Whispbar K918W User manual

K918W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 4
Revision No: 4D 1

Fitting Kit K918W
MAX kgs (lbs)
W/P WHD
Land Rover
Discovery Sport, 5dr SUV 14-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Discovery Sport, 5dr SUV 14-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Discovery Sport, 5dr SUV 14-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Discovery Sport, 5dr SUV 14-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Discovery Sport, 5dr SUV 14-+ CN 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K918W
X
A B C 1 2 3
Discovery Sport, 5dr SUV 14-+ (NZ) -195mm 555mm - 995mm 990mm -
-7 -11/16ths" 21 7/8ths" - 39 3/16ths" 39" -
Discovery Sport, 5dr SUV 14-+ (AU) -195mm 555mm - 995mm 990mm -
-7 -11/16ths" 21 7/8ths" - 39 3/16ths" 39" -
Discovery Sport, 5dr SUV 14-+ (EU) -195mm 555mm - 995mm 990mm -
-7 -11/16ths" 21 7/8ths" - 39 3/16ths" 39" -
Discovery Sport, 5dr SUV 14-+ (ZA) -195mm 555mm - 995mm 990mm -
-7 -11/16ths" 21 7/8ths" - 39 3/16ths" 39" -
Discovery Sport, 5dr SUV 14-+ (CN) -195mm 555mm - 995mm 990mm -
-7 -11/16ths" 21 7/8ths" - 39 3/16ths" 39" -
3

Fitting Kit EN
K918W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K918W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K918W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Grey
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
6

Fitting Kit EN
K918W
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A793
B = C646
7

Fitting Kit EN
K918W
●Attach clamp to each leg.
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8

Fitting Kit EN
K918W
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
●Check crossbar is securely attached to the
vehicle.
9

Fitting Kit EN
K918W
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10