wiking Miro 1 User manual
01.11.2020 / 53-0756
Installation- and User’s Manual
made by
EN
WIKING Miro 1
WIKING Miro 2
WIKING Miro 3
WIKING Miro 4
WIKING Miro 5
WIKING Miro 6
Contents
Drawings ............................................................................................................3-8
Installation ............................................................................................................. 9
Firing manual - wood........................................................................................... 14
Firing in general .................................................................................................. 17
Maintenance........................................................................................................ 18
Declaration of Performance ................................................................................ 20
Product informaiton EcoDesign .......................................................................... 21
Trouble Shooting ................................................................................................. 22
......................................................................................... 24
Page 3 of 24 pages
AB
CD
E
Page 4 of 24 pages
F
Page 5 of 24 pages
G1
Page 6 of 24 pages
G2
Page 7 of 24 pages
G3
Page 8 of 24 pages
H
2
1
Page 9 of 24 pages
In general
Congratulations on your new WIKING woodburning stove. We are pleased that you have cho-
optimum operation and safety, we recommend that the installation should be carried out by an
retailers, visit www.wiking.com under “Retailer locations”.
Safety
The installation of your WIKING woodburning stove must always comply with all European,
national and local building regulations. The installation must be carried out in accordance with
the instructions in the installation and user manuals and subsequently registered with the local
authorities. Upon installation, the chimney sweep must approve the installation before you can
start using the woodburning stove. All WIKING woodburning stove packaging material must be
handled in accordance with local waste management regulations.
Room requirements
Always ensure a supply of fresh combustion air to the room where the stove is to be installed.
The woodburning stove uses approx. 8-21 m3 of air per hour. A window that can be opened
valve/grate. In newly built/airtight dwellings, we recommend that a fresh air system should be
installed for the direct supply of external air to the combustion. This fresh-air system may be
bought separately.
withstand the weight of the stove and the chimney. The weight of the chimney should be cal-
culated according to its dimensions and height.
Technical measures and data
Test results from nominal test EN 13240
4.9 kW
Flue gas temperature EN 13240 measurement point 295ºC
Flue gas temperature measured in the outlet socket 326ºC
5.2 g/s
78 %
68 %
PM 18.2 mg/m3
OGC 66 mg/m3
NO2114 mg/m3
CO at 13% O21125 mg/m3
CO at 13% O20.09 %
103
A
Test result based on NS 3058
Particle emissions 3.05 g/kg
Page 10 of 24 pages
Norsk
Model Weight Height Width Dept
Miro 1 79 kg 71.2 cm 46.8 cm 35.5 cm
Miro 1 on pedestal 90 kg 110.8 cm 46.8 cm 35.6 cm
Miro 2 82 kg 71.2 cm 46.8 cm 35.5 cm
Miro 2 on pedestall 93 kg 110.8 cm 46.8 cm 35.6 cm
Miro 3 93 kg 101.2 cm 46.8 cm 35.6 cm
Miro 4 93 kg 101.2 cm 46.8 cm 35.6 cm
Miro 4 with natural stone cladding 217 kg 104.4 cm 54.5 cm 35.6 cm
Miro 4 with tile cladding 130 kg 104.4 cm 54.5 cm 35.6 cm
Miro 5 94 kg 131.4 cm 46.8 cm 35.6 cm
Miro 6 97kg 131.4 cm 46.8 cm 35.6 cm
Miro 6 with natural stone cladding 252 kg 135.1 cm 54.5 cm 35.6 cm
Miro 6 with tile cladding 143 kg 135.1 cm 54.5 cm 35.6 cm
Heat storage stones, Miro 5+6 34 kg
Floor plate
European, national and local regulations must be observed in terms of the size and thickness
your WIKING retailer for assistance. The combustion chamber opening is 35,2 cm wide.
Distance to combustible materials
Min. distances
- uninsulated ue gas pipe:
Miro 1
Miro 3
Miro 5
Miro 2
Miro 4
Miro 6
Miro 4 med
stone-/ tile cladding
Miro 6 med
stone-/ tile cladding
Recommended for brick wall, back 10 cm 10 cm 10 cm
Recommended for brick wall, side 15 cm 10 cm 10 cm
For combustible wall, back 10 cm 10 cm 10 cm
For combustible wall, side 52 cm 31 cm 31 cm
To combustible wall,
corner installation, 45º
38 cm 10 cm 10 cm
7* cm 7* cm
Distance to furnishings in front 90 cm 90 cm 90 cm
* Applies only to WIKING Miro 1 and WIKING Miro 2. This distance requirement is observed when the wood-burning stove is mounted on a
pedestal or a wall with the required distance below the wood-burning stove.
