Wildgame C8B5 User manual

Invisible Infrared Digital
Cellular Scouting Camera
User’s Manual Model # c8b5

Includes
USB Cable 2 - Bungee Cords User Manual
Flextime Player
Software
Camera Unit Antenna
NOTE: Flextime Player Software is optional. Flextime files can
be played by using most media players
page 1

RESOLUTION
FLASH
FLASH RANGE
SENSOR
SENSOR RANGE
IMAGE FORMAT
MEMORY
USB
IMAGE RESOLUTION
POWER SUPPLY
AUXILIARY POWER
ONBOARD POWER
HOUSING
MOUNTING
CELLULAR TYPE
SIM CARD
MAX: 8 MP
60 High Intensity Invisible IR LED’s
up to 70 feet
Passive Infrared Sensor (PIR) Motion and Heat
up to 60 feet
JPEG - Digital Still / AVI - Digital Video
up to 32GB SD Card (not included and required)
Class 4 and above recommended
5-PIN Mini USB style - included
High (8MP)
Medium (6MP)
Low (4MP)
4 D batteries (not included and required)
Alkaline recommended
External power port
Capacitor to retain Time and Settings
Weather resistant with rubber gaskets
2 Bungee cords - included
2G(GSM) and 3G(WCDMA), CDMA and CDMA2000 not supported
Mini-SIM (2FF) required
Note: Battery life will vary depending on camera settings as well as environ-
mental conditions. Camera settings such as shorter delay periods or even using
Flextime mode are examples of settings that can reduce overall battery life.
Environmental conditions such as extreme cold can also influence battery life.
page 2
Features

Setup
With the camera facing up, open
the battery compartment at the
bottom of the camera by turning
them to the left.
1.
With the bottom of the camera
towards you, load 2 D batteries
with the positive ends towards you
in each chamber.
2.
Close battery compartment cover
by turning them to the right.
3.
Open the door at the bottom of
the camera by unlatching the
locking tabs.
4.
page 3
NOTE:
Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc) or rechargable
(ni-cad, ni-mh, etc.) batteries.
+
+
+
+
--
--

To attach the antenna, place the
bottom of the antenna into the
screw hole at the top of the
camera. Then turn the antenna
clockwise until it is secure. Do
not over tighten.
5. Load SD memory card (up to 32GB
not included) into the SD card slot
with the connectors facing down.
6.
Load Mini-SIM (2FF) card into the
SIM card slot with the connectors
facing down.
7.
IMPORTANT:
Make sure the camera is powered off before
removing or installing an SD card.
If you are using an SD card from other cameras,
please make sure to format the SD card in your
computer prior to use in your camera. New cards are
ok to use straight from the package.
page 4

Power On
1.
Check the battery level icon to
ensure the batteries just installed
contain the proper charge level. If
so, you are ok to proceed with
camera use.
Note: When Powered on or Woken
up, the camera takes 5-10
seconds to check SIM card and/or
Network settings. The buttons
are locked during this period.
2.
To turn the unit ON, press and
release the power button.
page 5
Test Mode
PIR LED Status Light: During the
first 2 minutes of Ready Mode, the
red light will illuminate when a
PIR event is triggered. The red
light will blink for 2-3 seconds
when photo is taken during this
first 2 minutes. After 2 minutes
all indicator lights will turn off
until a button is pressed.
1. LCD Ready Mode: The camera will
automatically enter Ready Mode if
a button is not pressed for greater
than 30 seconds. The status lights
will illuminate for a total of 2
minutes.
2.
UP
OK
L
R
DN
UP
OK
L
R
DN

Power Save Date/Time
1. To change Date & Time, enter
MENU and press the UP,DN,L or R
buttons to navigate to the DATE &
TIME icon and press OK.
2. Press the UP or DN navigation
button to go up or down in
sequence. Press L or R to move to
the next digit.
3. When the Time & Date are set,
press OK to save and press OK
again to go back to the MENU.
page 6
After 30 seconds without any
buttons being pushed, the LCD
will turn off and camera enters
into Power Save or Ready Mode.
1.
The LCD screen can be awakened
by pressing the Power button
briefly.
Note: The LCD will not “wake up” when
camera is writing to memory.
2.
UP
OK
L
R
DN
UP
OK
L
R
DN
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
DATE & TIME
30
UP
OK
L
R
DN
__:__
__/__/__
TIME/DATE
AM
MONTH DAY YEAR
PM
BACK
1
11 01 12
200
UP
OK
L
R
DN
__:__
__/__/__
TIME/DATE
AM
MONTH DAY YEAR
PM
BACK
1
11 01 12
200

