WilTec 60143–60146 User manual

Operation Manual
US Mailbox
60143–60146, 60337–60340, 60341–60344
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

© by WilTec Wildanger Technik GmbH Item 60143–60146, 60337–60340, 60341–60344 Page 2
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: [e-mail]
Tel:[phone]
Fax: [phone]
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [email protected]o
Tel:[phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 60143–60146, 60337–60340, 60341–60344 Page 3
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
Intended use
Designed as a mailbox for everyday use, being suitable for outdoor use
Parts list
№
Name
Qty.
№
Name
Qty.
A
Top lock
1
E
New mail flag
1
B1
Rust-resistant screws (short)
5
F
Flag holder
1
B2
Rust-resistant screws (long)
1
G
Letterbox/mailbox
1
C
Rust-resistant screw nuts
6
H
Washer
2
D
Bottom lock
1
I
Assembly instruction
1
Safety precautions
•When assembling, please be careful to ensure that the hinges do not pinch your skin.
•When mounting the article, please ensure that it is attached securely, and take into account the
risk of accidents when selecting a location.
Care and storage
•Clean with water only, never with abrasive products!
•Then wipe dry with a clean cloth.
•Hint! Grease the door hinges once a year.

© by WilTec Wildanger Technik GmbH Item 60143–60146, 60337–60340, 60341–60344 Page 4
http://www.WilTec.de
http://www.aoyue.eu 06 2021-1
http://www.teichtip.de
Assembly
1. Place the top lock (A) over the mailbox (G) so that the holes match the appropriate drilling holes.
2. Screw two screws (B1) into the drilled holes.
3. Secure the screws from the inside with two nuts (C).
4. Place the bottom lock (D) so that the holes match the appropriate drilling holes.
5. Screw two screws (B1) into the bored holes.
6. Secure the screws from the inside with two nuts (C).
Attaching the flag
1. Place one washer (H) on the front and one on the rear of the flag (E).
2. Put the flag (E) in the appropriate drilling holes.
3. Screw the long screw (B2) into the top hole and the short screw (B1) into the bottom hole.
4. Secure the screws from the inside with two hexagon nuts (C).
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.