Quadra-Fire XPLRMED-PBK User manual

1 7061-197H November 10, 2015
Explorer II Medium Wood Stove
Model(s):
EXPLRMED-PBK
EXPLRMED-PDB
EXPLRMED-PFT
EXPLRMED-PMH
EXPLRMED-MBK
FRONT PAGE
WARNING
If the information in these instruc-
tions is not followed exactly, a


• Do not store or use gasoline or other  am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• Do not over re - If heater or chimney con-
nector glows, you are over ring. Over ring
will void your warranty.
• Comply with all minimum clearances to
combustibles as speci ed. Failure to
comply may cause house  re.
WARNING

For use with solid wood fuel only.
Other fuels may over re and generate
poisonous gases (i.e. carbon monoxide).
Installation and service of this appliance should
be performed by quali ed personnel. Hearth &
Home Technologies recommends NFI certi ed
professionals, or technicians supervised by an
NFI certi ed professional.
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.

• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
 replace.
• Alert children and adults to hazards of high temperatures
•       

• Keep clothing, furniture, draperies and other  ammable
materials away.
WARNING
Installation Manual
Installation & Appliance Set-Up


NOTICE: DO NOT DISCARD THIS MANUAL
NOTE
To obtain a French translation of this manual, please contact
your dealer or visit www.quadra re.com
Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadra re.com

2 7061-197H November 10, 2015
Explorer II Medium Wood Stove
TABLE OF CONTENTS
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
Quadra-Fire is a registered trademark of Hearth & Home Technologies.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the UL1482-07, (UM)
84-HUD and NPFA211 in the U.S.A. and the ULC S627-00 and
CAN/CSA-B365 Installation Codes in Canada. NOT APPROVED
FOR MOBILE HOME INSTALLATIONS IN CANADA!
1 Important Safety Information3
A. Appliance Certication ......................................................3
B. BTU & Efciency Specications........................................3
C. Mobile Home Approved (USA ONLY) ............................... 3
D. Glass Specications .........................................................3
E. Non-Combustible Materials ...............................................3
F. Combustible Materials........................................................3
2 4
A. Design and Installation Considerations .............................4
B. Fire Safety .........................................................................4
C. Negative Pressure............................................................5
D. Tools And Supplies Needed..............................................5
E. Inspect Appliance and Components .................................5
F. Install Checklist ..................................................................6
3 Dimensions and Clearances7
A. Appliance Dimensions ......................................................7
B. Clearances to Combustibles..............................................8
C. Locating Your Stove & Chimney .......................................9
D. Chimney Termination Requirements ................................9
E. 2-10-3 Rule ......................................................................10
4 Chimney Systems11
A. Venting Components .......................................................11
B. Chimney Systems.............................................................11
C. Installing Chimney Components........................................13
5 Appliance Set-Up14
A. Hearth Protection Requirements ......................................14
B. Outside Air Kit Installation .................................................15
C. Blower (Optional)..............................................................16
D. Reversible Flue Collar and Horizontal Flue Heat Shield ..17
6 18
7 Accessory List19

November 10, 2015 7061-197H 3
Explorer II Medium Wood Stove
Model: Explorer II Medium Wood Stove
 Intertek
Report No: 10126132PRT
Type: Safety
Standard: UL 1482-07; ULC S627-00
EPA Certication #: 925
EPA Certied Emissions: 2.2 grams per hour
*LHV Tested Efciency: 78.3 %
**HHV Tested Efciency: 72.4 %
***EPA BTU Output: 11,200 to 35,900 / hr.
****Peak BTU/Hour Output: 61,000
Vent Size: 6 inches
Firebox Size: 2.42 cubic feet
Recommended Wood Length: 20 inches
Fuel Orientation: Side-to-Side
Fuel Seasoned Cord Wood
* Weighted average LHV efciency using Douglas Fir dimension-
al lumber and data collected during EPA emissions test.
**Weighted average HHV efciency using Douglas Fir dimen-
sional lumber and data collected during EPA emissions test.
***A range of BTU outputs based on EPA Default Efciency and
the burn rates from the low and high EPA tests, using Douglas
Fir dimensional lumber.
****A peak BTU out of the unit calculated using the maximum rst
hour burn rate from the High EPA Test and the BTU content of
cordwood (8600) times the efciency.
The Quadra-Fire Explorer Series Wood Stove (ACC) meets
the U.S. Environmental Protection Agency’s crib wood emis-
sion limits for wood heaters sold after May 15, 2015.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.
1 Important Safety Information

NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specications and/or price without notice.

