Wildgame t5i20 User manual

Infrared Digital Scouting Camera
User’s Manual Model # t5i20

Includes
Camera Unit 2 - Bungee Cords
User Manual
page 1

RESOLUTION
FLASH
FLASH RANGE
SENSOR
SENSOR RANGE
IMAGE FORMAT
MEMORY
IMAGE RESOLUTION
POWER SUPPLY
BATTERY LIFE
HOUSING
MOUNTING
MAX: 5 MP
18 High Intensity Infrared LED’s
up to 55 feet
Passive Infrared Sensor (PIR) Motion and Heat
up to 60 feet
JPEG - Digital Stills/ AVI-Digital Video
up to 32GB SD Card (not included and required)
Class 4 and above recommended
High (5 MP)
Medium (4 MP)
Low (2MP)
8 AA batteries (not included and required)
Alkaline recommended
Estimated up to 1 year or 30,000 photos
Weather resistant with rubber gaskets
2 Bungee cords - included
page 2
Features

Installing Batteries
1. Open the door at the bottom of the
camera by unlatching the locking
tabs.
2. With the camera facing open, open
the battery compartment cover by
sliding the latch to the left. (Illus-
tration A and B)
page 3
3. With the bottom of the camera to-
wards you, Make sure to insert the
batteries into the camera with the
positive ends towards you where
marked positive and the negative
ends towards you where marked
negative.
Open
Illustration A
Illustration B
NOTE:
Do not mix old and new batteries. Do
not mix alkaline, standard (carbon-
zinc) or rechargable (ni-cad, ni-mh,
etc) batteries.

page 4
4. Close battery compartment cover.
To latch the cover simply pull the
latch slightly to the left as you close
the battery compartment cover.
IMPORTANT:
Make sure the camera is powered off
before removing or installing an SD card.
If you are using an SD card from other
cameras, please make sure to format the
SD card in your computer prior to use in
your camera. New cards are ok to use
straight from the package.
5. Load SD memory card (up to 32GB
not included) into the SD card slot
with the connectors facing down.

page 5
Power On Test Mode
1. To turn the unit ON press and re-
lease the power button.
2. Check the battery level icon
to ensure the batteries just
installed contain the proper
charge level. If so, you are ok to
proceed with camera use.
NOTE: LCD cycle through camera informa-
tion. Time > PIR picture number.
1. LCD Ready Mode: The camera will
automatically enter ready mode if a
button is not pressed for greater than
45 seconds. The status light will illu-
minate during these 45 seconds.
2. PIR LED Status Light: The red PIR
status light will illuminate when a
PIR event is triggered during the
45 seconds the camera is in Ready
Mode. After 45 seconds, all indica-
tor lights will turn off until a button
is pressed.
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m

page 6
Power Save Setting Time
1. After 45 seconds without any buttons
being pushed, the LCD will turn off
and camera enters into Power Save
or Ready Mode.
2.The LCD screen can be awakened by
pressing the Power button briefly.
Note: The LCD will not “wake up”
when camera is writing to memory.
1. To change date and time, start by
pressing and release the center
navigation button to set the hour.
2.Press the left or right navigation
button to go up or down in se-
quence.
3.When the hour is set, repeat
steps 1 and 2 to set the minutes.
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
PM
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m

page 7
Setting Date
1. Press the center navigation but-
ton after setting the minute to
change the Date.
2.Press the up or down navigation
button to go up or down in se-
quence.
3.When the DAY is set, repeat steps
1 and 2 to set the Month and Year.
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
MM
DD
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
MM
DD
Photos
1. Press and release the center navi-
gation button to choose Photos.
The number displayed is the num-
ber of photos on your SD card. This
is not a programmable mode for
the camera.
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m

Image PIR
1. Press the center navigation button
while PIR is selected. The high-
lighted option will be blinking.
2.Press the left or right navigation
button to move to different op-
tions. Press the center navigation
button to save the setting.
1. Press the center navigation button
while Image is selected. The high-
lighted option will be blinking.
2.Press the left or right navigation
button to move to different op-
tions. Press the center naviga-
tion button to save the setting.
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
PIR SENSE:
HI: The PIR detects the smallest movement.
MED: (Default) The PIR detects most com-
mon size movements.
LO: The PIR detects only larger movements.
page 8

Resolution
1. Press the center navigation button
while Resolution is selected. The
highlighted option will be blinking.
2.Press the left or right navigation
button to move to different op-
tions. Press the center navigation
button to save the setting.
RESOLUTION:
HI: Images will be at the highest resolution
but take up the most space.
MED: Images will be at medium resolution
and take up average space.
LO: Images will be at the lowest resolution
and take up the least space.
page 9
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
0432
PM
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
0432
PM
Active
1. Press the center navigation button
while PIR Active is selected. The
highlighted option will be blinking.
2.Press the left or right navigation
button to move to different op-
tions. Press the center naviga-
tion button to save the setting.
PIR ACTIVE:
24 HR: The PIR can be active at all times.
DAY: The PIR can be active in daylight
hours only.
NIGHT: The PIR can be active in nighttime
hours only.
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
PM
Ready
Clock
Date
Photos
Image
PIR
Resolution
Active
Delay
Still Video
Hi Med Lo
Hi Med Lo
24Hr Day Night
15s 30s 1m 2m
PM