Williams-Sonoma COLONIAL CANOPY BED QUEEN & KING User manual

Date: 19-November-15
Rev:
COLONIAL CANOPY BED QUEEN & KING
Page
1
of
4

Date: 19-November-15
Rev:
Important Safety Instructions:
•Please read all instructions carefully before assembling.
•For your safety, assembly by two or more adults is strongly recommended.
•Keep instructions for future use.
•Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Part Included Box.1:
•Headboard
(1) Headboard Panel (A)
(1) Bottom Rail (B)
•Footboard
(1) Footboard Panel (C)
To Assemble Bed:
1. Insert threaded rods (M) into the inserts in headboard posts (D) and footboard posts (E) as shown fig 1 in
illustration step 1.
2. Attach the headboard panel (A) and bottom rail (B) by inserting threaded rod (M) on the posts into the holes on the
headboard panel (A) and bottom rail (B) as shown fig 2. (Note: Hardware connections are on the back side of
headboard panel)
3. Place curved washers (N), flat washers (Q), spring washers (P) and nuts (O) onto the threaded rod (M) attached on
the posts (D). Tighten with wrench (V) as shown in illustration step 3.
4. Attach the footboard panel (C) by inserting threaded rods (M) attached on the footboard posts (E). Repeat step 3.
(Note: Hardware connections are on the back side of footboard panel)
D & E
A
B
E C
Parts Included Box.2:
•(2) Headboard Post (D)
•(2) Footboard Post (E)
•(2) Side Rails (F
)
•(2) Roll Slats (G)
•(1) Center rail (H)
•(3) Long Leg Supports (I)
•(3) Short Leg Supports (J)
•(2) Short Canopy Rail (K)
•(2) Long Canopy Rail (L)
•Hardware packet containing the
following
Fig.1
Fig.2
Fig.3
Step 1. Insert threaded rod
Step 3. Attach h
ardware
Page
2
of
4

Date: 19-November-15
Rev:
5. Determine the desired height of the side rail lips. The lips have been pre-attached to the lower position (boxspring
level) on each side rail. Lips may be adjusted to the higher position (platform level – makes boxspring optional) by
removing the Allen bolts ¼” x 1 ½” with the enclosed Allen key (U) and re-attaching lips to the higher set of
pre-drilled holes. Re-tighten bolts with Allen key (U). Caution: The lips on both side rails and the center rail (Step 8)
must all be affixed at the same height.
SIDERAIL LIP
Boxspring level Platform level
6. Insert threaded rods (M) into the inserts in posts of the headboard as shown fig 5 in illustration step 6. Repeat
insert threaded rod (M) to the footboard posts.
7. Attach side rails (F) to headboard and footboard by pushing side rails (F) into position so that threaded rods extend
into side rails as shown in fig 6. Place curved washers (N), flat washers (Q), spring washers (P) and nuts (O) onto
the threaded rods (M) attached on the posts of the headboard and footboard. Tighten with wrench (V) as shown in
illustration step 7.
Step 5. Determine side rail lip height.
Fig.4
Step 7. Attach side rail to HB & FB
Step 6. In
sert threaded rod
Fig.5 Fig.6
Page
3
of
4

Date: 19-November-15
Rev:
8. Determine the correct center rail height by reviewing the selected side rail heights. (Step 5) For lower position
(boxspring level) attach the (3) shorter support legs to the center rail. Insert the Allen bolts (S) through the
pre-drilled holes on the top side of center rail and into the shorter legs. Tighten with Allen key (U). For higher
position (platform level) attach the (3) longer legs. The unused set of legs can be attached to the bottom side of
the center rail for storage. Align them horizontally and attach with the single ¼” x 115 Allen bolt. (R).
9. Attach the mid beam (H) to the headboard and footboard by sliding it onto the bed fitting as shown.
10. Lay slat rolls (G) in place over center rail and side rail lips. Attach by inserting the Phillips screws (W) through
pre-drilled holes and tightening with a screwdriver (not included).
11. Attach the canopy rail by aligning the notches in the canopy rail as shown below with the notches at the top of the
posts. Insert Allen Bolts (T) and tighten with enclosed Allen Key (U) as shown.
12. Tighten all connections.
Care Instructions:
•Dust often using a clean, soft, dry and lint-free cloth.
•Blot spills immediately and wipe with a clean, damp, cloth.
•We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
Step 8.Detemine center rails height
Step 9.Attach center rails to HB & FB
Adjust leveler if needed
Step 10.Install slat rolls
Step11.Install canopy rail to posts
Fig.7
Fig.8
Page
4
of
4
T
hank you for your purcha e
tore | catalog