Whispbar K619W Operation and installation manual

K619W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema
de transporte
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de
transporte.
RU Установочные Инструкции для
Поперечных Балок
x 1 x 1 x 2 x 4
x 4 x 4
Revision No: 6F 1

Fitting Kit K619W
MAX kgs (lbs)
W/P WHD
Opel
Agila, 5dr Hatch 08-15 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Agila, 5dr Hatch 08-15 CN 50 kgs (110 lbs) 50 kgs (110 lbs)
Vauxhall
Agila, 5dr Hatch 08-15 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Suzuki
Splash, 5dr Hatch 08-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Splash, 5dr Hatch 08-+ CN 50 kgs (110 lbs) 50 kgs (110 lbs)
Splash, 5dr Hatch 11-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit K619W
X
A B C 1 2 3
Agila, 5dr Hatch 08-15 (EU) -150mm 470mm - 765mm 745mm -
-5 -7/8ths" 18 1/2ths" - 30 1/8ths" 29 5/16ths" -
Agila, 5dr Hatch 08-15 (CN) -150mm 470mm - 765mm 745mm -
-5 -7/8ths" 18 1/2ths" - 30 1/8ths" 29 5/16ths" -
Agila, 5dr Hatch 08-15 (EU) -150mm 470mm - 765mm 745mm -
-5 -7/8ths" 18 1/2ths" - 30 1/8ths" 29 5/16ths" -
Splash, 5dr Hatch 08-+ (EU) -150mm 470mm - 765mm 745mm -
-5 -7/8ths" 18 1/2ths" - 30 1/8ths" 29 5/16ths" -
Splash, 5dr Hatch 08-+ (CN) -150mm 470mm - 765mm 745mm -
-5 -7/8ths" 18 1/2ths" - 30 1/8ths" 29 5/16ths" -
Splash, 5dr Hatch 11-+ (NZ) -150mm 470mm - 765mm 745mm -
-5 -7/8ths" 18 1/2ths" - 30 1/8ths" 29 5/16ths" -
3

Fitting Kit EN
K619W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K619W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K619W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6

Fitting Kit EN
K619W
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-250
B = 11-04-251
C = 11-04-292
7

Fitting Kit EN
K619W
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
8

Fitting Kit EN
K619W
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
9

Fitting Kit EN
K619W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10