WilTec 61935 User manual
Operation Manual
Table Saw
61935, 61936
!!"#$"
%!!"#$
"
"""
&'
(
'
'))))
'
')))
*'
!!"#$
+,-.
/..01%
#
"2*"'
!!"#$
+,.3
/..01%
#
"
%'(
'401.056///1.5
78'401.056///1.-/
8
8
!!"#$
+,.3
/..01%
%'[email protected]
'401.056///1.5
78'401.056///1.-/
9!!"#$ :-16/:-16: ;.
'))!
')) 5..5.--
'))
Introduction
"< To ini ize the risk of injury we urge that our cli-
ents take so e basic safety precautions when using this device. Please read the operation in-
structions carefully and ake sure you have understood its content.
+
**
=
>
Intended use
<
Work pieces with a round or irregular cross-section (e.+g. firewood) ust not be sawn,
as they cannot be held securely during sawing.
Operator require ents
<
<
Qualification: <
Mini u age:-3
8
"
Training:<
>
9!!"#$ :-16/:-16: ;6
'))!
')) 5..5.--
'))
Technical data
Intake voltage?@A .65
Frequency?$>A /5
No inal power consu ption?!A 355
Idle speed?A .1/5
Saw blade dia eter × drill hole dia eter?A .55B-:
Riving knife size?A ..
Max. cutting depth?A 90° 0/
45° .C
Weight?"A 11
Sound pressure level LpA?=? AA?-A 1C
Sound power level LWA?=? AA?-A --5(Wear hearing protection!)
Value of vibration e ission ah?)DA?.A E./
Protection class
?-AF%G:-5.1+H6=? A
?.AF%G:-5.1
Warning:
7
""
%
""
Residual risks
Risk of injury! G
>I
"J
J
9!!"#$ :-16/:-16: ;0
'))!
')) 5..5.--
'))
E ergency behaviour
"J<
;J
"G-6-:0
" "
!<'
◦(WHERE?),
◦(WHAT?),
◦J(HOW MANY?),
◦GJ(HOW?).
General safety instructions
Caution:
Read all safety instructions and operating instructions.7
")J
Keep all safety instructions and instructions for the future.KL
?A
?A
Workplace safety
Keep your work area clean and well lit. "
Do not work with the power tool in a potentially explosive environ ent containing fla -
able liquids, gases or dusts. ;"
Keep children and other persons away while using the electric tool.
Electric safety
The connector plug of the power tool ust fit into the socket.
"""
Avoid physical contact with earthed surfaces such as pipes, heaters, stoves and refri-
gerators.""
Keep power tools away fro rain and oisture. ;
""
Do not isuse the cable to carry, hang, or disconnect the power tool. Keep the cable
away fro heat, oil, sharp edges, or oving parts.
""
When working with an outdoor power tool, use only extension cables that are suitable
for outdoor use.8"
"8
If operation of a power tool in a hu id environ ent is unavoidable, use a residual cur-
rent circuit breaker.""
"
Personal safety
Be attentive and always pay attention to what you are doing and go to work with a
power tool with co on sense.
9!!"#$ :-16/:-16: ;/
'))!
')) 5..5.--
'))
J
Wear personal protective equip ent and safety glasses at all ti es. !
<"
"J
Avoid unintentional co issioning.F"
")
Re ove adjust ent tools or wrenches before turning on the power tool.
J
Avoid abnor al posture. Make sure that you stand securely and keep your balance at
all ti es.8
Wear suitable clothing. J+
MJ
If dust extraction and collection devices can be installed, ake sure that they are con-
nected and used correctly. 8>
Safe use and handling of the power tool
Do not overload the device. Use the appropriate power tool for your work. !
"
Do not use any power tool with a defective switch.
Unplug and/or re ove the battery before aking any adjust ents, changing any ac-
cessories, or putting the unit away.
Keep unused power tools out of the reach of children. Do not allow anyone to use the
unit who is not fa iliar with it or has not read these instructions. ;
8
Carefully aintain power tools. Check that oving parts function correctly and do not
ja , that parts are broken or da aged in such a way that the function of the power tool
is i paired. Da aged parts ust be repaired before using the unit again. F
Keep cutting tools sharp and clean. N
J
Use power tools, accessories, insert tools, etc. according to the instructions. Take into
account the working conditions and the activity to be perfor ed.
Service
Have your power tool repaired only by qualified personnel and only with original spare parts.
Alternatively, contact the anufacturer or an authorized service partner.
Safety instructions concerning the circular table saw
Operation is only per itted with a residual current circuit breaker (RCD, ax. residual current
30+ A).
!G8
!
"
8"
="8
$
9!!"#$ :-16/:-16: ;:
'))!
')) 5..5.--
'))
G%@%
7"<
7
N"
7I
&""""JM
;
!
"
"""
&
%G30C-
&
8
"
>?A
J
Maintenance
The plug ust ALWAYS be disconnected fro the socket
before carrying out any work on the device!
<
8O
*
*
J
"
J)8
9!!"#$ :-16/:-16: ;C
'))!
')) 5..5.--
'))
Inspection after receipt
;"
>
Scope of delivery
9!!"#$ :-16/:-16: ;3
'))!
')) 5..5.--
'))
Disposal regulations
% ?!%%%.5-.)-1)%A
<
! !%%%
<
!"#$ # %
!%%%%0/.36C50
? %
%
A
"
<
=
%
F
'
!!"#$
+,-.).3
/..01%
'
8
<!!"#$
9!!"#$ :-16/:-16: ;-C
'))!
')) 5..5.--
'))
Other manuals for 61935
1
This manual suits for next models
1
Other WilTec Saw manuals
WilTec
WilTec 61917 User manual
WilTec
WilTec 51331 User manual
WilTec
WilTec 61950 User manual
WilTec
WilTec 61917 User manual
WilTec
WilTec 51331 User manual
WilTec
WilTec 61076 User manual
WilTec
WilTec 62554 User manual
WilTec
WilTec 62850 User manual
WilTec
WilTec 61935 User manual
WilTec
WilTec 61950 User manual