• This appliance is approved for mobile home installa-
tions in the USA when not installed in a sleeping room
and when an outside combustion air inlet is provided.
• The structural integrity of the mobile home oor, ceil-
ing, and walls must be maintained.
• The appliance must be properly grounded to the frame
of the mobile home with #8 copper ground wire, and
chimney must be listed to UL103 HT or a listed UL-
1777 full length six inch (152mm) diameter liner must
be used.
• Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualied
installer, service agency or your dealer.
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Operating appliance without legs attached (if supplied with
it).
• Do NOT Overre - If appliance or chimney connector glows,
you are overring.
Any such action that may cause a re hazard.
WARNING

Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:

Hearth & Home Technologies WILL NOT warranty stoves
that exhibit evidence of over-ring. Evidence of over-ring
includes, but is not limited to:
• Warped air tube
• Deteriorated refractory brick retainers
• Deteriorated bafe and other interior components

Material which will not ignite and burn, composed of any
combination of the following:
- Steel - Plaster
- Brick - Iron
- Concrete - Tile
- Glass - Slate
Materials reported as passing ASTM E 136, Standard



Material made of/or surfaced with any of the following ma-
terials:
- Wood - Compressed Paper
- Plant Fibers - Plastic
- Plywood/OSB - Sheet Rock (drywall)
Any material that can ignite and burn: ame proofed or not,
plastered or un-plastered.

This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.

4 7061-197H November 10, 2015
Explorer II Medium Wood Stove
Install Guide
2 

Consideration must be given to:
• Safety
• Convenience
• Trafc ow
• Chimney and chimney connector required
It is a good idea to plan your installation on paper, using exact
measurements for clearances and oor protection, before
actually beginning the installation. If you are not using an
existing chimney, place the appliance where there will be a
clear passage for a factory-built listed chimney through the
ceiling and roof.
We recommend that a qualied building inspector and your
insurance company representative review your plans before
and after installation.
If this appliance is in an area where children may be near it is
recommended that you purchase a decorative barrier to go
in front of the appliance. Remember to always keep children
away while it is operating and do not let anyone operate
this appliance unless they are familiar with these operating
instructions.
WARNING
• DO NOT CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION
DUCT OR SYSTEM.
May allow ue gases to enter the house.

• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with
unit).
• Do NOT Overre - If appliance or chimney connector glows,
you are overring.

WARNING

Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult insurance carrier, local building, fire officials or
authorities having jurisdiction about restrictions, installation
inspection, and permits.
CAUTION
NOTICE: HEARTH & HOME TECHNOLOGIES ASSUMES NO
RESPONSIBILITY FOR THE IMPROPER PERFORMANCE
OF THE APPLIANCE SYSTEM CAUSED BY:
• Inadequate draft due to environmental conditions
• Downdrafts
• Tight sealing construction of the structure
• Mechanical exhausting devices
• Overdrafting caused by excessive chimney heights
• Ideal performance is with height of chimney between 14-16 feet
(4.26-4.88m) measured from the base of the appliance.

To provide reasonable re safety, the following should be
given serious consideration:
1. Install at least one smoke detector on each oor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
2. A conveniently located Class A fire extinguisher to
contend with small res resulting from burning embers.
3. A CO detector should be installed in the room with the
appliance.
4. A practiced evacuation plan, consisting of at least two
escape routes.
5. A plan to deal with a chimney re as follows:
In the event of a chimney re:
a Evacuate the house immediately
b. Notify re department.

November 10, 2015 7061-197H 5
Explorer II Medium Wood Stove

Negative pressure results from the imbalance of air avail-
able for the appliance to operate properly. It can be stron-
gest in lower levels of the house.
Causes include:
• Exhaust fans (kitchen, bath, etc.)
• Range hoods
• Combustion air requirements for furnaces, water heaters
and other combustion appliances
• Clothes dryers
• Location of return-air vents to furnace or air conditioning
• Imbalances of the HVAC air handling system
• Upper level air leaks such as:
- Recessed lighting
- Attic hatch
- Duct leaks
To minimize the effects of negative air pressure:
• Install the outside air kit with the intake facing prevailing
winds during the heating season
• Ensure adequate outdoor air for all combustion appliances
and exhaust equipment
• Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the appliance
• Avoid installing the appliance near doors, walkways or
small isolated spaces
• Recessed lighting should be a “sealed can” design
• Attic hatches weather stripped or sealed
• Attic mounted duct work and air handler joints and seams
taped or sealed
• Basement installations should be avoided
WARNING
• Negative pressure can cause spillage of com-
bustion fumes, soot and carbon monoxide.
• Appliance needs to draft properly for safety.


