cold water, leave this switched OFF.
• For the unit to operate properly, the probe head must seal on the bottle and the door must be
fully closed.
• It will take less than 3 minutes to fill reservoirs with water. During this time, it is normal for the
pump to run on and off.
• If water fill stops before reservoirs are full, please open and close the door to reset door acti-
vated switch.
• Each time you dispense water from the taps, the pump will turn on to refill the tanks.
• Self-cleaning works every 4 hours for short time. Self-cleaning pump sound is normal.
Dispensing Cold Water
Note: After setup, it will take up to 1 hour to get the water to its coldest temperature. During this
time, the compressor may run continuously as the refrigeration system builds the Ice Bank as
noted in the "Product Features" section.
1. Position the container you wish to fill with water securely below the cold-water tap.
• The right triangle below the cold water control indicates the location of the cold water tap
(See the "Parts & Features" section on page 5).
Model # 8LIECH-SCDSSFWL: Page 9
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.

• The circular shapes in the drip plate help to align the flow of water. This unit dispenses
water quickly. To avoid splashes, hold the cup as close to the tap as possible.
2. Press the right control downward to start dispensing water.
3. Release the control once desired fill level is achieved.
Dispensing Hot Water
Note: After setup, hot water will be available in 15-20 minutes.
The Energy Saver Feature keeps hot water on standby at 80°C/176°F. Automatic Extra
Hot Booster is activated when 3 oz of water is drawn. Extra Hot water stays for at 90°C/194°F
for 2 hours before returning to Energy Saver mode.
1. Position the container you wish to fill with water securely below the hot-water tap.
• The left triangle below the hot water control indicates the location of the hot
water tap (See the "Parts & Features" section on page 5).
• The circular shapes in the drip plate help align the flow of water. To avoid splashes,
hold the cup as close to the tap as possible.
2. Push the hot water release button (red) inward and press the control downward to start
dispensing water.
3. Release the control once desired fill level is achieved.
Replacing an Empty Bottle
Note: When your water bottle is empty, the dispenser will be intermittently and the LED night
lights will blink until a fresh bottle is connected.
You may also hear a sucking sound when the bottle is empty and needs changing. This is
normal and is another way to be alerted that your bottle is empty and needs to be replaced.
Replace the bottle as soon as you notice that it is empty. If a new bottle is unavailable, leave
the door ajar or unplug the cooler to stop the beeping noise and flashing lights.
1. Open the door and slide the bottle out.
2. Remove the probe by pulling it straight up until it is completely out of the bottle.
3. To install fresh bottle:
• Place the fresh bottle in front of the tray.
• Clean the fresh bottle using a soft cloth and warm soapy water.
• Remove the entire plastic cap from the top of the bottle.
• Insert the probe into the bottle.
• Push the probe down until it is sealed.
• Slide the bottle onto the tray and close the door completely.
Model # 8LIECH-SCDSSFWL: Page 10
Excessive Weight Hazard
Use two or more people to move and install bottles.
Failure to do so can result in back or other injury.
WARNING
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.

DISPLAY’S OPERATION EXPLANATION
Model # 8LIECH-SCDSSFWL: Page 11
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
Cold and Hot water symbols will flash when heating and cooling are working.
The unit’s display shows the current temperature of the chilled and heated water. It also
allows for temperature customization of both cold and hot water.
Adjusting temperature:
- Hold SET button until hot temperature display starts flashing.
- Touch to adjust temperature incrementally.
- Touch SET to save
- Do the same for cold-water temperature.
Temperature Range:
- Hot from 71°C/160°F to 93°C/199°F
- Cold from 4°C/39°F to 13°C/55°F
Choosing Temperature scale:
- Factory default settings are Fahrenheit.
- Press SET button until °C or °F icon flashes.
- Switch between °C and °F by touching adjust button.
- Touch SET to save.
Energy Star settings:
- Energy Star compliant default settings are factory set.
- By setting your desired temperatures you may exit the default Energy Star settings.
- To return to factory default settings unplug then re-plug power cord to reset Energy Star settings.
- By choosing the maximum cold and the maximum hot water settings you may increase power
consumption by up to 200 Watts per day.
Optimum Settings:
For optimum performance set cold water at 5.5°C/42°F and hot water at 90°C/194°F.
Self-cleaning function
- The cleaning function activates every 4 hours automatically.
Night Lights On/Off function
- To turn On/Off LED Night Lights please hold ADJUST button for 3 seconds
SELF CLEANING
C
C
SET ADJUST
SELF CLEANING
C
C

