Whispbar K722W User manual

K722W
Fitting Kit
EN Fitting Instructions for Basic Carrier
PL Instrukcja systemu montażu
x 2 x 2 x 2 x 2
x 4 x 4
Revision No: 5E 1

Fitting Kit K722W
MAX kgs (lbs)
W/P WHD
Opel
Adam, 3dr Hatch 13-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Astra GTC, 3dr Hatch 11-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra GTC, 3dr Hatch 11-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra GTC, 3dr Hatch 11-14 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra GTC, 3dr Hatch 12-14 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 5dr Hatch 10-13 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 5dr Hatch 10-15 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 5dr Hatch 10-15 ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Zafira Tourer, 5dr MPV 12-Sep 16 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Zafira ZJ, 5dr MPV 12-13 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Zafira, 5dr MPV 12-Jan 15 CN 75 kgs (165 lbs) 75 kgs (165 lbs)
Zafira, 5dr MPV Oct 16-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Vauxhall
Adam, 3dr Hatch 13-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Astra GTC, 3dr Hatch 11-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 5dr Hatch 10-15 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Zafira Tourer, 5dr MPV 12-Sep 16 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Zafira, 5dr MPV Oct 16-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Holden
Astra, 3dr Hatch 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 3dr Hatch 15-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K722W
X
A B C 1 2 3
Adam, 3dr Hatch 13-+ (EU) -460mm 200mm - 805mm 705mm -
-18 -1/8ths" 7 7/8ths" - 31 11/16ths" 27 3/4ths" -
Adam, 3dr Hatch 13-+ (EU) -460mm 200mm - 805mm 705mm -
-18 -1/8ths" 7 7/8ths" - 31 11/16ths" 27 3/4ths" -
Astra GTC, 3dr Hatch 11-+ (EU) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra GTC, 3dr Hatch 11-+ (ZA) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra GTC, 3dr Hatch 11-+ (EU) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra GTC, 3dr Hatch 11-14 (CN) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra GTC, 3dr Hatch 12-14 (AU) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra, 3dr Hatch 15-+ (AU) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra, 3dr Hatch 15-+ (NZ) -360mm 325mm - 775mm 695mm -
-14 -3/16ths" 12 13/16ths" - 30 1/2ths" 27 3/8ths" -
Astra, 5dr Hatch 10-13 (AU) -190mm 485mm - 790mm 745mm -
-7 -1/2ths" 19 1/8ths" - 31 1/8ths" 29 5/16ths" -
Astra, 5dr Hatch 10-15 (EU) -190mm 485mm - 790mm 745mm -
-7 -1/2ths" 19 1/8ths" - 31 1/8ths" 29 5/16ths" -
Astra, 5dr Hatch 10-15 (ZA) -190mm 485mm - 790mm 745mm -
-7 -1/2ths" 19 1/8ths" - 31 1/8ths" 29 5/16ths" -
Astra, 5dr Hatch 10-15 (EU) -190mm 485mm - 790mm 745mm -
-7 -1/2ths" 19 1/8ths" - 31 1/8ths" 29 5/16ths" -
Zafira Tourer, 5dr MPV 12-Sep 16 (EU) 100mm 800mm - 880mm 845mm -
3 15/16ths" 31 1/2ths" - 34 5/8ths" 33 1/4ths" -
Zafira Tourer, 5dr MPV 12-Sep 16 (EU) 100mm 800mm - 880mm 845mm -
3 15/16ths" 31 1/2ths" - 34 5/8ths" 33 1/4ths" -
3

Fitting Kit K722W
Zafira ZJ, 5dr MPV 12-13 (AU) 100mm 800mm - 880mm 845mm -
3 15/16ths" 31 1/2ths" - 34 5/8ths" 33 1/4ths" -
Zafira, 5dr MPV 12-Jan 15 (CN) 100mm 800mm - 880mm 845mm -
3 15/16ths" 31 1/2ths" - 34 5/8ths" 33 1/4ths" -
Zafira, 5dr MPV Oct 16-+ (EU) 110mm 815mm - 862mm 830mm -
4 5/16ths" 32 1/16ths" - 33 15/16ths" 32 11/16ths" -
Zafira, 5dr MPV Oct 16-+ (EU) 110mm 815mm - 862mm 830mm -
4 5/16ths" 32 1/16ths" - 33 15/16ths" 32 11/16ths" -
4