Before beginning the installation be sure the following tools
and building supplies are available:
Reciprocating saw Framing material
Pliers High temp caulking material
Hammer Gloves
Phillips screwdriver Framing square
Flat blade screwdriver Electric drill and bits
Plumb line Safety glasses
Level Tape measure
Misc. screws and nails
1/2-3/4 in. length, #6 or #8 self-drilling screws
• Remove appliance and components from packaging and
inspect for damage.
• Report to your dealer any parts damaged in shipment.
 
     


Inspect appliance and components for damage.
Damaged parts may impair safe operation.
WARNING
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.


6 7061-197H November 10, 2015
Explorer II Medium Wood Stove
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.
Customer:
Date Installed:
Lot/Address:
Location of Fireplace:
Installer:


Model (circle one): EXPLRMED-PBK EXPLRMED-PDB EXPLRMED-PFT EXPLRMED-PMH EXPLRMED-MBK
WARNING! Risk of Fire or Explosion! Failure to install replace according to these instructions can lead to a re or explosion.
Appliance Install
Veried clearances to combustibles. (Pg. 8)
Hearth extension size/height decided. (Pg. 14)
Outside air kit installed. (Pg. 15)
Floor protection requirements have been met.
If appliance is connected to a masonry chimney, it should be cleaned and
inspected by a professional. If installed to a factory built metal chimney, the
chimney must be installed according to the manufacturer’s instructions and
clearances.
Chimney
Chimney conguration complies with diagrams.
Chimney installed, locked and secured in place with proper clearance.
Chimney meets recommended height requirements (14-16 feet).
Roof ashing installed and sealed.
Terminations installed and sealed.
Clearances
Combustible materials not installed in non-combustible areas.
Veried all clearances meet installation manual requirements.
Mantels and wall projections comply with installation manual requirements.
Protective hearth strips and hearth extension installed per manual requirements.
Appliance Setup
All packaging and protective materials removed.
Firebrick, bafe and ceramic blanket installed correctly.
All labels have been removed from the door.
All packaging materials are removed from inside/under the replace.
Manual bag and all of its contents are removed from inside/under the replace
and given to the party responsible for use and operation.

• Photographing the installation and copying this checklist for your le.
• That this checklist remain visible at all times on the replace until the installation is complete.
Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:
Comments communicated to party responsible by on
(Builder/Gen. Contractor) (Installer) (Date)
Part # 4017-254 • Rev B • 01/29/13
 
Install Checklist

November 10, 2015 7061-197H 7
Explorer II Medium Wood Stove
14-7/8
28-15/16
19-1/2
26-3/4


12-1/4
20-1/16
7-15/16
27
28-15/16

29
3
25-7/8
22-3/16

3 Dimensions and Clearances
 NOTE: Flue Collar size is 6 inch (152mm) diameter (ID)

8 7061-197H November 10, 2015
Explorer II Medium Wood Stove

BACKWALL / SIDEWALL
A B C
D
F
CORNER INSTALLATION
E
C
ALCOVE TOP VIEW
GA
ALCOVE SIDE VIEW



• Comply with all minimum clearances to
combustibles as specied.
• Failure to comply may cause house re.
WARNING
A B C D
INSTALLATION: FULL VERTICAL OR ALCOVE
SINGLE WALL PIPE
DOUBLE WALL PIPE
Explorer II 9-3/8 (238) 5-3/8 (137) 20-1/4 (514) 6-1/2 (165) 4-1/2 (114) 14-3/4 (375) 55 (1397)
Explorer II 10-1/2 (267) 6-1/2 (165) 20-1/4 (514) 6-1/2 (165) 7 (178) 17-1/4 (438) 55 (1397)
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS in inches & (Millimeters)
NOTE: A, C, and F Dimensions are to the center of the ue collar
For alcove only: Six inch diameter listed Double wall air insulated connector pipe with UL103 HT
listed factory built Class A chimney or masonry chimney. Maximum depth of Alcove shall be no
more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of unit and
the referenced clearances. Canada must comply with CAN/ULC-S269 M87 for the 650° factory
built chimney
E F G
* FOLLOW PIPE MANUFACTURES CLEARANCES AS REQUIRED
G
STOVE TO CEILING
CLEARANCE
*
12
(305)
20.25
(514)
50
(1270)
MANTEL
12” MAX
HORIZONTAL THROUGH WALL
TOP AND SIDE VIEW

