Whispbar K678W User manual

K678W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 2 x 1 x 1
x 1 x 1 x 1 x 1
x 4 x 2 x 1 x 1
Revision No: 4D 1

Fitting Kit K678W
MAX kgs (lbs)
W/P WHD
Toyota
Prius C, 5dr Hatch 12-15 NZ 40 kgs (88 lbs) 40 kgs (88 lbs)
Prius C, 5dr Hatch 12-15 AU 40 kgs (88 lbs) 40 kgs (88 lbs)
Prius C, 5dr Hatch 12-15 US 40 kgs (88 lbs) 40 kgs (88 lbs)
Prius C, 5dr Hatch 15-+ AU 40 kgs (88 lbs) 40 kgs (88 lbs)
Prius C, 5dr Hatch 15-+ NZ 40 kgs (88 lbs) 40 kgs (88 lbs)
Prius C, 5dr Hatch 15-+ US 40 kgs (88 lbs) 40 kgs (88 lbs)
2

Fitting Kit K678W
X
A B C 1 2 3
Prius C, 5dr Hatch 12-15 (NZ) -160mm 560mm - 705mm 680mm -
-6 -5/16ths" 22 1/16ths" - 27 3/4ths" 26 3/4ths" -
Prius C, 5dr Hatch 12-15 (AU) -160mm 560mm - 705mm 680mm -
-6 -5/16ths" 22 1/16ths" - 27 3/4ths" 26 3/4ths" -
Prius C, 5dr Hatch 12-15 (US) -160mm 560mm - 705mm 680mm -
-6 -5/16ths" 22 1/16ths" - 27 3/4ths" 26 3/4ths" -
Prius C, 5dr Hatch 15-+ (AU) -160mm 560mm - 705mm 680mm -
-6 -5/16ths" 22 1/16ths" - 27 3/4ths" 26 3/4ths" -
Prius C, 5dr Hatch 15-+ (NZ) -160mm 560mm - 705mm 680mm -
-6 -5/16ths" 22 1/16ths" - 27 3/4ths" 26 3/4ths" -
Prius C, 5dr Hatch 15-+ (US) -160mm 560mm - 705mm 680mm -
-6 -5/16ths" 22 1/16ths" - 27 3/4ths" 26 3/4ths" -
3

Fitting Kit EN
K678W
Attention:
●This vehicle is manufactured with an alloy
roof. Do not exceed the recommended
40kg maximum load limit on this vehicle.
●Please take care upon installing and
loading your roof racks.
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
4

Fitting Kit EN
K678W
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
5

Fitting Kit EN
K678W
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
6

Fitting Kit EN
K678W
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 970A
B = 971A
C = 974A
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
7

Fitting Kit EN
K678W
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
8

Fitting Kit EN
K678W
●Press adjusting screw to adjust the leg
positions on the crossbar.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
9

Fitting Kit EN
K678W
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
ATTENTION: This vehicle is manufactured with an
alloy roof. Do not exceed the recommended 40kg
maximum load limit on this vehicle.
Please take care upon installing and loading your
roof racks.
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10