Willis & Gambier Camille 3388N User manual

Thank you from
Willis & Gambier
For a chance to win a Love 2 Shop voucher simply posta picture of your new product on
your preferred social channels tagging Willis & Gambier using the hashtag #ShareYourStyle
and #WillisGambier . One winner will be selected at random each month.
To view our full terms and conditions pleasevisit www.willisgambier.co.uk
Are you happy with your purchase?
Yes: That’s great, we would love to hear more from you. Please leave us a review on
our social media channels.Your feedback will be greatly appreciated.
No: If for any reason there is something missing, indifferent or incorrect with your
order, please contact the retailer you purchased the item from.We will work
with the retailer to resolve your issue as quickly as possible.

Please check the pack contents before attempting to assemble this product. A full checklist of components is given
in this leaflet. If any components are missing, please contact the retailer from whom you bought this product.
The fittings pack contains which should be
Read this leaflet in full before commencing assembly.
You will require a crosshead screwdriver and an open ended spanner to assemble this product.
SMALL ITEMS KEPT AWAY FROM YOUNG CHILDREN.
This product is , it should be assembled as near as possible to the point of use.
to avoid personal injury and (or) damage to the product.
This product takes approximately to assemble with
HEAVY TAKE CARE WHEN
LIFTING
60 MINUTES 2 PEOPLE.
Step By Step Assembly Instructions
1.
2.
3.
4.
5.
6.
PRE-ASSEMBLY PREPARATION
Page 1
135cm Low End Bedstead (Product Code CA/3388N)
150cm Low End Bedstead (Product Code CA/3389N)
180cm Low End Bedstead (Product Code CA/3390N)
Camille Bedroom Collection
135cm High End Bedstead (Product Code CA/3391N)
150cm High End Bedstead (Product Code CA/3392N)
180cm High End Bedstead (Product Code CA/3393N)
IMPORTANT NOTE.
If you have the low end version of this
bedstead the assembly procedure is
identical.
Lifestyle furniture collections

4
o
A
C
C
D
B
E
Panel and Fittings Identification
1 set
2 set
Nut & Washer
45mm Bolt & Washer
P
1
Centre Rail Support Leg
+
NWood Dowel
Open Ended Spanner
O
+
20mm CSK Screw

4
Page 3
A
B
C
C
88
Fittings
‘Insert the four wooden dowels (N) into the headboard and footboard. This will
assist in the alignment of the siderail.Screw the eight threads (F) into the
headboard and footboard and tighten by hand.
N X N
IMPORTANT NOTE.
Ensure that when the side rails are in position
the holes on the slat support rail are facing
upwards.

Page 4
C
C
Step - Locate the side rails onto the threads protruding from the footboard. Locate the washer &
nut onto the threads and secure by hand at first. Tighten using the open ended spanner
(Provided).
3
B
Fittings
G x 4 Spanner, H
G
Attach the brackets (M) to the headboard and footboard using the screws (I) inserted
Step -
into the pre-drilled pilot holes. Tighten using a crosshead screwdriver.
4
I x 12
M x 2
Fittings
M
I

L
E
o
Page 5
Please note.
The holes in the slat support rail
should be facing upwards.
D
the nuts(K) and bolts(J). Tighten using the open ended spanner(H)
- Locate the centre rail(D) into the headboard and footboard brackets,and secure using
secure using the bolt and washer(P).
- First attach the centre rail support leg(O) into the underneath of the centre rail(D), and
Step 5
K x 2
P x 1
Fittings
J x 2
D
K
J
P
Step - Push fit two plastic caps onto either end of the slat. Push fit the slat into the pre-drilled pilot
holes. Please note that it may require a light tap with a soft hammer to secure the plastic
end caps into the holes. Repeat this step with the other 3 slats.
The assembly is now complete.
1/ 33
6
Fittings
L x 64
135cm bedstead
150/180cm bedstead L x 68