November 10, 2015 7061-197H 9
Explorer II Medium Wood Stove
Recommended
Location
Marginal
Location
Location
Not
Recommended
Recommended
Location
Location NOT
Recommended
Multi-level Roofs
Windward
Leeward
Outside Air Kit Termination Cap


Follow manufacturer’s instructions for clearance, securing
ashing and terminating the chimney. 
•Must have an approved and Listed cap
•Must not be located where it will become plugged by
snow or other material
• Must terminate at least 3 feet (91cm) above the roof
and at least 2 feet (61cm) above any portion of the
roof within 10 feet (305cm).
• Must be located away from trees or other structures

Location of the appliance and chimney will affect perfor-
mance. As shown in  the chimney should:
• Install through the warm space enclosed by the build-
ing envelope. This helps to produce more draft, espe-
cially during lighting and die down of the re.
• Penetrate the highest part of the roof. This minimizes
the affects of wind turbulence and down drafts.
• Consider the appliance location in order to avoid oor
and ceiling attic joists and rafters.
• Locate termination cap away from trees, adjacent
structures, uneven roof lines and other obstructions.
Your local dealer is the expert in your geographic area and
can usually make suggestions or discover solutions that will
easily correct your ue problem.
NOTICE:
• Chimney performance may vary.
• Trees, buildings, roof lines and wind conditions affect
performance.
• Chimney height may need adjustment if smoking or
overdraft occurs.
NOTICE: Locating the appliance in a basement or in a
location of considerable air movement can cause intermittent
smoke spillage from appliance. Do not locate appliance near
• Frequently open doors
• Central heat outlets or returns

10 7061-197H November 10, 2015
Explorer II Medium Wood Stove
3 ft. (91cm)
Minimum
Less than 10 ft. (305cm)
2 ft. (61cm) 3 ft. (91cm)
Minimum
10 ft. (305cm) To Nearest Roofline
2 ft. (61cm)
Pitched Roof


10 ft. (305cm) or more
3 ft. (91cm) Minimum
Less than 10 ft. (305cm)
2 ft. (61cm) Minimum
3 ft. (91cm) Minimum
Wall or Parapet
Flat Roof


This appliance is made with a 6 inch (152mm) diameter chimney connector as the ue collar on the unit.
• Changing the diameter of the chimney can affect draft and cause poor performance.
• It is not recommended to use offsets and elbows at altitudes above 4000 feet above sea level and or when there
are other factors that affect ue draft.

November 10, 2015 7061-197H 11
Explorer II Medium Wood Stove
4 Chimney Systems
NOTE: In Canada when using a factory-built chimney it must
be safety listed, Type UL103 HT (2100
o
F) CLASS “A” or
conforming to CAN/ULC-S629M, STANDARD FOR 650oC

Floor
Protector
Chimney
Connector
Insulated "T "
Flashing
Listed Termination Cap
Trim Collar on
Inside Wall Listed Chimney
Storm Collar
Wall Support
Roof Brace (if required)
Thimble
Floor
Protector
Chimney
Connector
Ceiling Support
Listed Chimney
Listed Termination Cap
Storm Collar
Flashing
 

Chimney Connector:
It is also known as ue pipe or stove pipe. The chimney
connector joins the stove to the chimney. It must be a 6 inch
(152mm) minimum diameter 24 gauge mild steel black or 26
gauge blued steel, or an approved air-insulated double wall
venting pipe.
:
A manufactured or site-constructed device installed in
combustible walls through which the chimney connector
passes to the chimney. It is intended to keep the walls
from igniting. Site constructed thimbles must meet NFPA
211 Standards. Prefabricated must be suitable for use with
selected chimney and meet UL103 Type HT Standards. Follow
instructions provided by the manufacturer for manufactured
thimbles for masonry chimney and prefabricated chimneys.
Chimney:
The chimney can be new or existing, masonry or prefabricated
and must meet the following minimum requirements specied
in Section 5B.


• Must be minimum 6 inch (152mm) diameter (ID) high
temperature chimney listed to UL 103 HT (2100oF) or
ULC S629M.
• Must use components required by the manufacturer
for installation.
• Must maintain clearances required by the manufacturer
for installation.
• Refer to manufacturers instructions for installation.