General Cleaning
Perform: As needed
Time Required: 5 minutes.
Note: Do NOT use abrasive materials or chemical cleaners.
1. Clean cabinet surfaces with a soft cloth and warm soapy water.
2. Wipe dust from back of dispenser to improve the unit’s efficiency.
3. Remove the drip tray assembly by sliding it forward. Remove the cover. Wash both tray and
cover in a dishwasher or wipe parts clean with a soft cloth and warm soapy water.
4. Reattach drip tray assembly.
Descaling
If you use mineral water you will need to descale your hot water tank.
Heated mineral water will cause minerals to fall out. Eventually they will plug up your waterways,
resulting in a gradual slowdown of the flow rate, leaking faucets, and other problems.
Descaling Solutions
Cooking vinegar is proven to remove calcium deposits efficiently.
Depending on the frequency of decalcification treatments, please use the following proportions of
White Vinegar.
- For descaling once every 3 months, use 2 cups (500 ml) of white vinegar with 2.5 liters of hot
water.
- For descaling once every 6 months, use a mixture of 6 cups of white vinegar with 2 liters of hot
water.
- For descaling once every year, use 12 cups of white vinegar and 1 liter of hot water.
- For descaling less frequently than once a year, use undiluted white vinegar.
Descaling Procedure
1. Fill a bucket or empty 5-gallon water bottle with the vinegar solution of your choice. For propor-
tions, refer to the instructions above. Choose quantity in accordance with the frequency of your
treatments.
Model # 8LIECH-SCDSSFWL: Page 12
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.
PROPER CARE & DESCALING

2. Attach or insert the probe to the bucket/bottle.
3. Place the bucket/bottle into the cooler and close the door. The water will be pumped up into the
holding tanks.
4. Plug in the cooler and turn on the hot switch located at the back of the cooler. Do not turn on the
cold-water switch.
5. Wait for 1 hour.
6. Unplug the cooler from the wall
7. Using rear drain plug, drain the water from the cooler into a bucket and discard the water.
A. Locate the white plastic cap at the back of the cooler.
B. Remove the screw.
C. Remove the clear silicone drain plug and allow water to drain out.
D. Reattach the drain plug and plastic cap before proceeding.
8. Fill the bucket/bottle with tap water and place into the machine.
9. Plug the cooler back into the wall, close the door and wait for 10 minutes.
10. Dispense water from both cold and hot faucets until smell from cleaning substances disappears.
11. Open drain plug and cap once again and drain all tap water.
12. Replace the drain plug and cap.
13. Place a fresh bottle of water into the machine and operate as usual.
14. This procedure must be repeated every 3 to 6 months, depending on mineral content and usage
of water cooler.
Model # 8LIECH-SCDSSFWL: Page 13
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.

TROUBLESHOOTING
Excessive Weight Hazard
Use two or more people to move and install bottles.
Failure to do so can result in back or other injury.
WARNING
Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
WARNING
Call 1-855-594-4755 for service.
Problem: Stainless steel surfaces are smudgy or fingerprinted.
Solution: Use paper towel to wipe excess oils until surface feels dry to the touch.
• To maintain beauty of stainless steel, oil it periodically using a stainless steel cleaning
solution available at hardware stores, or use mineral oil (unscented baby oil).
Problem: The buttons for dispensing water are slow-moving or jammed.
Solution: Dust and cooking oils might cause slow moving push buttons. Add mineral oil (unscented
baby oil) between the gaps of buttons to clear dirt.
Problem: Dispenser is not operating.
Solution: Make sure that the power cord is properly connected to a working outlet.
Problem: Water is leaking.
Solution: Replace water bottle. The most common cause of this issue is a cracked bottle. If the
leak remains, unplug unit and call 1-855-594-4755 for assistance.
Model # 8LIECH-SCDSSFWL: Page 14
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.

