Wildgame R12i20-7 User manual

Infrared Digital Scouting Camera
User’s Manual Model # R12i20-7

Includes
Adjustable Strap
Flextime Player
Software
Camera Unit
NOTE: Flextime Player Software is optional. Flextime files can
be played by using most media players
page 1
User ManualT-Post Support
T

RESOLUTION
FLASH
FLASH RANGE
SENSOR
SENSOR RANGE
IMAGE FORMAT
MEMORY
IMAGE RESOLUTION
POWER SUPPLY
ONBOARD POWER
HOUSING
MOUNTING
MAX: 12 MP Still
36 High Intensity Infrared LED’s
up to 80 feet
Passive Infrared Sensor (PIR) Motion and Heat
up to 60 feet
JPEG - Digital Stills/ AVI-Digital Video
up to 32GB SD Card (not included and required)
Class 4 and above recommended
High (12 MP)
Medium (8 MP)
Low (5 MP)
8 AA batteries (not included and required)
Alkaline recommended
Built in capacitor to retain Date and Time
Weather resistant with rubber gaskets
Adjustable Strap and custom T-Post mounting
bracket system - included
Note: Battery life will vary depending on camera settings as well as environmental
conditions. Camera settings such as shorter delay periods or even using
Flextime mode are examples of settings that can reduce overall battery life.
Environmental conditions such as extreme cold can also influence battery life.
page 2
Features

Installing Batteries
1. Open the door on the right of
the camera and PULL the tab
towards you. 2. With the camera facing up, open the
compartment door.
page 3
Push the battery latch up to unlock. At the
same time grab the battery compartment out.
BATTERY
UNLOCK

page 4
3. Make sure to insert the AA-cell
batteries based on the direction
labeled on the inside of each com-
partment. Match minus “-” sign
with the marked negative on the
battery and the plus “+” sign with
the marked plus sign on the battery.
4. Load SD memory card (up to 32GB not
included) into the SD CARD slot with the
connectors facing down.
IMPORTANT:
Make sure the camera is powered off before
removing or installing an SD card.
If you are using an SD card from other cam-
eras, please make sure to format the SD card in
your computer prior to use in your camera. New
cards are ok to use straight from the package.
Once the batteries are in the
appropriate spot, return battery
compartment.

page 5
Power On Test Mode
1. To turn the unit ON press and re-
lease the power button.
2. Check the battery level icon
to ensure the batteries just
installed contain the proper
charge level. If so, you are ok to
proceed with camera use.
NOTE: LCD cycle through camera in-
formation. Time > PIR picture number
> Flextime number > Remaining pic-
tures > Temperature
1. LCD Ready Mode: The camera will
automatically enter Ready Mode if a
button is not pressed for greater than
30 seconds. The status lights will il-
luminate for a total of 2 minutes.
2. PIR LED Status Light: During the
first 2 minutes of Ready Mode, the
red light will illuminate when a PIR
event is triggered. The red light will
blink for 2-3 seconds when photo
is taken during this first 2 min-
utes. After 2 minutes all indicator
lights will turn off until a button is
pressed.
RESET
POWER
OK

page 6
Power Save Setting Time
1. After 30 seconds without any buttons
being pushed, the LCD will turn off
and camera enters into Power Save
or Ready Mode.
2.The LCD screen can be awakened by
pressing the Power button briefly.
Note: The LCD will not “wake up”
when camera is writing to memory.
1. To change date and time, start by
pressing and release the OK but-
ton to set the hour.
2.Press the up or down navigation
button to go up or down in se-
quence.
3.When the hour is set, repeat
steps 1 and 2 to set the minutes.
RESET
POWER
OK
RESET
POWER
OK
RESET
POWER
OK

page 7
Setting Date Location
1. Press the OK button after setting
the minute to change the Day.
2.Press the up or down navigation
button to go up or down in se-
quence.
3.When the DAY is set, repeat steps
1 and 2 to set the Month and Year.
1. Press the OK button while LOCA-
TION is selected. The first charac-
ter will be blinking.
2.Press the UP or DOWN naviga-
tion button to go up or down in
sequence. Press the OK button or
the Left and Right navigation but-
ton when the character shown is
what you want and move to the
next character.
3.Repeat steps 1 and 2 to set the rest
of the characters. Press the right
navigation button to skip spaces
and save the location name.
Save the location of the area the camera was
installed. This is for your reference and is op-
tional. If you do not wish to name your location
skip to the next step.
RESET
POWER
OK
RESET
POWER
OK
RESET
POWER
OK
RESET
POWER
OK