12 7061-197H November 10, 2015
Explorer II Medium Wood Stove

Site constructed for masonry chimney installation:
Components
• A minimum length of 12 inches [305mm] (longer for
thicker walls) of solid insulated factory-built chimney
length constructed to UL 103 Type HT 6 inch (152mm)
inside diameter. Chimney needs to extend a minimum
of 2 inches (51mm) from the interior wall and a minimum
of 1 inch (25mm) from the exterior wall.
• Wall spacer, trim collar and wall band to t solid pack
chimney selected.
• Minimum 8 inch (203mm) diameter clay liner section (if
not already present in chimney) and refractory mortar.
• When jurisdiction requires install approved chimney
liner in masonry chimney.
Air Clearances
• Masonry chimney clearance must meet NFPA 211 mini-
mum requirement of 2 inches (51mm) to sheet metal sup-
ports and combustibles.
• Minimum of 1 inch (25mm) clearance around the chim-
ney connector.
• Top of wall opening is a minimum of 13-1/2 inches
(343mm) from ceiling or 4-1/2 inches (114mm) below
minimum clearance specied by chimney connector
manufacturer. NFPA 211 minimum vertical clearance of
18 inches (457mm) from chimney connector and ceiling
or minimum recommended by chimney connector manu-
facturer. 
Instructions:
1. Open inside wall at proper height for the chimney con-
nector to entry the masonry chimney. 
2. Entry hole to masonry chimney must be lined with an 8
inch (203mm) minimum diameter clay liner, or equiva-
lent, secured with refractory mortar.
3. Construct a 17 inch x 17 inch (432mm x 432mm) outside
dimension frame from 2 x 2 framing lumber to t into wall
opening. Inside opening of frame should be no less than
14 inch x 14 inch (356mm x 356mm). 
4. Attach the wall spacer to the chimney side of the frame.
5. Nail the frame into the wall opening. The spacer should
be on the chimney side.
6. Insert the section of the solid insulated chimney into the
outer wall of the masonry chimney.
7. Tightly secure the length of the solid insulated chimney
with the wall band to the masonry chimney.
8. Insert a section of chimney connector into the chimney.
Make sure it does not protrude past the edge of the clay
chimney liner inside the chimney.
9. Seal the end of the chimney connector to the clay liner
with refractory mortar.
10. Install trim collar around the sold pack chimney section .

Trim Collar
Chimney Section
with 2 inch
(51mm)
Clearance to
Combustibles
Chimney
Connector
Fire Clay Flue
Liner
with Airspace
Masonry
Chimney
Wall Band to
Secure Chimney
Section
Wood Studs Used
for Framing - Spaced
2 inch (51mm)
clearance from
Masonry Chimney
Wall Spacer



Do NOT pack insulation or other combustibles between
spacers.
• ALWAYS maintain specied clearances around vent-
ing and spacers.
• Install spacers as specied.
Failure to keep insulation or other material away from vent pipe
may cause re.
WARNING
1.5”
1.0”
2.0”
2.0”
1.5”
14.0” ID
17.0” OD
ceiling
Minimum18.0”
NFPA 211
13.5” below ceiling to top
of opening
1.0”
8.0”
1.5 2x2 framing stud
2.0 min air clearance
1.0 min air clearance
4.5
or top of opening is a min.of
4.5” below min.clearance
specified by connector mfg.
Center of Hole
Thimble
C
L
C
L
Wall
Include depth
of hearth pad

November 10, 2015 7061-197H 13
Explorer II Medium Wood Stove

This product was designed for and tested on a 6 inch (152mm)
chimney, 14 to 16 feet (420-480cm) high, (includes stove
height) measured from the base of the appliance. The further
your stack height or diameter varies from this conguration,
the greater the likelihood it may affect performance.
Chimney height may need to be increased by 2 - 3% per
each 1000 feet above sea level. It is not recommended to
use offsets or elbows at altitudes above 4000 feet above sea
level or when there are other factors that affect ue draft.

Chimney Connector
Single wall connector or stove pipe.
This must be at least 24 gauge mild steel or 26 gauge blue
steel. The sections must be attached to the appliance and to
each other with the crimped (male) end pointing toward the
stove. All joints, including the connection at the ue collar,
should be secured with 3 sheet metal screws. Make sure
to follow the minimum clearances to combustibles. Where
passage through the wall, or partition of combustible con-
struction is desired in Canada, the installation shall conform
to CAN/CSA-B365.
Factory-built listed chimney connector (vented).
A listed connector (vented) must be used when installing this
unit in a mobile home. The listed connectors must conform
to each other to ensure a proper t and seal.
Flue Gas
Direction
Crimped
End
Toward
Appliance
Secure pipe sections with a
minimum of 3 screws

