Whittier Wood 1356AFGAC User manual

Production Code:
07/10
VN
P.O. Box 2827
Eugene, OR 97402 USA
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
Before you lmove this item, check to make
sure all screws and supports are tight.
.
Before you begin your project, completely read the
Assembly Instructions.
For normal household use only. Not recommended
for commercial use.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a
cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Designate the finish, provide the furniture model
number (upper portion of this page), the part letter,
production code, quantity needed, reason for replacement
and your full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m.
(Pacific Time). You may leave a message 24 hours
a day, seven days a week.
Model #
McKenzie Headboard
1356AFGAC; 1356AFCAF McKenzie Twin Headboard
1357AFGAC; 1357AFCAF McKenzie Full/Queen Headboard
1358AFGAC; 1358AFCAF McKenzie King/Cal-King Headboard
Assembly Instructions
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
1357AFGAC shown above.

1356AFGAC; 1356AFCAF McKenzie Twin Headboard
1357AFGAC; 1357AFCAF McKenzie Full/Queen Headboard
1358AFGAC; 1358AFCAF McKenzie King/Cal-King Headboard
— Parts List
A — Headboard Assembly — Qty.1
(for 1357AFGAC; 1357AFCAF
& 1358AFGAC; 1358AFCAF)
1357AFGAC shown above.
F — Headboard Assembly
— Qty.1
(for 1356AFGAC; 1356AFCAF)
B — Block 1
— Qty. 2 (attached)
G — Block 2
— Qty. 2 (attached)
C — #12 x 2-1/2" Pan Head
Screw — Qty. 8 (inserted)
Page 2 — 1356AFGAC_1356AFCAF_1357AFGAC_1357AFCAF_1358AFGAC_1358AFCAF — 07/10
(for 1356AFGAC; 1356AFCAF)
(for 1357AFGAC; 1357AFCAF
& 1358AFGAC; 1358AFCAF)
H — #8 x 1-5/8" Black Screw
— Qty. 4 (inserted)
I — #8 x 20mm Pan Head Screw
— Qty. 17 (inserted) (1356AFGAC; 1356AFCAF)
— Qty. 22 (inserted) (1357AFGAC; 1357AFCAF)
— Qty. 26 (inserted) (1358AFGAC; 1358AFCAF)
D — #12 x 1-1/4" Pan
Head Screw — Qty. 6
E — Washer
— Qty. 6
Assembly Instructions
Tools Required: Drill, 1/8" bit, Phillips screwdriver
1.
IF YOU ARE USING A HOLLYWOOD BED FRAME:
Adjust the Hollywood frame to fit your matress and box spring.
2. Place the Headboard (A) against the end brackets of the frame and mark the locations for
the screws. Drill pilot holes approximately 1-1/4" deep. (To make sure you don’t drill deeper,
measure 1-1/4" up from the end of the drill bit and wrap a piece of tape around the bit. Stop drilling
when the edge of the tape meets the wood.)
3. Position the Headboard (A) against the frame and attach using #12 x 1-1/4" Pan Head Screws (D)
and Washers (E).
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and model name.