Remember to pay attention to the applicable regulations concerning the required distance
between the wall and smoke pipe.
Please be aware that not all glass parts are heat-resistant. For this reason, a glass wall should
sometimes be treated as a combustible wall, in which case we ask you to contact your local
chimney sweep or glass producer to hear at what distance the stove should be kept from glass.
Requirements for chimney and smoke pipe
As a general rule, satisfactory draught conditions are achieved if the chimney is 4 m above
Page 11 of 24 pages
the stove and at least 80 cm above the ridge. If the chimney is placed at side walls, the top of
the chimney should always be higher than the ridge or the tallest point of the roof. Always be
aware of any national and/or local regulations applying to thatched roofs and the location of
the chimneys.r.
-
18-20 Pa.
The chimney must have a minimum clearing of Ø 150 mm. The chimney must be provided with
The required distance to combustible material must be complied with in accordance with the
brand label. Ask your WIKING retailer for further information.
Changing the Smoke Outlet from Top Outlet to Back Outlet (WIKING Miro 1 - Miro 4)
Proceed as follows to change the smoke outlet from top outlet to rear outlet:
5. Install the cover plate on top of the stove with the three screws.
6. Place the smoke ring in the smoke outlet hole in the back of the stove and secure it with the
three screws.
7. Replace the top plate on the stove.
A top cover can be bought as an accessory to cover the hole in the top plate of the stove if the
stove is connected to a rear smoke outlet.
Changing the Smoke Outlet from Top Outlet to Rear Outlet (WIKING Miro 5 - Miro 6)
(drawing F)
Proceed as follows to change the smoke outlet from top outlet to rear outlet:
and forward.
compartment. Remove the smoke ring.
-
the three screws.
Page 12 of 24 pages
A top cover can be bought as an accessory to cover the hole in the top plate of the stove if the
stove is connected to a rear smoke outlet.
Connection to chimney
All the stoves have both back and top smoke outlet that can be connected to an approved steel
chimney on top or directly out at the rear to a chimney.
Make sure that the chimney is tight and that no false draft is caused around neither the cover
plate, in connection with a covered smoke outlet, nor the cleanout door and pipe connections.
3. Vermiculite rear plate.
4. Vermiculite corner plate.
5. Vermiculite side plate.
6. Bottom plate
7. Protection during transportation
8. Fittings
Please note: The combustion chamber is covered with plates made of vermiculite, which is a
heat-insulating material. These plates ensure that the optimal combustion temperature is quickly
reached, and they must therefore remain inside in the wood-burning stove.
their warmth within the stove and the surrounding area. In this way you get more warmth from
the wood you add to the stove, as the warm smoke is not simply sent out through the chimney.
Fitting the loose parts
that all insulation plates of the combustion chamber have been properly placed, i.e. that the
bottom plate is horizontal and that the side plates are vertical and reach all the way up to the
steel sides of the combustion chamber and down to the bottom plate.
1.
as protection during transportation. Remember to remove the two pins before you start
using the stove.
2.
of the combustion chamber and must be pushed as far back as possible into the combu-
stion chamber.
3.
4.
Page 13 of 24 pages
Chimney
The chimney is the “engine” of the stove and it is crucial for the functioning of the woodburning
stove. The chimney draft provides a partial vacuum in the stove. This vacuum removes the
smoke from the stove, sucks air through the dampers for the so-called glass pane rinse which
keeps the glass free of soot, and sucks in air through both primary and secondary dampers
for the combustion.
The higher the temperature within the chimney, the greater the draft. It is crucial, therefore, that
the chimney is warmed up properly before closing the damper and limiting the combustion in the
On days where the wea-
If the stove has not been used for a longer period, it is important to check that the chimney pipe
is not blocked.
check the applicable rules.
Chimney sweeping
the chimney is too tall to be cleaned from above, it must be equipped with a soot door.
have the chimney checked by the chimney sweeper.
The type badge and the serial number (Drawing C)
On WIKING Miro 1/Miro 2 the type badge and serial number are glued onto an extension plate
located in the left side next to the locking hook.
On WIKING Miro 3/Miro 4/Miro 5/Miro 6 the type badge and the serial number are placed on
the inside of the door below the combustion chamber.
Page 14 of 24 pages
Your first heating session
The lacquer will be fully hardened after the stove has been used, and the door and the ashpan
should be opened very carefully as there will otherwise be a risk that the gaskets will stick to
that the room is well ventilated.