WARNING

• DO NOT CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION
DUCT OR SYSTEM.
May allow ue gases to enter the house.
Improper installation, adjustment, alteration, service or main-
tenance can cause injury or property damage. Refer to the
owner’s information manual provided with this appliance. For
assistance or additional information consult a qualied installer,
service agency or your dealer.
WARNING
Fire Risk.
Inspection of Chimney:
• Chimney must be in good condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be 6 inch (152mm) UL103 HT.
WARNING
WARNING
ONLY use connector:
• Within the room, between appliance and ceiling or wall.
Connector shall NOT pass through:
• Attic or roof space
• Closet or similar concealed space
• Floor or ceiling
Maintain minimum clearances to combustibles

Follow Chimney Connector Manufacturer’s
Instructions for Proper Installation.
Chimney Flue
Liner
Fireclay
Liner or
Equivalent
Masonry Chimney
Constructed to NFPA 211
Wall Spacer
Wall Band
Trim Collar
Chimney
Connector
1 inch (25mm) Air
Space to Chimney
Section
Min. Clearance
2 inch (51mm)
Min. Chimney Clearance to
Wall Spacer and
Combustibles - 2 inch (51mm)
Chimney Section


(Cont’d)

14 7061-197H November 10, 2015
Explorer II Medium Wood Stove
54-5/8 in.
1388mm
31-7/8 in
810mm
19-1/4 in.
489mm
45-1/2 in.
1156mm
16
(FRONT DOOR OPENING)
35-5/8 in.
minimum
8 in.
35 1/4 in.
minimum
16 in. from glass
Fuel door opening

 
Must extend 2 in.
(51mm) beyond
each side of pipe
(shaded area)
203mm (8 in.)
203mm
(8 in.)
203mm
(8 in.)
457mm (18 in.)
1175mm
(46-1/4 in.)
minimum
1143mm (45 in.)
minimum

FLOOR PROTECTION: Floor protector must be non-combus-
tible material, extending beneath heater and to the front, sides
and rear as indicated. The oor must be non-combustible or
otherwise adequately protected from radiant heat given off by
the unit and from sparks and falling embers. A layer of thin
brick or ceramic tile over a combustible oor is not sufcient.
I t is necessary to install a oor protector (Type I) of a minimum
of 3/8 inch (9.5mm) thick metal clad millboard or equivalent
a minimum of 16 inches (406mm) in front of glass and 8
inches (203mm) to both sides of the fuel loading door. Open
the door and measure 8 inches (203mm) from the side edge
of the opening in the face of the appliance. *
In Canada, similar oor protection must be provided 18 inches
(457mm) in front and 8 inches (203mm) from the sides and
rear of the stove. 
*EXCEPTION: Non-combustible floor protections must
extend beneath the ue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each side. See

WARNING

Hearth pads must be installed exactly as specied.
High temperatures or hot embers may ignite concealed
combustibles.
58-1/4 in.
1480mm
34-3/8 in.
873mm
19-1/4 in.
489mm
48 in.
1219mm
16
(FRONT DOOR OPENING)

USA
CANADA
5 Appliance Set-Up
Corner hearth pad dimensions
with single wall pipe
Corner hearth pad dimensions
with double wall pipe

November 10, 2015 7061-197H 15
Explorer II Medium Wood Stove


A source of air (oxygen) is necessary in order for combus-
tion to take place. Whatever combustion air is consumed
by the re must be replaced. Air is replaced via air leakage
around windows and under doors. In homes that have tightly
sealed doors and windows, an outside air source is needed.
An optional Outside Air Kit is avail able.
Included in OAK-ACC: Termination cap, (2) wire ties, flex
adapter, and fasteners
Items Needed for Installation (not supplied)
• 4 inch ex aluminum pipe, or if using alternate material,
then it shall be made from durable, non-combustible,
heat resistant material up to 350oF. Cut the pipe to the
required length for your installation.
• Phillips head screw driver
• Silicone sealant
• Drills and saws necessary for cutting holes through the
wall or ooring in your home.
1. Remove all materials from packing box.
2. Using a #2 Phillips screw driver attach the ex adapter to
the stove using 4 screws. 
3.Floor & Rear Installation: Cut a 4 inch (102mm) hole in
outside wall or oor to accommodate outside air piping.
Use 4 inch (102mm) aluminum metal ex or rigid piping
to directly connect outside air to appliance intake. Use
the supplied termination cap with a rodent screen. Seal
between the wall (or oor) and the pipe with silicone to
prevent moisture penetration.
WARNING

Do not draw outside combustion air from:
• Wall, oor or ceiling cavity
• Enclosed space such as an attic or garage
• Close proximity to exhaust vents or chimneys
Fumes or odor may result