Problem: Buttons are stuck.
Solution: Apply mineral oil (unscented baby oil) to the button slides to reduce friction.
Problem: No water is coming from the taps.
Solution: Make sure the water bottle is not empty. If it is, replace it. If not, adjust the probe to an
appropriate length.
• Make sure that you fully press the water controls.
• Make sure that the probe connection with the water bottle forms a complete seal.
• Make sure that the door is closed.
Problem: Water dispensed is not cold.
Solution: Note that it takes up to 1 hour after setup to dispense cold water.
• Make sure that the back of the dispenser is at least 4 inches from a wall and that air is
free to flow on all 4 sides of the dispenser.
• Make sure that the cold-water switch is ON.
Problem: Water dispensed is not hot.
Solution: Note that it takes 15-20 minutes after setup to dispense hot water.
• Make sure that the power cord is properly connected to a working outlet.
• Make sure that the hot water switch is ON.
Problem: LED night lights are flashing and the dispenser is making beeping noises.
Solution: Replace the empty bottle. If you cannot replace the empty bottle immediately, leave the
door ajar or unplug the cooler to stop the beeping noise and the flashing lights.
Problem: The dispenser is noisy.
Solution: Make sure the cooler is properly levelled using the two adjustable feet at the back of the
unit.
Problem: Pump is not pumping water into cooler.
Solution: Make sure that tubing is properly inserted into quick connectors on the pump.
Problem: Does the night light in the front of the cooler stay on?
Solution: To turn On/Off LED Night Lights please hold ADJUST button for 3 seconds.
Model # 8LIECH-SCDSSFWL: Page 15
IMPORTANT: Do NOT Return Dispenser To Store.
If you have a question or problem, please contact 1-855-594-4755 for assistance.

LIMITED WARRANTY
Electrotemp Technologies Inc., (“Vendor”) warrants to the original purchaser of this dispenser, and to no
other person, that if this dispenser is assembled and operated in accordance with the printed instructions
accompanying it, then for a period of one (1) year from the date of purchase, all parts in such dispenser
shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date
of purchase from an authorized retailer or distributor. Therefore, you should retain your sales slip or
invoice. The Limited Warranty shall be limited to repair or replacement of parts, which prove defective
under normal use and service and which Vendor shall determine in its reasonable discretion upon exami-
nation to be defective. Before returning any parts, you should contact Vendor’s Customer Service Depart-
ment using the contact information listed below. If Vendor confirms, after examination, a defect covered by
this Limited Warranty in any returned part, and if Vendor approves claim, Vendor will replace such defec-
tive part without charge. If you return defective parts, transportation charges must be prepaid by you.
Vendor will return replacement parts to original purchaser, freight or postage prepaid.
The Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse,
alteration, misapplication, improper installation or improper maintenance or service by you or any third
party, or failure to perform normal and routine maintenance on the dispenser, as set out in the User’s
Manual. In addition, the Limited Warranty does not cover damages to the finish, such as scratches, dents,
discoloration or rust after purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for products
that are purchased from seller other than authorized retailers or distributors. AFTER THE PERIOD OF
THE ONE (1) YEAR EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRAN-
TIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR SHALL HAVE NO LIABILITY WHAT-
SOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCI-
DENTAL, OR CONSEQUENTAL DAMAGES. Vendor assumes no responsibility for any defects caused by
third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow exclusion or limitation of
special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above
exclusion and limitations may
not apply to you.
Warranty is void if the electrical outlet is improperly wired to incorrectly sized circuit breaker or fuse,
if not grounded properly, or wires do not have correct polarity.
Use of this cooler confirms Purchasers agreement with the conditions of this warranty.
Electrotemp Technologies Inc.
406 Watline Avenue
Mississauga, Ontario, L4Z-1X2
1-844-926-6537
www.electrotemp.com
Model # 8LIECH-SCDSSFWL: Page 16
®/TM ©2016 Whirlpool. All rights reserved.
Manufactured under license by Electrotemp Technologies Inc., Mississauga, ON. Canada
Limited warranty provided by manufacturer.
REV. 2016-04-29

