Whispbar K751W User manual

K751W
Fitting Kit
EN Fitting Instructions for Basic Carrier
DMontageanleitung für Basisträgersystem
ES Instrucciones de montaje para el sistema
de transporte
FInstructions de montage pour Basic Carrier
NO Monteringsanvisning for takstativ
PT Instruções de Montagem para sistema de
transporte.
RU Установочные Инструкции для
Поперечных Балок
x 2 x 2 x 4 x 4
x 1 x 1 x 1 x 1
Revision No: 2B 1

Fitting Kit K751W
MAX kgs (lbs)
W/P WHD
Opel
Astra, 4dr Sedan 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Astra, 4dr Sedan 13-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
New Astra, 4dr Sedan 13-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K751W
X
A B C 1 2 3
Astra, 4dr Sedan 13-+ (EU) -175mm 525mm - 795mm 760mm -
-6 -7/8ths" 20 11/16ths" - 31 5/16ths" 29 15/16ths" -
Astra, 4dr Sedan 13-+ (EU) -175mm 525mm - 795mm 760mm -
-6 -7/8ths" 20 11/16ths" - 31 5/16ths" 29 15/16ths" -
New Astra, 4dr Sedan 13-+ (ZA) -175mm 525mm - 795mm 760mm -
-6 -7/8ths" 20 11/16ths" - 31 5/16ths" 29 15/16ths" -
3

Fitting Kit EN
K751W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4

Fitting Kit EN
K751W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Please check the front of this manual for
information relating specifically to your
vehicle.
5

Fitting Kit EN
K751W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
6

Fitting Kit EN
K751W
Fitment
●Open or remove fixed-point covers.
●Locate fixed clamping block A
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 095
B = 096
●Hook small claw into rear of the clamping
block
●Hook large claw into front of the clamping
block
7

Fitting Kit EN
K751W
●Refer to the underside of the pad for the
part number.
●Letters refer to the pad part numbers and
position.
●It is important to put the pads in the correct
position on the vehicle.
●Pad Part Number:
A = 233
B = 234
C = 267
D = 268
●Ensure internal clamp sits upright.
●Fit pad carefully over fixed point and clamp
screw.
8

Fitting Kit EN
K751W
●Mount crossbars over clamps.
●Repeat for all legs.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat for all four positions.
9

Fitting Kit EN
K751W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10