Whispbar K716W User manual

K716W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema
de transporte
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de
transporte.
RU Установочные Инструкции для
Поперечных Балок
x 1 x 1 x 1 x 1
x 2 x 1 x 1 x 2
x 2 x 2 x 1 x 1
Revision No: 1A 1

Fitting Kit K716W
MAX kgs (lbs)
W/P WHD
Toyota
Rav 4 , 5dr SUV Jan 13-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Rav 4 , 5dr SUV Jan 13-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Rav 4 , 5dr SUV Jan 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Rav 4 , 5dr SUV Jan 13-+ US 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit EN
K716W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3

Fitting Kit EN
K716W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the rear of this manual for
information relating specifically to your
vehicle.
4

Fitting Kit EN
K716W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
5

Fitting Kit EN
K716W
Fitment
●Open or remove fixed-point covers.
●Store items away in a safe place.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 239A
B = 241A
●Hook clamps into the fixed points on the
vehicle.
6

Fitting Kit EN
K716W
●Place ditch mould insert over the clamp.
●Repeat at other end.
●Refer to the underside of the pad for the
part number.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 296
B = 297
7

Fitting Kit EN
K716W
●Place pads on roof as per diagram. Screw
thread should be vertically through square
hole in pad.
●Place crossbar foot over clamp bolt.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
8

Fitting Kit EN
K716W
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat at other end.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
●Use keys to remove covers.
9

Fitting Kit EN
K716W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Remove locking screw.
10