Williams-Sonoma MORGAN RECT 80 DINING TABLE User manual


Date:02‐Apr‐15www.williams‐sonoma.comPage1of6
Rev: 





MORGAN RECT 80” DINING TABLE










Date:02‐Apr‐15www.williams‐sonoma.comPage2of6
Rev: 
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
Parts Included:
(A)
(B)
(C)
(D)
Top
Extension Leaf
Leg
Stretcher
1x
2x
2x
1x
Hardware Included:
(E) Flat Washer
(F) Spring washer
(G) Allen Bolt
M8
(H) Fitting

(I) Allen key
11x 11x 11x 4x 1x
A
B
C
D
B
C


Date:02‐Apr‐15www.williams‐sonoma.comPage3of6
Rev: 
(J) Thumb screw with
washer
4x

Assembly Instruction Steps:
1. Attached the stretcher (D) to leg (C) by inserting the exposed dowel on the stretcher into pre-drilled holes on the
leg.
2. Secure by fitting (H) flat washer (E), spring washer (F) and Allen bolt (G) using Allen key (I).

3. Attach the remaining leg (C) onto the stretcher (D) by aligning the pre-drilled holes on the leg with exposed
wood dowels on the stretcher.
4. Secure the leg by fitting (H) flat washer (E), spring washer (F) and Allen bolt (G) using Allen key (I) as shown
below.
2x H
E
F
G
I
D
C


Date:02‐Apr‐15www.williams‐sonoma.comPage4of6
Rev: 
5. Slowly place the top (A) on the assembled legs & stretcher (C&D) by aligning the pre-drilled holes on the
bottom side of top with exposed wood dowel on top of legs.
6. Secure the top (A) by flat washer (E), spring washer (F) andAllen bolt (G) usingAllen key (I) as shown.

7. Unlock and pull the table top end rails to open.
8. Lay the extension leaves (B) onto the top.
9. Align the pre-drilled holes on one side of the extension leaf (B) with the exposed metal pins on the top (A).
7x
2x
C
A
H
E
F
G
I
I
E
F
G


Date:02‐Apr‐15www.williams‐sonoma.comPage5of6
Rev: 

10. Push the two end rails in to close the top
11. Secure the runners with 4 thumb screws with washer (J) by turning counter clockwise from the underside of the
table top, as seen in the illustration below.
Note: Thumb Screws will need to go through the runner and insert into the nut which is pre-assembled on the
underside of top.



Adjusting the levelers:
Due to an uneven floor, the furniture may not sit level due causing it to wobble. If the furniture wobbles, determine
D
D
J


Date:02‐Apr‐15www.williams‐sonoma.comPage6of6
Rev: 
which corner does not touch the ground correctly. With two people follow these steps:
1) Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
2) Turn the levelers until adequate contact will be made with the floor. Gently set down the piece and check
stability.
3) Repeat steps until furniture sits firmly on the ground.
12. Assembly is complete.
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
For glass tops and shelves, glass cleaner may be used, but avoid spraying it onto the metal or ceramic
frame.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thankyouforyourpurchase
Stores | catalog