1
General
information
About this document
The language of the original operating
instructions is English. All other languages of
these
instructions
are translations of
th
e
original operating
in
st
r
u
ct
i
ons
.
These installation and operating inst
ruct
ions
are an integral part of the product. They
must
be kept readily available at the place where
the product is installed.
Strict
adherence
to
these instructions is a precondition for
the
proper use and correct operation of
th
e
produc
t.
These installation and operating inst
ruct
ions
correspond to the
relevant
version of
th
e
product and the underlying safety
stan
dards
valid
at the time of going to
prin
t.
Supplied pump will operate trouble free and
satisfactorily on the condition that, it is
installed with due care and maintained
properly.
For hassle free operating life, it is
recommended that the pump should operate
under specified “Operating conditions”. Pump
operating conditions are mentioned on the
“Nameplate”affixed to the pump.
If operating parameters deviate from the
specified parameters as on the “Nameplate”,
please contact manufacturer.”
2 Safety
These operating instructions contain basic
information which must be adhered to during
installa
t
i
on and operation. For this reason,
these operating instructions must, without
fail, be read by the service
t
e
ch
nic
i
an and
the
responsible operator before
i
n
s
t
a
ll
ation and
commissioning. The machine operator list
must be filled out completely. By signing this
list,
all
persons working on or
with
the product
confirms
that
they have received, read and
understood
this operating & maintenance
manual.
It is not only the g
e
n
e
r
a
l
safety
i
n
s
t
r
u
ct
i
on
s
listed under the main point "safety"
that
must
be
adhered
to but also the
spe
c
i
a
l
safety
instructions
with danger symbols included under
the
following
main points.
2.1 Designation of information in
the
operating instructi
o
ns
Symbols:
General
danger symbol
Danger
due to electrical voltage
NOTE:
...
Signal words:
DA
NG
ER
!
Acutely dangerous situation
Non-observance results in death or the most serious of
injuries.
WARNING!
The user can suffer (serious) injuries.
“Warning”
implies that (serious) injury to
p
e
r
s
ons
is
p
r
oba
ble if
this information is disregarded.
CAUT
IO
N!
There is a risk of damaging the pump/installation.
“Caution” implies that damage to the pro- duct is
likely if the
information
is disregarded.
Useful information on using the product. It also draws
attention
to possible problem
s
.
2.2 NOTE:
Personnel qualifications
The installation prsonne
l
must have the approp
r
i
at
e
qu
alifica
t
i
on for this work.
2.3 Danger in event of non-observance of the safety
instructions
Non-observance of the safety
i
n
structi
ons can result
in risk of injury to persons and damage to
product/installation. Non-observance of the safety
instructions
can result in the loss of any claims
to
damages.
I
n
det
a
i
l
,
non-observance
can, for example, result in
the following risks:
Failure of important product/installation function
s
Failure of required maintenance and repair
procedures
Danger to persons from electrical, mechanical and
bac
t
eriologica
l
influences
Property damage
2.4 Safety consciousness on the job
The safety instructions included in
these
i
n
s
t
all
ation
and operating instructions,
the
existing
nat
i
onal
regulations for
accident
pr
e
v
ent
i
on together with any
internal working, operating and safety regulations of
the operator are to be complied with
.
2.5 Safety instructions for the
ope
r
ator
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision o
r
instruction concerning use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure
that
they do not play with the
appliance.
If hot or cold components on the
product/the
unit
lead to hazards, local measures must be taken to
guard them against
touc
hing.
Guards pro
t
e
c
t
i
ng
against
touching moving
components (such as the coupling) must
not
be
removed
w
h
ils
t
the product is in oper
at
i
on
.
L
eakages
(e.g. from the shaft seals) of hazardous
fluids (which are explosive, toxic or hot) must be led
away so that no danger to persons or to the
environment arises. National statutory provisions
are to be complied with.Highly f
l
ammable materials
are always to be kept at a safe distance from the
product.