page 8
Location Trigger Flextime
1. Press the OK button while Trigger
is selected. The highlighted option
will be blinking.
2.Press the left or right naviga-
tion button to move to different
options. Press the OK button to
save the setting.
TRIGGER:
PIR MODE: Takes a photo only when the PIR
sensor is triggered.
FLEXTIME(Time Lapse): Takes time lapse images
at set intervals during the key movement pe-
riods of the day, depending on your Flextime
settings.
BOTH: Both PIR and Flextime are active.
This setting allows you to choose the mode in
which the camera will be capturing images. 1. Press the OK button while Flex-
time is selected. The highlighted
option will be blinking.
2.Press the left or right naviga-
tion button to move to different
options. Press the OK button to
save the setting.
The Interval setting is set by the Delay Set-
ting on the camera with a 1 minute minimum
Flextime delay. See chart on the next page for
Flextime options.
NOTE: Camera needs at least 48 hours in the
field to acclimate to the environment for Flex-
time to function properly.
Reminder: Only use “Flextime” and “Both”
modes if you are wanting to use time lapse
technology. These modes can reduce battery
life versus the standard “PIR” mode.
RESET
POWER
OK
RESET
POWER
OK
RESET
POWER
OK
RESET
POWER
OK

Flextime period:
1. 15 min before Sunrise
to 1 hour after Sunrise.
2. 1 hour before Sunset to
15 min after Sunset
Flextime period:
1. 15 min before Sunrise
to 1 hour after Sunrise.
2. 1 hour before Sunset to
15 min after Sunset
Flextime period:
1. 15 min before Sunrise
to 15 min after Sunset
P1
P2
FLEXTIME selected
INTERVAL
Camera is inactive before and after Flextime periods.
INACTIVE
15 MINUTES
BEFORE
SUNRISE FLEX
TIME
1 HOUR
AFTER
SUNRISE
INACTIVE
1 HOUR
BEFORE
SUNSET
FLEX
TIME
15 MINUTES
AFTER
SUNSET
INACTIVE
Flextime is active twice a day.
Camera is in PIR mode before and after Flextime periods. Flextime is active twice a day.
PIR
15 MINUTES
BEFORE
SUNRISE FLEX
TIME
1 HOUR
AFTER
SUNRISE
PIR 1 HOUR
BEFORE
SUNSET
FLEX
TIME
15 MINUTES
AFTER
SUNSET
PIR
PIR
15 MINUTES
BEFORE
SUNRISE
FLEXTIME
15 MINUTES
AFTER
SUNSET
PIR
Camera is in PIR mode before and after Flextime periods. Flextime is active during daytime.
Flextime + PIR period:
1. 15 min before Sunrise
to 1 hour after Sunrise.
2. 1 hour before Sunset to
15 min after Sunset
Flextime + PIR period:
1. 15 min before Sunrise
to 1 hour after Sunrise.
2. 1 hour before Sunset to
15 min after Sunset
Flextime + PIR period:
1. 15 min before Sunrise
to 15 min after Sunset
P1
P2
BOTH selected
INTERVAL
Camera is inactive before and after Flextime + PIR periods.
INACTIVE
15 MINUTES
BEFORE
SUNRISE FLEX
TIME
1 HOUR
AFTER
SUNRISE
INACTIVE
1 HOUR
BEFORE
SUNSET
FLEX
TIME
15 MINUTES
AFTER
SUNSET
INACTIVE
Flextime + PIR is active twice a day.
Camera is in PIR mode before and after Flextime + PIR periods. Flextime + PIR is active twice a day.
PIR
15 MINUTES
BEFORE
SUNRISE FLEX
TIME
1 HOUR
AFTER
SUNRISE
PIR 1 HOUR
BEFORE
SUNSET
FLEX
TIME
15 MINUTES
AFTER
SUNSET
PIR
PIR
15 MINUTES
BEFORE
SUNRISE
FLEXTIME & PIR
15 MINUTES
AFTER
SUNSET
PIR
Camera is in PIR mode before and after Flextime + PIR periods. Flextime + PIR is active during daytime.
PIR PIR
PIR PIR
page 9