Outside air inlet must be located to prevent blockage
from:
• Leaves • Snow or ice • Other debris
Block may cause combustion air starvation
Smoke spillage may set off alarms or irritate sensitive individuals.
WARNING

Length of outside air supply duct shall NOT exceed the
length of the vertical height of the exhaust ue.
• Fire will not burn properly
• Smoke spillage occurs when door is opened due to air star-
vation
WARNING


16 7061-197H November 10, 2015
Explorer II Medium Wood Stove

 #2 Phillips head screwdriver
1. Locate bolts supplied with the blower.
2. Align holes in mounting ange of blower with bolt holes in
appliance. Blower should be positioned at bottom of rear
outer skin as shown in 
3. Re-insert and tighten bolts, securing blower onto outer
wall of appliance.
4. Place the bracket containing the snap disc and magnet
under the bottom left rear corner.
See Owner’s Manual for detailed operating instructions
for the blower and snap disc.
Shock Risk.
• Do NOT remove grounding prong from plug.
• Route cord away from appliance.
•
Do NOT route cord under or in front of appliance.
• Plug directly into properly grounded 3 prong receptacle.
CAUTION

MANUAL: Overides the
Snap Disc
AUTO: Fan will turn
ON/OFF Automatically
by the Snap Disc
Controls the Fan Speed

November 10, 2015 7061-197H 17
Explorer II Medium Wood Stove
Convection
chamber top
Flue collar
Flue transition
Upper ue cover



Heat Shield
 #2 & #3 Phillips head screwdriver; 1/2"
wrench
The ue collar is reversible for either a top or rear venting
installation. The appliance is shipped with the ue collar in
the top vent position.
r Rear Vent Installation
and

1. Remove ue collar (#3 Phillips) and convection chamber
top (#2 Phillips).
2. Remove 1 bolt from each side of the ue transition and
retrieve nuts attached to bolts.
3. Turn ue transition to horizontal position. Inspect rope
gasketing to ensure a leak free seal. Re-attach.
4. Remove upper ue cover from convection chamger top.
Rotate 180 degrees and reassebmle. Use paint supplied
to cover unpainted areas.
5. Reattach convection chamber top to ue collar to unit.

Mounting Holes
and Screws

The convection air top assembly can be raised to redirect
air over the top of the appliance by removing 4 screws and
lifting assembly to align with upper mount holes and reas-
semble. 
NOTE: This option is not available for horizontal installs.


18 7061-197H November 10, 2015
Explorer II Medium Wood Stove
CAUTION
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED
Do NOT cut through:
• Floor joist, wall, studs or ceiling trusses.
• Any supporting material that would affect the structural integ-
rity.

NEVER INSTALL IN A SLEEPING ROOM.
Consumes oxygen in the room.
WARNING


1. An outside air inlet must be provided for combustion.
2. Appliance must be secured to the mobile home structure
by bolting the legs to the oor.
3. Appliance must be grounded with #8 solid copper
grounding wire or equivalent and terminated at each end
with N.E.C. approved grounding device.
4. Appliance must be installed with an approved UL103 HT
ventilated chimney connector, UL103 HT chimney, and
terminal cap with spark arrestor. Never use a single wall
connector (stove pipe) in a mobile home installation. Use
only double-wall connector pipe, Dura-Vent DVL, Selkirk
metalbestos DS or Security DL double-wall connector or
any listed double-wall connector pipe.
5. In Canada, this appliance must be connected to a 6 inch
(152mm) factory-built chimney conforming to CAN/ULC-
629M, STANDARD FOR FACTORY BUILT CHIMNEYS.
6. Follow the chimney and chimney connector manufacturer’s
instructions when installing the ue system for use in a
mobile home.
7. Maintain clearance to combustibles.
8. Floor protection requirements must be followed precisely.
9. Use silicone to create an effective vapor barrier at the
location where the chimney or other component penetrates
to the exterior of the structure.
NOTE: Offsets from the vertical, not exceeding 45°, are
allowed per Section 905(a) of the Uniform Mechanical Code
(UMC). Offsets greater than 45° are considered horizontal and
are also allowed, providing the horizontal run does not exceed
75% of the vertical height of the vent. Construction, clearance
and termination must be in compliance with the UMC Table
9C. This installation must also comply with NFPA 211.
NOTE: Top sections of chimney must be removable to allow
maximum clearance of 13.5 feet (411cm) from ground level
for transportation purposes.
10. Burn wood only. Other types of fuels may generate
poisonous gases (e.g., carbon monoxide).
11. If unit burns poorly while an exhaust blower is on in home,
(i.e., range hood), increase combustion air.
12. Installation shall be in accordance with the Manufacturers
Home & Safety Standard (HUD) CFR 3280, Part 24.
Approved for USA Installation only!
6 

