Whispbar K694W User manual

K694W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 1 x 4 x 4
x 2 x 2 x 4 x 1
Revision No: 5E 1

Fitting Kit K694W
MAX kgs (lbs)
W/P WHD
Mazda
2 , 5dr Hatch 15-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2 , 5dr Hatch 15-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
2 , 5dr Hatch 15-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
3 , 4dr Sedan 14-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
3 , 4dr Sedan 14-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
3 , 4dr Sedan 14-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
3 , 4dr Sedan 14-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
6 , 4dr Sedan 12-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
6 , 4dr Sedan 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
6 , 4dr Sedan 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
6 , 4dr Sedan 12-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit EN
K694W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3

Fitting Kit EN
K694W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
4

Fitting Kit EN
K694W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
5

Fitting Kit EN
K694W
Fitment
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Mark a reference point for the front and
rear mounting points with a pen as shown.
●Use drill bit supplied, to drill holes in
marked positions.
6

Fitting Kit EN
K694W
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Refer to the underside of the pad for the
part number.
7

Fitting Kit EN
K694W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 295A
B = 296A
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
8

Fitting Kit EN
K694W
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
●If crossbars are removed, please install the
rubber plugs into the ditch moulding.
9

Fitting Kit EN
K694W
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10