Warning:
Tips about fuel
Approved fuel types
The wood burning stove is EN approved for combustion of wood only. It is recommended to
Recommended wood types
All types of wood, for instance birch, beech, oak, elm, ash, conifers, and fruit trees can be used
types per cubic metre. Beech weighs more per m3of wood than common spruce, for instance.
This is why more common spruce is required, in terms of volume, to obtain an amount of heat
similar to that of beech. Heavy types of wood such as ash, beech, oak and elm are generally not
wood such as birch, maple, spruce and pine are more easy to light up. They burn faster and give
the heavier types of wood to ensure a longer burning time..
Banned fuel types
fuels, and rubbish such as milk cartons, lacquered wood or impregnated wood and fossil fuels.
The reason that you should not apply any of the above is that during combustion they develop
substances that are health hazardous and harmful to the environment. These substances
could also damage your wood burning stove and chimney, rendering the product warranty
void.
Storage of wood
A moisture content of 12-18% is achieved by storing recently felled wood outdoors under a
lean-to for at least one year, preferably 2 years. Wood stored indoors has a tendency to be-
come too dry and combust too quickly. However, it might be advantageous to store fuel for
Split the wood and measure the mois-
ture content of the split surfaces.
Recommended dimensions
The dimensions of the fuel are important to good combustion. The dimensions should be as
Page 15 of 24 pages
Norsk
follows:
Fuel type Length in cm Diameter in cm
20-30 2-5
Chopped wood 20-30 7-10
Using the Air Damper
located under the stove door; see drawing D.
When lighting a cold stove and when fuellingwith new wood, the regulating lever must be pu-
air supply can be gradually reduced by moving the regulating lever to the right.
stove has been allowed to go out completely in connection with cleaning, for instance.
Special re lighting guide for stoves with stone and tile cladding
Stone are natural products which need to adjust to temperature changes. We recommend
following the procedure below:
1. First stoking
Move the air control lever to the extreme left to fully open the air supply to
-
close the stove door. If condensation forms on the glass, keep the door
ajar for a little while and close again.
temperature.
2. Second stoking
Move the air control lever to the extreme left to fully open the air supply to the combustion
-
stove door. If condensation forms on the glass, keep the door ajar for a little while and close
again. The layer of embers is suitable when the pieces of wood begin to disintegrate and the
air supply can be gradually reduced by moving the air control lever to the right until uniform,
before stoking again.
3. Third stoking
Restoking
Follow the general instructions, see the sections “Lighting the stove” and “Stoking”.
Page 16 of 24 pages
Lighting the stove
A successful combustion process requires that the wood is lit in the right way. A cold stove
and a cold chimney challenge the combustion process. Be careful to make a good lighting with
Move the air control lever to the extreme left to fully open the air supply to
-
close the stove door. If condensation forms on the glass, keep the door
the air supply can be gradually reduced by moving the air control lever to the right until uniform,
steady combustion is achieved.
Important! The ash pan must not be opened during the lighting stage and must always be
kept closed when the stove is lit or the WIKING®Automatic™ might be damaged. Only open
the door when lighting the stove, refuelling it and cleaning it. Never leave a stove before there
Stoking
The layer of embers is suitable when the pieces of wood begin to disintegrate and the bottom
of the stove is covered by embers. Carefully open the door to prevent smoke and embers from
Close the door again and fully open the air supply by moving the regulating lever to the ex-
by moving the air control lever to the right until uniform, steady combustion is achieved. The
steady combustion.
During combustion, the outer surfaces of the stove will become hot, and due care must
therefore be shown.
When burning is complete
When the stove is not in use, turn the air control lever all the way to the right.
Cleaning the glass
Fuelling with coal or pet coke
The stove is not approved to use coal or pet coke as a fuel.
Page 17 of 24 pages
Rapid or erce heat
Maximum amounts of fuel:
The maximum allowed amount of fuel per hour is:
Wood: 2.5 kg
If these limits are exceeded, the stove will no longer be covered by the factory guarantee, and
it may also become damaged due to excessive heat, the glass may turn white, for example..
The stove has been approved for intermittent use.
Typical re-ring interval
Prolonged burning time
How to achieve the best combustion
• Use clean and dry wood
heat will dry the wood, not heat up the room.
• The re should only be stoked with a little wood at a time
you achieve a good combustion.
• Make sure there is the right amount of air
temperature in the wood burning stove climbs quickly. In this way the gasses and particles
• Don’t savour the re during night time
an attempt to still have some embers left in the morning. If you do so, large amounts of
hazardous smoke will be emitted, and your chimney will be exposed to unnecessarily large
Page 18 of 24 pages
Cleaning
Any maintenance of the stove should only be carried out when it is cold. Daily maintenance is
dust the stove using a dry, soft cloth or brush. But remember, only when the stove is cold. Do
not use water, spirit or any other kind of cleaner, as this will damage the lacquer.