November 10, 2015 7061-197H 19
Explorer II Medium Wood Stove
Service Parts Explorer II


R
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. . Provide
model number and serial number when requesting service parts from your dealer or distributor.
Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
Component Pack (Includes Baf e Diverter and Instructions, 2
Leg Leveling Nuts & 2 Bolts, Touch-Up Paint, Owners Manual &
Warranty Card)
Matte Black SRV7061-027
Porcelain Black SRV7061-031
Porcelain Dark Blue SRV7061-032
Porcelain Frost SRV7061-033
Porcelain Mahogany SRV7061-028
Leveling Assembly 7000-000
Paint Touch-Up
Matte Black 812-0910
Porcelain Black 1-00-0022
Porcelain Dark Blue 1-00-0020
Porcelain Frost 1-00-0021
Porcelain Mahogany 855-1450
ACCESSORIES
Blower Assembly BK-ACC
Blower Control Box W/Switch SRV7000-194 
Component Pack 7033-051
Magnet Round SRV7000-140 
Snap Disc Bracket Assembly 7033-036
Snap Disc, # 1, Convection Blower SRV230-0470 
Speed Control Only (Rheostat) 842-0370 
Wire Harness (Blower) 7033-262
Blower, Convection Blower Only 812-4900 
Outside Air Kit, Floor & Rear OAK-ACC
Outside Air Collar Assembly 7033-039
Outside Air Shield 33271 
Firescreen SCR-7061
FASTENERS
Avk Rivnut Repair Kit - 1/4-20 & 3/8-16 Rivnut Tools RIVNUT-REPAIR 
Nut, Ser Flange Small 1/4-20 Pkg of 24 226-0130/24 
Screw, Pan Head Philips 8-32 X 3/8 Pkg of 40 225-0500/40 
Screw, Sheet Metal #8 X 1/2 S-Grip Pkg of 40 12460/40 
Washer, 1/4 Sae Pkg of 24 28758/24 
Service Parts Explorer II


R
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. . Provide
model number and serial number when requesting service parts from your dealer or distributor.
Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
Component Pack (Includes Baf e Diverter and Instructions, 2
Leg Leveling Nuts & 2 Bolts, Touch-Up Paint, Owners Manual &
Warranty Card)
Matte Black SRV7061-027
Porcelain Black SRV7061-031
Porcelain Dark Blue SRV7061-032
Porcelain Frost SRV7061-033
Porcelain Mahogany SRV7061-028
Leveling Assembly 7000-000
Paint Touch-Up
Matte Black 812-0910
Porcelain Black 1-00-0022
Porcelain Dark Blue 1-00-0020
Porcelain Frost 1-00-0021
Porcelain Mahogany 855-1450
ACCESSORIES
Blower Assembly BK-ACC
Blower Control Box W/Switch SRV7000-194 
Component Pack 7033-051
Magnet Round SRV7000-140 
Snap Disc Bracket Assembly 7033-036
Snap Disc, # 1, Convection Blower SRV230-0470 
Speed Control Only (Rheostat) 842-0370 
Wire Harness (Blower) 7033-262
Blower, Convection Blower Only 812-4900 
Outside Air Kit, Floor & Rear OAK-ACC
Outside Air Collar Assembly 7033-039
Outside Air Shield 33271 
Firescreen SCR-7061
FASTENERS
Avk Rivnut Repair Kit - 1/4-20 & 3/8-16 Rivnut Tools RIVNUT-REPAIR 
Nut, Ser Flange Small 1/4-20 Pkg of 24 226-0130/24 
Screw, Pan Head Philips 8-32 X 3/8 Pkg of 40 225-0500/40 
Screw, Sheet Metal #8 X 1/2 S-Grip Pkg of 40 12460/40 
Washer, 1/4 Sae Pkg of 24 28758/24 
7 Accessory List

20 7061-197H November 10, 2015
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
DO NOT DISCARD THIS MANUAL
CAUTION
• Important operating and
maintenance instruc-
tions included.
• Leave this manual with
party responsible for use
and operation.
• Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
DO NOT
DISCARD
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
log onto www.quadrare.com
CONTACT INFORMATION
This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645, 7047962
or other U.S. and foreign patents pending.
We recommend that you record the following pertinent
information for your heating appliance.
Date purchased/installed:
Serial Number: Location on appliance:
Dealership purchased from: Dealer phone:
Notes: