Whittier Wood Stayton 3460AFCAF User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 04/13
Stayton Media
Tables
AFCAF = Caffè finish
Assembly Instructions
Model #
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for
commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelves.
Before you load or move this unit, tighten all screws and
supports.
Before you begin your project, completely read the
Assembly Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a cold
and possibly damp cement floor).
Periodically inspect your furniture for any loose glue
joints, screws or any other problem that might affect the
stability of your furniture. Tighten or repair as needed.
WARNING
Serious or fatal crushing injuries can occur from
furniture tip-over. To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors
or shelves.
Never open more than one drawer at a time.
Use of tip-over restraints may only reduce but not
eliminate the risk of tip-over.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
3462AFCAF
Stayton Media
Center
3460AFCAF
Stayton Media
Console

3460AFCAF Stayton Media Console;
3462AFCAF Stayton Media Center
Parts List
3460AFCAF_3462AFCAF —Page 2 —04/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
3460AFCAF
3462AFCAF
A
Top Assembly (attached)
1
1
B
Leg
4
4
C
Lower Shelf Assembly
1
1
D
Upper Shelf Assembly
1
1
E
Back Assembly
1
1
F
Drawer Box (inserted)
1
1
G
Drawer Face (installed)
1
1
H
Drawer Slides (pre-installed sets)
1
1
I
#6 x 3/4" Philtruss Screw (inserted)
4
6
J
#6 x 1/2" Philtruss Screw (inserted)
4
6
K
#6 x 5/8" Philtruss Screw
6
6
L
#8 x 1" Lo-Profile Screw (inserted)
6
6
M
#8 x 1-1/4" Pan Head Screw
42
(34 inserted)
45
(37 inserted)
N
#8 x 1-1/2" Machine Screw (installed)
4
4
O
#8 Washer (inserted)
18
21
P
5/16" Flat Washer
4
4
Q
3/8" x 1" Insert Nut (inserted)
4
4
R
3/8" x 2-1/2" Hex Bolt
4
4
S
1/4" x 20mm Insert Nut (inserted)
4
4
T
Pull (installed)
2
2
U
Wood Dowel (inserted)
8
8
V
Adjustable Glide (installed)
4
4
TR
Furniture Tipping Restraint
2 sets
2 sets
3462 shown in the illustrations.

3460AFCAF Stayton Media Console;
3462AFCAF Stayton Media Center
Assembly Instructions
3460AFCAF_3462AFCAF —Page 3 —04/13
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (F) from the Top Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a.
2. Turn the Top Assembly (A) upside-down on a clean, protected surface. Place two Legs (B) at
the back of the Top Assembly (A), making sure the drilled corners of the legs face toward the
Corner Blocks. Attach with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R). See Figures
2 and 2a.
Fig. 2
B
B
Fig. 2a
A
P
R
x 2
x 2
R
P
Fig. 1
Drawer Release Lever
Fig. 1a

3460AFCAF Stayton Media Console;
3462AFCAF Stayton Media Center
Assembly Instructions
3460AFCAF_3462AFCAF —Page 4 —04/13
3. Rotate the Top and Leg assembly so that is sets on the back legs. Turn the Lower Shelf
Assembly (C) and the Upper Shelf Assembly (D) bottom-side-down and place the dowels into
the dowel holes in the Legs. See Figure 3.
4. Using the dowels as guides, place the remaining Legs (B) in the remaining two corners making
sure the drilled corners of the Legs face toward the Corner Blocks. See Figures 4 and 4a.
Fig. 4
Fig. 4a
Fig. 3
C
D

3460AFCAF Stayton Media Console;
3462AFCAF Stayton Media Center
Assembly Instructions
3460AFCAF_3462AFCAF —Page 5 —04/13
5. Attach the legs to the Top Assembly with 5/16" Flat Washers (P) and 3/8" x 2-1/2" Hex Bolts (R)
See Figures 5 and 5a.
6. Turn the unit onto its top and using the pocket holes as guides, secure the Lower Shelf
Assembly (C) and the Upper Shelf Assembly (D) to the Legs (B) with eight #8 x 1-1/4" Pan Head
Screws (M). See Figures 6 and 6a.
Fig. 6
M
x 8
Fig. 6a
M
Fig. 5
Fig. 5a
P
R
x 2
x 2
P
R

3460AFCAF Stayton Media Console;
3462AFCAF Stayton Media Center
Assembly Instructions
3460AFCAF_3462AFCAF —Page 6 —04/13
7. Lay the unit with the drawer opening face down. The back apron of the Top Assembly has pre-
punched location holes. Place the Back Assembly (E) with the horizontal cleat of the top edge
against the back apron of the Top Assembly. Attach by inserting three #6 x 5/8” Philtruss
Screws (K) through the pre-punched location holes in the Back Apron. Insert three additional #6
x 5/8” Philtruss Screws through the holes in the bottom edge of the Back Assembly into the
Lower Shelf Assembly.
8. Turn the table upright and insert the Drawer. See Figure 8.
9. Place the unit at its final destination. To level the table, rotate the Adjustable Glides (V) found on
the bottoms of the legs. See Figure 8.
Fig. 8
V
V
Fig. 7
K
x 6
E
K
(Front View of
Back Assembly)
Fig. 7a
E
TOP

3460AFCAF Stayton Media Console;
3462AFCAF Stayton Media Center
Assembly Instructions
3460AFCAF_3462AFCAF —Page 7 —04/13
10. Tipping restraint: Locate two studs in the wall behind the unit. Attach a Clip (T1) to one wall
stud with two #8 x 2" Black Screws (T3). See Figure 10a. Attach a second clip to the unit with
two #6x5/8" Philtruss Screws (T5). See Figure 10b. Connect the two clips with the Nylon
Restraint Strap (T2). Pull the Nylon Restraint Strap (T2) tight so there is no slack. See Figures
10c and 10d. Repeat this procedure to attach the second tipping restraint. If you cannot locate
two studs, purchase the proper wall attachment hardware for your type of wall and secure the
unit.
Fig. 10a
T1
T3
Pull tight
Fig. 10d
T5
Fig. 10b
T1
B
T1
T2
T5
Fig. 10c
Pull the Nylon Restraint
Strap (T2) tight
so there is no slack.
T3