Once a year, the stove should be thoroughly serviced. The combustion chamber should be
cleared of ashes and soot. The hinges and the closing hook must be greased with liquid cop-
onto the hinge leaf.
Service inspection
• Thorough cleaning of the stove.
• Checking the spring in the WIKING®Automatic™. Replace if necessary.
• Checking gaskets. Replace gaskets if they are not intact or are no longer soft.
• Checking and/or replacing insulation material.
• Checking the combustion chamber base.
• Use copper grease for hinges and locking hooks
Inside cleaning
Before chimney sweeping can be performed, the air control lever must be set to its minimum
position to prevent soot and ash from entering the WIKING®Automatic™. Unless the safety
First remove ash and soot from the combustion chamber. In drawing
E you can see which plates are found inside the combustion chamber. Carefully remove the
vermiculite plates, one after the other, in the following sequence:
2. Rear plate
3. Left corner plate
4. Right corner plate
5. Left side plate
6. Right side plate
After cleaning, carefully put the vermiculite plates back in place in the reverse order starting
with the rear plate.
Ashes
It is easiest to empty the ash pan by pulling a plastic bag over it, turning it upside down and
then carefully removing it from the bag. Ashes are disposed of via the domestic waste col-
lection.
Please note that there may be embers in the ashes for up to 24 hours after the re has
gone out!
Page 19 of 24 pages
Insulation
-
plate can cause secondary air to become incorrectly distributed in the combustion chamber,
and it should therefore be replaced. However, it should be replaced, if there are actual holes
than half its original thickness.
WIKING®Automatic™
The spring in the automatism should be controlled at least once every second year.
WIKING Miro 1-4 (Drawing G1):
plate of the stove. On a cold stove, the starting point of the feeler is controlled. The starting
point on a cold stove is about 100 above horizontal. It should feel easy going and bouncy when
you push it, no matter if the stove is cold or hot. Mount the rear plate, the side plates and the
top plate again.
WIKING Miro 5-6 (Drawing G2):
both sides of the heat storage compartment. Open the door to the wood section and remove
On a cold stove, the starting point of the feeler is controlled. The starting point on a cold stove
is about 100 above horizontal. It should feel easy going and bouncy when you push it, no matter
if the stove is cold or hot. Re-mount the rear plate, the side plates, the bottom plate in the heat
storage compartment, the front of the heat storage compartment and the top plate.
WIKING Miro 4/WIKING Miro 6 with soapstone cover (Drawing G3): Remove the rear plate
of the stove. On a cold stove, the starting point of the feeler is controlled. The starting point on
a cold stove is about 100 above horizontal. It should feel easy going and bouncy when you push
it, no matter if the stove is cold or hot. Remount the rear plate.
Door/glass
A sooty glass door can easily be cleaned with a piece of moist kitchen roll dipped in ash. Go
should also ensure that air gaps in the door frame are free of ash and soot particles.
Seals
Check frequently to ensure that seals in the door and ash pan are intact and not brittle. Failing
this, they should be replaced. Use original seals only.
Surface
Usually, it is not necessary to any treatment to the painted surfaces of the wood-burning stove.
Any damage to the paint may, however, be remedied with spray paint, which can be bought
from your stove retailer.
Guarantee
Page 20 of 24 pages
The DoP can be downloaded from our website via the following links:
www.wiking.com/dop/Miro
Other manuals for Miro 1
5
This manual suits for next models
5
Table of contents
Other wiking Wood Stove manuals
Popular Wood Stove manuals by other brands
Vermont Castings
Vermont Castings Defiant 1975 Installation and operating manual
Lexington Forge
Lexington Forge SAVANNAHSSW40 owner's manual
RIKA
RIKA ALPHA II manual
Palazzetti
Palazzetti Ecomonoblocco 45 Series Instructions for use and maintenance
Century
Century CB00004 Installation and operation manual
True North
True North TN19 Installation and operating instructions
Ravelli
Ravelli APOLLO Installation, operation and maintenance manual
Drolet
Drolet Savannah DB03025 Installation and operation manual
ADURO
ADURO 14 user manual
Nibe
Nibe Contura C510 manual
Vermont Castings
Vermont Castings The Intrepid II 1990CE Homeowner's installation and operating manual
Englander
Englander 15-W06 Installation & operation manual