名称：说明书8LIECH-SCDSSFWL(加拿大沃尔玛）-English
图号：5M009863X115(E+F)
修订 修改内容
按客户要求修改 李雪玲 2013－08-30
日期修改人
修订表
A
1.再次按客户和老板要求修改
2. 大部分页面都有修改
3. 删掉16 17 18页 李雪玲 2013－09-11
B
1.再次按客户要求修改第2页，5页，第12页，17页
2.超重警告标贴和电气警告标贴字体和大小有调整
3.增加不锈钢清洗
李雪玲 2013－10-11
03
第5页 部件图4 由cold water更改为hot water，
部件图5 由hot water更改为cold water 李雪玲 2013－11-01
04
李雪玲 2014-04-10
05
1. 第5页Cold Temperature 改为4°C/50°F 和Hot Temperature 改
为90°C/194°F, 热水出水量由4 Litres/1.06 Gallon更改为 8
Litres/2.11 Gallon, 热胆功率由425 Watts 变更为870 Watts
2. 第17页增加 “ if your pump is not pumping water into......”及图
3. 电流由5A更改为8A，节能之星，产品图，最后一页惠而浦信息有修改.
4. 按惠而浦要求修改每页
李雪玲 2014-05-20
06
1. 第1页，5页，6页，8页，9页，10页，18页饮水导杆变回原来不加套
2. 第2页增 加电子温控说明 3. 惠而浦要求修改他们的地址
4. Electrotemp 服务电话由888-828-1426变更为1-844-926-6537
5. 第6页部件图下 增加一句电子节能说明
李雪玲 2014-06-18
07
08
1. 第1页，5页，6页，8页，9页，10页，15页，17页饮水导杆变为新二代
2. 第2页电子温控说明有修改并移到第4页，电气由第3, 4页移至第2, 3页
3. 第5页净重位置调整，与铭牌一致 4. 第18页水泵带快速接头图有修改
李雪玲 2014-10-15
李雪玲 2014-12-19
09
10
11
12
1. 第1页，5页，6页，10页接近开关改为门开关
李雪玲 2015-02-06
李雪玲
2015-03-30
2015-04-01
2015-04-08
2015-04-09
2015-04-17
1. 惠而浦服务电话由1-844-494-4757变更为1-855-594-4755
李雪玲 2014-09-04
1. 第2页增加“拆开面板，无保修” 2. 图号上加（E+F）
3. 第5页电流由8A变更为AC 120V / 60Hz/8Amp, 冷水温度由4°C/39.2°F
变更为5°C/41°F, 产品尺寸位置 由38.2 D x 32.0 W x 102.8 H (cm)/15.0
D x 12.6 W x 40.5 H (inch)变更为32.0 W x 38.2 D x 102.8 H (cm)/12.6
W x 15.0 D x 40.5 H (inch)，与铭牌 和其他款统一，增加测试说明
4. 首页增加“The appearance of your product maydiffer from the above illustration.
最后一页法律声明部分，在warranty之前加上limited 更新为2015
第2页增加一条安全警告语
1. 封面，第4页，第7页，第8页，换成狗腿饮水杆，
1. 第10页，第16页冷水最冷时间由6小时变更为1.5小时，2. 故障排除部分
增加2点问题解决
1. 热胆功率由870W变更为650W， 2. 热水出水量由8升变更为6升，
3. 电流由8A变更为6.5A
删掉原第4页超级节能说明，目录页码重新编，第3页冷水最冷时间由6小时变更为
1小时，第10页，第16页冷水最冷时间由1.5小时变更为1小时
封面加售后邮箱

1、第6页安装部分删除第3点, 增加BL底脚安装说明，第15页嗓音部分修改
2、第9页加一句夜灯开关说明 “The yellow switch controls the LED night lights. Turn it ON or OFF as desired.”
第15页TROUBLESHOOTING部分增加最后一个问题点
设计： 工程审核： 业务审核：
品质审核： 批准：
修订 修改内容 日期 修改人
修订表
技术要求：
1、尺寸：215x279 毫米。
2、单色印刷。
3、产品符合必须符合美国加州环保CA65和ROHS要求，并提供有效的相关测试报告。
4、批量生产前一定要样品确认，不得擅自更改图纸。
5、已经根据DRC-包材设计可靠性检查表核对过。
13
14
15
1 P5 删除 specifications下面那段内容,删除non-adjustable
2 调整note 字体
3 p6 installation 第一段 in a cold shade改为cool and
shady;
4.P8中IMPORTANT INITIAL SET UP 字体大小更改；
5.p11 -12 改为PROPER CARE & DESCALING, 后面的
内容改为从general cleaning to taset or smell; p12 增加
Water cooler is quiet while on standby mode:
这段内容；sanitizing 这段内容更改；Step A改为 how to
drain water
6. 删除p13，14，18
7.p17中删除 water tastes bad整段；Dispenser is noisy
增加内容 use materovided ....
8 目录相应页码更改。大变更
肖祥丽
2015-6-6
李雪玲
李雪玲
2015-10-29
2015-12-30
第12页，第13页清洗热胆部分更新
铝线压缩机，净重由16.4 kg / 36.2 lbs变更为16.2 kg / 35.7 lbs
李雪玲
李雪玲
第5页部件图增加第12个夜灯开关 2016-02-26
2016-04-25
李雪玲 2016-04-29
去掉第5页部件图增加第12个夜灯开关和第9页加一句夜灯开关说明
“The yellow switch controls the LED night lights. Turn it ON or OFF as desired.”
第11页最后增加怎么样操作夜灯开关并且第15页故障部分最后一个问题点回答也按这个改了