page 7
Location
1. To change Location, enter MENU
and press the UP,DN,L or R
buttons to navigate to the LOCA-
TION icon and press OK.
2.Press the UP or DN navigation
button to go up or down in
sequence. Press L or R to move to
the next digit.
3.When the Location is set, press
OK to save and press OK again to
go back to the MENU.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
LOCATION
UP
OK
L
R
DN
BACK
LOCATION
________
AB
UP
OK
L
R
DN
BACK
LOCATION
________
ABCD
Image Type:Still
1. To change Image Type, enter
MENU and press the UP,DN,L or R
buttons to navigate to the Image
Type icon and press OK.
2.
Press the L, R button to select STILL
and press OK. Then select the Resolu-
tion and press OK. Select the
Exposure and press OK. Then select
the aspect and press OK.
3. When the Image Type is set, press
OK to save and press OK again to
go back to the MENU.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+ ™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
IMAGE TYPE
UP
OK
L
R
DN
BACK
STILL VIDEO
HI MED LOW
REGULAR WIDE ANGLE
RESOLUTION
HI MED LOW EXP CONTROL
IMAGE TYPE
Save the location of the area the camera was
installed. This is for your reference and is
optional. If you do not wish to name your
location skip to the next step.
UP
OK
L
R
DN
BACK
STILL VIDEO
HI MED LOW
REGULAR WIDE ANGLE
RESOLUTION
HI MED LOW EXP CONTROL
IMAGE TYPE

Trigger
page 8
TRIGGER:
PIR MODE: Takes a photo or video only when
the PIR sensor is triggered.
FLEXTIME (Time Lapse): Takes time lapse
images at set intervals during the key
movement periods of the day, depending on
your Flextime settings.
BOTH: Both PIR and Flextime are active.
This setting allows you to choose the mode in
which the camera will be capturing images.
1. To change Trigger, enter MENU
and press the UP,DN,L or R
buttons to navigate to the Trigger
icon and press OK.
2.Press the L, R button to select
Trigger Mode. Then select the OK
to save. If PIR is selected press OK
again to go back to the MENU.
Image Type:Video
1. To change Image Type, enter
MENU and press the UP,DN,L or R
buttons to navigate to the Image
Type icon and press OK.
2. Press the L, R button to select
VIDEO and press OK. Then select
the Resolution and press OK. Then
select the length and press OK.
3. When the Image Type is set, press
OK to save and press OK again to
go back to the MENU.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+ ™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
IMAGE TYPE
UP
OK
L
R
DN
BACK
STILL VIDEO
HD REGULAR
15s 30s 1m 2m VIDEO LENGTH
IMAGE TYPE
UP
OK
L
R
DN
BACK
STILL VIDEO
HD REGULAR
15s 30s 1m 2m VIDEO LENGTH
IMAGE TYPE
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
TRIGGER
UP
OK
L
R
DN
BACK
PIR FlexTime BOTH
TRIGGER

PIR ACTIVE:
24 HR: The PIR can be active at all times.
DAY: The PIR can be active in daylight
hours only.
NIGHT: The PIR can be active in
nighttime hours only.
page 9
PIR Sensitivity
1. To change PIR Sensitivity, enter
MENU and press the UP,DN,L or
R buttons to navigate to the PIR
Sensitivity icon and press OK.
2. Press the L, R button to select
the sensitivity and press OK to
save. Then press OK again to go
back to the MENU.
PIR SENSE:
HI: The PIR detects the smallest
movement.
MED: (Default) The PIR detects most
common size movements.
LOW: The PIR detects only larger
movements.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
UP
OK
L
R
DN
BACK
HI MED LOW
PIR SENSITIVITY
Active Time
1. To change the Active Time, enter
MENU and press the UP,DN,L or R
buttons to navigate to the Active
Time icon and press OK.
2. Press the L, R button to select the
active time and press OK to save.
Then press OK again to go back to
the MENU.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
UP
OK
L
R
DN
BACK
24 HR DAY NIGHT
ACTIVE TIME
PIR SENSITIVITY ACTIVE TIME