Whispbar K880W User manual

K880W
Fitting Kit
EN Fitting Instructions for Basic Carrier CAUTION: Professional
installation recommended
x 2 x 2 x 4 x 2
x 6 x 1 x 6 x 6
x 1 x 12 x 12 x 6
Revision No: 3C 1

Fitting Kit K880W
MAX kgs (lbs)
W/P WHD
Isuzu
MU-X, 5dr SUV 14-+ NZ
MU-X, 5dr SUV Dec 13-+ AU
75 kgs (165 lbs) 75 kgs (165 lbs)
75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K880W
X
A B C 1 2 3
MU-X, 5dr SUV 14-+ (NZ) - 700mm 1400mm 960mm 927mm 905mm
- 27 9/16ths" 55 1/8ths" 37 13/16ths" 36 1/2ths" 35 5/8ths"
MU-X, 5dr SUV Dec 13-+ (AU) - 700mm 1400mm 960mm 927mm 905mm
- 27 9/16ths" 55 1/8ths" 37 13/16ths" 36 1/2ths" 35 5/8ths"
3

Fitting Kit EN
K880W
Items you will require:
●Tape measure
Pen
Flat-head screwdriver
Craft knife
Side cutters or tin snips
Hammer
8mm (3/8") punch
Cordless drill
Depth stop
Vacuum cleaner
Rust inhibitor
Small paint brush
Neutral cure silicon sealant
Rivet gun
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
4

Fitting Kit EN
K880W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
5

Fitting Kit EN
K880W
●Note: 2 Bar System
●Note: 3 Bar System
●Attention:
●Permanent Mount Fitment
●Position as shown.
6

Fitting Kit EN
K880W
●Carefully select desired position for
crossbars on vehicle roof.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Apply masking tape to vehicle roof in all
four positions.
●Make sure there is no interference between
what you intend to carry with aerials,
sunroof or tailgate.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Trace around rubber pad using a pencil or
pen.
●Repeat for all four positions.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
●Repeat for all legs.
7

Fitting Kit EN
K880W
●While holding foot, detach crossbar from
foot.
●Drill through the two holes in the foot while
holding foot tight on roof in marked
position.
●Remove masking tape and place silicon
sealant around drilled holes on roof for all
four positions.
8

Fitting Kit EN
K880W
●Install rivets through permanent mount
blocks.
WARNING: Do not use countersunk screws as an
alternative fixing method to the rivets supplied with
this kit.
●While holding the permanent mount block
firmly on roof, rivet the blocks to the roof.
9

Fitting Kit EN
K880W
●Note: 2 Bar System
●Repeat for all four positions.
●Note: 3 Bar System
●Repeat for all six positions.
●Fit plastic plugs to permanent mount blocks
over rivet heads.
●Assemble as shown.
10