Wiedamark ColorBlock RGB LED Wall Washer 36 1W ETL... User manual

Wiedamark.com | 4016 Harry Hines Blvd, Dallas, Texas 75219 | 800.893.9787
ColorBlock RGB LED Wall Washer 36 1W, ETL Listed
is product is mainly used for decorating and highlighting in
building frame, garden, etc. It can work in independent mode
and DMX mode, which can generate various color changing
eects, such as ashing, fading, steady ,seven color jumping syn-
chronously etc. DMX256 class gray degree dimmer DMX pro-
grammable (thousands of eects available if many lights being
connected together);
A. Specication
Materials of Shell: Aluminum alloy
Rotary angle: 150°(Vertical)
Input Voltage: 120V/240V AC
Operating Voltage: 24V DC
Protecting Rating: IP65
Operating Temperature -20°C~40°Cv
1. Preprogrammed Operation. Select program, adjust color
and speed options using buttons and display located on end of
xture.
2. DMX Operation. Use buttons and display to assign DMX
address. Connect to DMX controller via the 3-pin IP68 threaded
connector.
3. Master/Slave Mode. Synchronize multiple units by intercon-
necting with IP68 threaded DMX cabling and assigning one unit
as “Master” and other units as “Slave” via the buttons and display
on the end of the xture.
FUNCTIONS SECTIONS INDEX:

Wiedamark.com | 4016 Harry Hines Blvd, Dallas, Texas 75219 | 800.893.9787
FUNCTION SELECTION:
1. Preprogrammed Operation
1. Press button “B” to enter the preprogrammed operation.
2. ree characters will appear on the display: e letter “P”
with 2 digits to the right of it.
3. e digit in the middle (X) can be selected by pressing the
“A” button and can be changed by pressing the “B” button.
4. e middle digit has a range of values that are: A, B, C, 1,
2, 3 , 4, 5, 6, 7, 8 and 9. e character selected for this middle
digit determines the program.
5. e last digit (Y) has a range of numeric values from 1 to 9.
e character selected for the last digit determines the speed
or rate for the program: 1 is slowest while 9 is the fastest.
6. About 10 seconds aer the last button is depressed, the
display will accept your change and store it in memory.
ColorBlock RGB LED Wall Washer 36 1W, ETL Listed
BA
YX
X Value Y Value
1- Static Red 1~9 Intensity
2- Static Green 1~9 Intensity
3- Static Yellow 1~9 Intensity
4- Static Blue 1~9 Intensity
5- Static Purple 1~9 Intensity
6- Static Cyan 1~9 Intensity
7- Static White 1~9 Intensity
8- Multicolor Changing 1~9 Speed
9- Single Fading 1~9 Speed
A- Multicolor Fading 1~9 Speed
B- Multicolor Flashing 1~9 Speed
C- Auto Run 1~9 Times Cycle

Wiedamark.com | 4016 Harry Hines Blvd, Dallas, Texas 75219 | 800.893.9787
3. Master/Slave Operation
1. is program will allow all lights that are inter-connected
with DMX cabling to operate in synchronized unison with the
unit assigned as the Master.
2. ere can only be one Master xture. To assign Master
status, follow the instructions for DMX Mode Operation and
assign the DMX address of 001. is will be the Master unit.
3. Assign any other DMX addresses, (with the exception
of 001) to the remaining lights that you want to operate as
Slaves.
4. Interconnect all lights with DMX cabling.
5. Now, whatever parameter you change on the Master unit
with the 001 address, will automatically be mirrored on the
remaining lights.
1. To control with DMX you must assign the light a numeric
3-digit address.
2. Press button “A” until three numeric characters appear on
the display.
3. Now, press the “B” button to increase the value of the
ashing character. Keep pressing “B” until you arrive at the
correct digit.
4. Press “A” to move number selection to the middle character.
Again, use “B” to select the correct digit for your DMX
address.
5. Repeat step 4 again to assign the rst digit of your DMX
address.
6. When done, simply wait for the display to stop ashing,
which will conrm it has accepted your DMX address
assignment.
7. Connect the DMX Out from your controller to the DMX In
cable which is located nearest the power cord.
ColorBlock RGB LED Wall Washer 36 1W, ETL Listed
2. DMX Mode Operation
BA
BA

Wiedamark.com | 4016 Harry Hines Blvd, Dallas, Texas 75219 | 800.893.9787
ColorBlock RGB LED Wall Washer 36 1W, ETL Listed
Technical Specications
Part Numbers
Part Number
Description
Unit
HWW-X036T-038070-H1
36LEDs, RGB, 120VAC, 15 degree, L333*W147*H210 mm
PCs
HWW-X036T-038070-H2
36LEDs, RGB, 240VAC, 15 degree, L333*W147*H210 mm
PCs
Technical Specifications
Physical Specifications
Chip Type Edison
Dimension L333*W147*H210 mm (L13.11*W5.79*8.27 inch)
Connectors XLR3
Material of Shell aluminum alloy
Weight 4.3 Kg±5%
Rotary Angle 180°
IP Rating IP65 (applicable for dry, wet, damp environment)
Electrical Specifications
Lighting Source 1W XPower LED
LED Quantity 36 LEDs
Operation Temperature -20 ℃~40 ℃(-4℉~104℉)
Input Voltage 100 VAC~256 VAC
Power Consumption 55 W (Max.)
Maximum Series-wound Length 100 meter (328 feet)
Control System DMX Control & Self-Control
Optical Specifications
Lumens (single LED) Red: 44 lm Green: 70 lm Blue: 15 lm
Beam Angle 15º
Lighting Distance 20 meter (65.6 feet)
Lumen Maintenance >85% @1000hrs
Wavelength Red: 620-625 Green: 520-525 Blue: 470-475
www.atgelectronics.com