Wiley x WX VAPOR User manual

ERX-ICVPR (3)
MAINTENANCE: Wiley X lenses are specially coated to offer superior abrasion
resistance. Please follow below instructions to prolong the life of your lenses
and keep them performing at their best:
WARNING: Wiley X brand eyewear is tested tough. However, impact resistant
eyewear is not unbreakable and does not provide unlimited eye protection under all
circumstances and conditions. Misused, abused, scratched and/or damaged
eyewear can reduce impact protection (and void your limited warranty). Dirty
and/or wet eyewear can impair vision and reduce safety (resulting in personal injury
and/or property damage). Keep your Wiley X eyewear clean with water only. Do not
use solvents or abrasives as it could scratch or damage the product reducing its
effectiveness. Store your Wiley X eyewear in the protective case provided to
prolong the life of the lenses. Most of all, take all appropriate precautions when
wearing your Wiley X eyewear during hazardous and/or dangerous activities and
conditions. Wiley X, Inc. is not responsible for personal injury, property damage or
losses incurred while using Wiley X brand products.
LENS REMOVAL - STEP 2
Detach the outer lens hooks from the frame.
5)
LENS REMOVAL
- STEP 1
A
A
The nose piece
and primary lens
are interlocking.
1)
To detach pull a leg
of the nose piece.
Once the leg is
disengaged the
nose piece will
simply rotate out.
2)
NOSE PIECE REMOVAL*
*Should you require corrective lenses, remove the Rx insert
prior to removing the nosepiece. See Rx insert instruction.
Work the leash cord sleeves over the temple tip until secure.
OPTIONAL LEASH CORD
Clean lenses with water only.
Do not use solvents or special cleaners.
Use micro-fiber cleaning cloth provided to gently wipe clean.
Never use paper products to clean and avoid wiping lens surface when dry
and/or dirty as this may potentially scratch the lens.
Remove nose piece (see nose piece removal).
With one hand firmly grasp the frame directly above
the nose piece. Do not pull from the edges (Ref A).
With the opposite hand grasp the lens.
Firmly pull on the lens to detach the lens from the center of the frame.
Note: Pulling lenses from the corners of the frames (See “A”) may damage
the frame or the lenses.
2)
1)
3)
4)
WX VAPOR
INSTRUCTIONS
COPYRIGHT © 2017 WILEY X, INC. ALL RIGHTS RESERVED.
WILEY X, WX, BLACK OPS, logos, tag lines and product names are trademarks or registered trademarks (marcas
registradas) of Wiley X, Inc. in the U.S. and other countries. Logos © 2007-2017 Wiley X, Inc. All rights reserved.
7800 PATTERSON PASS ROAD, LIVERMORE CA 94550 USA
SØNDERGADE 8-10 7570 VEMB DENMARK
WX EMEA LLC: [phone] WILEYX.EU
WILEY X INC: 1.800.776.7842 925.243.9810 WILEYX.COM

NOSE PIECE INSTALLATION - STEP 1
Align grooves of nose piece into the lens.
1)
NOSE PIECE INSTALLATION - STEP 2
Position hand as pictured and squeeze together until
the nose piece completely seats into the lens.
2)
LENS INSTALLATION - STEP 1
Attach outer corners of lens into frame.
1)
LENS INSTALLATION - STEP 2
Align center lens slot into center catch of the frame.
2)
Squeeze the lens and frame together.
3)
*Should you require corrective lenses, remove the Rx insert
prior to removing the nosepiece. See Rx insert instruction.
INSTALLING THE CORRECTIVE
LENS INSERT
Remove the nose
piece from the
lens as directed
in “nose piece
removal.”
1)
Fully insert the
post at the top
of the nosepiece
into the slot of
the rx insert.
2)
Install the nose
piece into the lens.
3)
RX INSERT INSTRUCTION
Place hands as pictured.
1)
Gently push up with thumbs until Rx insert
disengages from post.
2)
REMOVING THE CORRECTIVE LENS INSERT