Fitting Kit EN
K722W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
5

Fitting Kit EN
K722W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
6

Fitting Kit EN
K722W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
7

Fitting Kit EN
K722W
Fitment
●Open or remove fixed-point covers.
●Locate fixed clamping block A
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 096A
B = 095A
●Hook small claw into rear of the clamping
block
●Hook large claw into front of the clamping
block
8

Fitting Kit EN
K722W
●Refer to the underside of the pad for the
part number.
●Letters refer to the pad part numbers and
position.
●It is important to put the pads in the correct
position on the vehicle.
●Pad Part Number:
A = 267A
B = 268A
●Ensure internal clamp sits upright.
●Fit pad carefully over fixed point and clamp
screw.
9

Fitting Kit EN
K722W
●Mount crossbars over clamps.
●Repeat for all legs.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
10

Fitting Kit EN
K722W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
11

Fitting Kit EN
K722W
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
12

Fitting Kit EN
K722W
●Check and replace worn out or defective
parts.
●Keep the product clean and maintained.
●Never drive into a car wash with the roof
rack system fitted.
●Lubricate locks and adjusting screws at
regular intervals.
●Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
●Yakima Europe Coöperatief U.A.
Archimedesbaan 25
3439 ME Nieuwegein
The Netherlands
[phone]
www.whispbar.eu
www.whispbar.co.uk
●Yakima Products, Inc.
4101 Kruse Way,
Lake Oswego, OR 97035
USA
www.whispbar.com
www.whispbar.ca
13

Fitting Kit PL
K722W
Pierwszy montaż
●Sprawdź zawartość opakowania i upewnij
się, czy zawiera wszystkie części
znajdujące się na liście. Jeśli nie,
skontaktuj się z odpowiednim sklepem.
●Kit pasuje do belek typu A, B, C oraz D.
●Instrukcja opisuje sposób montażu belek
typu A. Może być również stosowana do
belek typu B, C i D.
●Odkręć osłony za pomocą klucza.
14

Fitting Kit PL
K722W
●Zdejmij osłony za pomocą klucza.
●Przyciśnij i usuń blokadę. Zamontuj stopy.
●Sprawdź czy oba końce belek mają taką
samą długość.
●Wyreguluj belki na długość (odnoszą się do
tyłu niniejszej instrukcji)
●Czytać na z przodu instrukcji znajdziesz
specyfikacje dla twojego samochodu.
15

Fitting Kit PL
K722W
●Dokręć z siłą 5 Nm / 3.7 ft lb.
●Zdjąć blok zacisku z tworzywa sztucznego
chwytając stopę poprzeczki palcami i
mocno docisnąć kciukami aż blok
zaciskowy wysunie się za stopę.
●Usuń wewnętrzną blokadę i umieść ją w
stopie.
●Powtórz czynność dla reszty stóp.
16

Fitting Kit PL
K722W
Montaż
●Åpne eller fjern dekselet på fix point festet.
●Umieść łapkę w elemencie A.
●Bardzo ważne jest aby umieścić łapy w
odpowiednich miejscach na dachu
samochodu
●Litery odnoszą się do oznakowań na
łapkach
●Numer łapy:
A = 096A
B = 095A
●Małe łapki zamontuj z tyłu.
●Duże łapki zamontuj z przodu.
17

Fitting Kit PL
K722W
●Zobacz numer pod spodem łapki.
●Litery oznaczają podkładki oraz sposób ich
rozmieszczenia.
●Bardzo ważne jest aby umieścić podkładek
w odpowiednich miejscach na dachu
samochodu
●Rozmieszczenie podkładek:
A = 267A
B = 268A
●Upewnij się, że łapa została poprawnie
zamontowana.
●Umieść podkładki nad punktami
montażowymi. Dokręć śruby.
18

Fitting Kit PL
K722W
●Zamocuj belki nad łapkami.
●Powtórz czynność dla reszty stóp.
●Skręć motylkiem. Ułóż motylek równolegle
do dachu samochodu.
●Sprawdź czy motylek znajduje się w pozycji
jak na rysunku.
●Powtórz czynność w czterech miejscach.
19

Fitting Kit PL
K722W
●Upewnij się, czy belka została poprawnie
zamontowana
●Zamknij osłony za pomocą klucza.
UWAGA: Sprawdź czy dokładnie dokręciłeś śruby
20